892395f
M95020-DRDW3TP
The maker sells this part only as M95020-DRDW3TP/K (ST ordering information scheme: "T = Tape and reel packing", "/K = Manufacturing technology code"; the bare code lacks the process letter (Table 18, p.39)). The DigiKey and Mouser numbers on this page are for M95020-DRDW3TP/K.
STMicroelectronics · EEPROM · TSSOP-8
M95020-DRDW3TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ~{S} | input | Chip Select: driving it low selects the device and starts communication, driving it high deselects the device and puts Q in high impedance; it should follow VCC at power-up, for example through a pull-up resistor. |
| 2 | Q | tri_state | Serial Data output: shifts data out on the falling edge of Serial Clock (C), MSB first, during a Read, and is high impedance in all other cases. |
| 3 | ~{W} | input | Write Protect (active low): write-protects the Status Register, and a low level stops the WRSR and WRITE instructions from being executed. |
| 4 | VSS | power_in | Ground: the reference for all signals, including the VCC supply voltage. |
| 5 | D | input | Serial Data input: receives instructions, addresses and data to be written, latched on the rising edge of Serial Clock (C), MSB first. |
| 6 | C | input | Serial Clock: synchronizes the serial interface, with data on D latched on the rising edge and data on Q changing after the falling edge. |
| 7 | ~{HOLD} | input | Hold (active low): pauses serial communication without deselecting the device; Q is high impedance and D and C are Don't Care during Hold, and the device must be selected (S low) to start it. |
| 8 | VCC | power_in | Supply voltage: 2.5 V to 5.5 V for voltage range W (the "W" in the ordering code) and 1.7 V to 5.5 V for voltage range R (the "R" in the ordering code); decouple with 10 nF to 100 nF close to the VCC/VSS pins. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature | TSTG | -65 | 150 | °C | 27 | ||
| Ambient operating temperature | TAMR | -40 | 150 | °C | 27 | ||
| Voltage on Q pin | VO | -0.5 | V | 27 | |||
| Input voltage | VI | -0.5 | 6.5 | V | 27 | ||
| DC output current (Q = 0) | IOL | 5 | mA | Q = 0 | 27 | ||
| DC output current (Q = 1) | IOH | 5 | mA | Q = 1 | 27 | ||
| Supply voltage | VCC | -0.5 | 6.5 | V | 27 | ||
| Electrostatic pulse (Human Body Model) | VESD | 4000 | V | Human Body Model, AEC-Q100-002 | 27 | ||
| Write cycle endurance | Ncycle | 4e+06 | Write cycle | TA ≤ 25 °C, 1.7 V < VCC < 5.5 V | 28 | ||
| Write cycle endurance | Ncycle | 1.2e+06 | Write cycle | TA = 85 °C, 1.7 V < VCC < 5.5 V | 28 | ||
| Write cycle endurance | Ncycle | 600000 | Write cycle | TA = 125 °C, 1.7 V < VCC < 5.5 V | 28 | ||
| Supply voltage | VCC | 1.7 | 5.5 | V | 28 | ||
| Ambient operating temperature | TA | -40 | 125 | °C | 28 | ||
| Operating clock frequency | fC | 10 | MHz | VCC ≥ 2.5 V, capacitive load on Q pin ≤100pF | 28 | ||
| Operating clock frequency | fC | 5 | MHz | VCC ≥ 1.7 V, capacitive load on Q pin ≤100pF | 28 | ||
| Output capacitance (Q) | COUT | 8 | pF | VOUT = 0 V | 30 | ||
| Input capacitance | CIN | 6 | pF | VIN = 0 V | 30 | ||
| Input leakage current | ILI | 2 | µA | VIN = VSS or VCC | 30 | ||
| Output leakage current | ILO | 3 | µA | S = VCC, VOUT = VSS or VCC | 30 | ||
| Supply current (Read) | ICC | 2 | mA | VCC = 1.7 V, C = 0.1 VCC/0.9 VCC, Q = open, fC = 5 MHz | 30 | ||
| Supply current (Read) | ICC | 5 | mA | VCC = 5.5 V, fC = 20 MHz (footnote 1: -40 °C < t° < 85 °C), C = 0.1 VCC/0.9 VCC, Q = open | 30 | ||
| Supply current (Write) | ICC0 | 2 | mA | 1.7 V ≤ VCC < 5.5 V during tW, S = VCC (average value) | 30 | ||
| Supply current (Standby mode) | ICC1 | 1 | µA | t° = 85 °C, VCC = 1.7 V, S = VCC, VIN = VSS or VCC | 30 | ||
| Supply current (Standby mode) | ICC1 | 2 | µA | t° = 85 °C, VCC = 2.5 V, S = VCC, VIN = VSS or VCC | 30 | ||
