← Commit history

Initial commit: component/m93c86-wmn6tp

Ray ·f69e4c9ece ·
2 files changed +185
README.mdadded+44
@@ -0,0 +1,44 @@+# M93C86-WMN6TP++**STMicroelectronics** · EEPROM · SOIC-8++M93C86-WMN6TP from STMicroelectronics, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | S | input | Chip Select input; a rising edge on S (with C low) initiates an instruction; S must be driven, not left floating (pull-down resistor recommended) especially during power-up; also used to read READY/BUSY status after a write/erase cycle. |+| 2 | C | input | Serial Clock input; instruction bits, address and data are read on Serial Data Input on the rising edge of C; clock rate is DC to 2 MHz (M93Cx6-W / M93Cx6-R with process letter K) or DC to 1 MHz (other M93Cx6-R devices). |+| 3 | D | input | Serial Data Input; carries the start bit, op-code, address and write data of each instruction, sampled on the rising edge of Serial Clock (C). |+| 4 | Q | tri_state | Serial Data Output; outputs read data and the READY/BUSY status; high impedance when the device is not selected, driven only when S is high and the device is selected. |+| 5 | VSS | power_in | Ground reference pin for the device. |+| 6 | ORG | input | Organization Select input; unconnected or tied to VCC selects x16 (word) organization, tied to VSS (ground) selects x8 (byte) organization; in Standby mode ORG should be tied to VSS or VCC to minimize standby current. |+| 7 | DU | unconnected | Don't Use pin, reserved by STMicroelectronics for test sequences; does not affect normal device operation and may be left unconnected or tied to VCC or VSS (referenced as pin7 in the standby-current test conditions). |+| 8 | VCC | power_in | Supply voltage input, 2.5 V to 5.5 V for M93Cx6-W or 1.8 V to 5.5 V for M93Cx6-R; must remain stable and valid until completion of any write cycle; decoupling capacitor of 10 nF to 100 nF recommended close to VCC/VSS pins. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | SOIC-8 |+| Category | Memory |+| Pins | 8 |++## CAD (KiCad official)++- Symbol: `M93C86-WMN6TP`+- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`+- 3D model: SOIC-8 (KiCad packages3D, STEP)+- 3D model files: `m93c86-wmn6tp-etched.step` / `m93c86-wmn6tp-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `m93c86-wmn6tp.step` / `m93c86-wmn6tp.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588879906566778880) (35 pp, sha256 `7b1f76e6c602697a`, retrieved 2026-09-22, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/m93c86-wmn6tp-datasheet.pdf)
page.jsonadded+141
@@ -0,0 +1,141 @@+{+  "slug": "m93c86-wmn6tp",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics EEPROM, SOIC-8. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "memory",+    "m93c86-wmn6tp",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "m93c86-wmn6tp.kicad_sym",+    "m93c86-wmn6tp.kicad_mod",+    "m93c86-wmn6tp.glb",+    "m93c86-wmn6tp.step",+    "m93c86-wmn6tp.lbr",+    "docs/hero.png",+    "docs/m93c86-wmn6tp-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "M93C86-WMN6TP",+    "manufacturer": "STMicroelectronics",+    "package": "SOIC-8",+    "pin_count": 8,+    "category": "Memory",+    "subcategory": "EEPROM",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588879906566778880",+    "parts": {+      "symbol": "m93c86-wmn6tp.kicad_sym",+      "footprint": "m93c86-wmn6tp.kicad_mod",+      "model_3d": "m93c86-wmn6tp-etched.glb",+      "model_3d_plain": "m93c86-wmn6tp.glb",+      "model_3d_step": "m93c86-wmn6tp-etched.step",+      "model_3d_step_plain": "m93c86-wmn6tp.step",+      "lbr": "m93c86-wmn6tp.lbr"+    },+    "distributor_links": {+      "lcsc": "C111883"+    },+    "pins": [+      {+        "number": "1",+        "name": "S",+        "type": "input",+        "description": "Chip Select input; a rising edge on S (with C low) initiates an instruction; S must be driven, not left floating (pull-down resistor recommended) especially during power-up; also used to read READY/BUSY status after a write/erase cycle."+      },+      {+        "number": "2",