| Supply current (Standby mode) | ICC1 | 3 | µA | t° = 85 °C, VCC = 5.5 V, S = VCC, VIN = VSS or VCC | 30 | ||
| Supply current (Standby mode) | ICC1 | 15 | µA | t° = 125 °C, VCC = 1.7 V, S = VCC, VIN = VSS or VCC | 30 | ||
| Supply current (Standby mode) | ICC1 | 20 | µA | t° = 125 °C, VCC = 5.5 V, S = VCC, VIN = VSS or VCC | 30 | ||
| Input low voltage | VIL | -0.45 | 0.25 | V | 1.7 V ≤ VCC < 2.5 V | 30 | |
| Input low voltage | VIL | -0.45 | 0.3 | V | 2.5 V ≤ VCC < 5.5 V | 30 | |
| Input high voltage | VIH | 0.75 | V | 1.7 V ≤ VCC < 2.5 V | 30 | ||
| Input high voltage | VIH | 0.7 | V | 2.5 V ≤ VCC < 5.5 V | 30 | ||
| Output low voltage | VOL | 0.3 | V | VCC = 1.7 V, IOL = 1 mA | 30 | ||
| Output low voltage | VOL | 0.4 | V | VCC ≥ 2.5 V, IOL = 2 mA | 30 | ||
| Output high voltage | VOH | 0.8 | V | VCC = 1.7 V, IOH = 1 mA | 30 | ||
| Internal reset threshold voltage | VRES | 0.5 | 1.5 | V | 30 | ||
| Clock frequency | fC | 5 | MHz | Test conditions specified in Table 10 | 31 | ||
| S active setup time | tSLCH | 60 | ns | Test conditions specified in Table 10 | 31 | ||
| S not active setup time | tSHCH | 60 | ns | Test conditions specified in Table 10 | 31 | ||
| S deselect time | tSHSL | 90 | ns | Test conditions specified in Table 10 | 31 | ||
| S active hold time | tCHSH | 60 | ns | Test conditions specified in Table 10 | 31 | ||
| S not active hold time | tCHSL | 60 | ns | Test conditions specified in Table 10 | 31 | ||
| Clock high time | tCH | 80 | ns | Test conditions specified in Table 10 | 31 | ||
| Clock low time | tCL | 80 | ns | Test conditions specified in Table 10 | 31 | ||
| Clock rise time | tCLCH | 2 | µs | Test conditions specified in Table 10 | 31 | ||
| Clock fall time | tCHCL | 2 | µs | Test conditions specified in Table 10 | 31 | ||
| Data in setup time | tDVCH | 20 | ns | Test conditions specified in Table 10 | 31 | ||
| Data in hold time | tCHDX | 20 | ns | Test conditions specified in Table 10 | 31 | ||
| Clock low hold time after HOLD not active | tHHCH | 60 | ns | Test conditions specified in Table 10 | 31 | ||
| Clock low hold time after HOLD active | tHLCH | 60 | ns | Test conditions specified in Table 10 | 31 | ||
| Clock low to output disable time (S high) | tSHQZ | 80 | ns | Test conditions specified in Table 10 | 31 | ||
| Clock low to output valid | tCLQV | 80 | ns | Test conditions specified in Table 10 | 31 | ||
| Output hold time | tCLQX | 0 | ns | Test conditions specified in Table 10 | 31 | ||
| Output rise time | tQLQH | 20 | ns | Test conditions specified in Table 10 | 31 | ||
| Output fall time | tQHQL | 20 | ns | Test conditions specified in Table 10 | 31 | ||
| HOLD high to output valid | tHHQV | 80 | ns | Test conditions specified in Table 10 | 31 | ||
| HOLD low to output high-Z | tHLQZ | 80 | ns | Test conditions specified in Table 10 | 31 | ||
| Write time | tW | 4 | ms | Test conditions specified in Table 10 | 31 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | TLEAD Lead temperature during soldering See note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST ECOPACK® | 27 |
CAD (KiCad official)
- Symbol:
M95020-DRDW3TP - Footprint:
Package_SO:TSSOP-8_4.4x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
m95020-drdw3tp-etched.step/m95020-drdw3tp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m95020-drdw3tp.step/m95020-drdw3tp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (41 pp, sha256
295ed282405abcac, retrieved 2026-11-12, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# M95020-DRDW3TP
> The maker sells this part only as M95020-DRDW3TP/K (ST ordering information scheme: "T = Tape and reel packing", "/K = Manufacturing technology code"; the bare code lacks the process letter (Table 18, p.39)). The DigiKey and Mouser numbers on this page are for M95020-DRDW3TP/K.
**STMicroelectronics** · EEPROM · TSSOP-8
M95020-DRDW3TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ~{S} | input | Chip Select: driving it low selects the device and starts communication, driving it high deselects the device and puts Q in high impedance; it should follow VCC at power-up, for example through a pull-up resistor. |
| 2 | Q | tri_state | Serial Data output: shifts data out on the falling edge of Serial Clock (C), MSB first, during a Read, and is high impedance in all other cases. |
| 3 | ~{W} | input | Write Protect (active low): write-protects the Status Register, and a low level stops the WRSR and WRITE instructions from being executed. |
| 4 | VSS | power_in | Ground: the reference for all signals, including the VCC supply voltage. |
| 5 | D | input | Serial Data input: receives instructions, addresses and data to be written, latched on the rising edge of Serial Clock (C), MSB first. |
| 6 | C | input | Serial Clock: synchronizes the serial interface, with data on D latched on the rising edge and data on Q changing after the falling edge. |
| 7 | ~{HOLD} | input | Hold (active low): pauses serial communication without deselecting the device; Q is high impedance and D and C are Don't Care during Hold, and the device must be selected (S low) to start it. |
| 8 | VCC | power_in | Supply voltage: 2.5 V to 5.5 V for voltage range W (the "W" in the ordering code) and 1.7 V to 5.5 V for voltage range R (the "R" in the ordering code); decouple with 10 nF to 100 nF close to the VCC/VSS pins. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature | TSTG | -65 | | 150 | °C | | 27 |
| Ambient operating temperature | TAMR | -40 | | 150 | °C | | 27 |
| Voltage on Q pin | VO | -0.5 | | | V | | 27 |
| Input voltage | VI | -0.5 | | 6.5 | V | | 27 |
| DC output current (Q = 0) | IOL | | | 5 | mA | Q = 0 | 27 |
| DC output current (Q = 1) | IOH | | | 5 | mA | Q = 1 | 27 |
| Supply voltage | VCC | -0.5 | | 6.5 | V | | 27 |
| Electrostatic pulse (Human Body Model) | VESD | | | 4000 | V | Human Body Model, AEC-Q100-002 | 27 |
| Write cycle endurance | Ncycle | | | 4e+06 | Write cycle | TA ≤ 25 °C, 1.7 V < VCC < 5.5 V | 28 |
| Write cycle endurance | Ncycle | | | 1.2e+06 | Write cycle | TA = 85 °C, 1.7 V < VCC < 5.5 V | 28 |
| Write cycle endurance | Ncycle | | | 600000 | Write cycle | TA = 125 °C, 1.7 V < VCC < 5.5 V | 28 |
| Supply voltage | VCC | 1.7 | | 5.5 | V | | 28 |
| Ambient operating temperature | TA | -40 | | 125 | °C | | 28 |
| Operating clock frequency | fC | | | 10 | MHz | VCC ≥ 2.5 V, capacitive load on Q pin ≤100pF | 28 |
| Operating clock frequency | fC | | | 5 | MHz | VCC ≥ 1.7 V, capacitive load on Q pin ≤100pF | 28 |
| Output capacitance (Q) | COUT | | | 8 | pF | VOUT = 0 V | 30 |
| Input capacitance | CIN | | | 6 | pF | VIN = 0 V | 30 |
| Input leakage current | ILI | | | 2 | µA | VIN = VSS or VCC | 30 |
| Output leakage current | ILO | | | 3 | µA | S = VCC, VOUT = VSS or VCC | 30 |
| Supply current (Read) | ICC | | | 2 | mA | VCC = 1.7 V, C = 0.1 VCC/0.9 VCC, Q = open, fC = 5 MHz | 30 |
| Supply current (Read) | ICC | | | 5 | mA | VCC = 5.5 V, fC = 20 MHz (footnote 1: -40 °C < t° < 85 °C), C = 0.1 VCC/0.9 VCC, Q = open | 30 |
| Supply current (Write) | ICC0 | | | 2 | mA | 1.7 V ≤ VCC < 5.5 V during tW, S = VCC (average value) | 30 |
| Supply current (Standby mode) | ICC1 | | | 1 | µA | t° = 85 °C, VCC = 1.7 V, S = VCC, VIN = VSS or VCC | 30 |
| Supply current (Standby mode) | ICC1 | | | 2 | µA | t° = 85 °C, VCC = 2.5 V, S = VCC, VIN = VSS or VCC | 30 |
| Supply current (Standby mode) | ICC1 | | | 3 | µA | t° = 85 °C, VCC = 5.5 V, S = VCC, VIN = VSS or VCC | 30 |
| Supply current (Standby mode) | ICC1 | | | 15 | µA | t° = 125 °C, VCC = 1.7 V, S = VCC, VIN = VSS or VCC | 30 |
| Supply current (Standby mode) | ICC1 | | | 20 | µA | t° = 125 °C, VCC = 5.5 V, S = VCC, VIN = VSS or VCC | 30 |
| Input low voltage | VIL | -0.45 | | 0.25 | V | 1.7 V ≤ VCC < 2.5 V | 30 |
| Input low voltage | VIL | -0.45 | | 0.3 | V | 2.5 V ≤ VCC < 5.5 V | 30 |
| Input high voltage | VIH | 0.75 | | | V | 1.7 V ≤ VCC < 2.5 V | 30 |
| Input high voltage | VIH | 0.7 | | | V | 2.5 V ≤ VCC < 5.5 V | 30 |
| Output low voltage | VOL | | | 0.3 | V | VCC = 1.7 V, IOL = 1 mA | 30 |
| Output low voltage | VOL | | | 0.4 | V | VCC ≥ 2.5 V, IOL = 2 mA | 30 |
| Output high voltage | VOH | 0.8 | | | V | VCC = 1.7 V, IOH = 1 mA | 30 |
| Internal reset threshold voltage | VRES | 0.5 | | 1.5 | V | | 30 |
| Clock frequency | fC | | | 5 | MHz | Test conditions specified in Table 10 | 31 |
| S active setup time | tSLCH | 60 | | | ns | Test conditions specified in Table 10 | 31 |
| S not active setup time | tSHCH | 60 | | | ns | Test conditions specified in Table 10 | 31 |
| S deselect time | tSHSL | 90 | | | ns | Test conditions specified in Table 10 | 31 |
| S active hold time | tCHSH | 60 | | | ns | Test conditions specified in Table 10 | 31 |
| S not active hold time | tCHSL | 60 | | | ns | Test conditions specified in Table 10 | 31 |
| Clock high time | tCH | 80 | | | ns | Test conditions specified in Table 10 | 31 |
| Clock low time | tCL | 80 | | | ns | Test conditions specified in Table 10 | 31 |
| Clock rise time | tCLCH | | | 2 | µs | Test conditions specified in Table 10 | 31 |
| Clock fall time | tCHCL | | | 2 | µs | Test conditions specified in Table 10 | 31 |
| Data in setup time | tDVCH | 20 | | | ns | Test conditions specified in Table 10 | 31 |
| Data in hold time | tCHDX | 20 | | | ns | Test conditions specified in Table 10 | 31 |
| Clock low hold time after HOLD not active | tHHCH | 60 | | | ns | Test conditions specified in Table 10 | 31 |
| Clock low hold time after HOLD active | tHLCH | 60 | | | ns | Test conditions specified in Table 10 | 31 |
| Clock low to output disable time (S high) | tSHQZ | | | 80 | ns | Test conditions specified in Table 10 | 31 |
| Clock low to output valid | tCLQV | | | 80 | ns | Test conditions specified in Table 10 | 31 |
| Output hold time | tCLQX | 0 | | | ns | Test conditions specified in Table 10 | 31 |
| Output rise time | tQLQH | | | 20 | ns | Test conditions specified in Table 10 | 31 |
| Output fall time | tQHQL | | | 20 | ns | Test conditions specified in Table 10 | 31 |
| HOLD high to output valid | tHHQV | | | 80 | ns | Test conditions specified in Table 10 | 31 |
| HOLD low to output high-Z | tHLQZ | | | 80 | ns | Test conditions specified in Table 10 | 31 |
| Write time | tW | | | 4 | ms | Test conditions specified in Table 10 | 31 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | TLEAD Lead temperature during soldering See note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST ECOPACK® | 27 |
## CAD (KiCad official)
- Symbol: `M95020-DRDW3TP`
- Footprint: `Package_SO:TSSOP-8_4.4x3mm_P0.65mm`
- 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files: `m95020-drdw3tp-etched.step` / `m95020-drdw3tp-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `m95020-drdw3tp.step` / `m95020-drdw3tp.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8589828487566823424) (41 pp, sha256 `295ed282405abcac`, retrieved 2026-11-12, tier: lcsc)
- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/m95020-drdw3tp-datasheet.pdf)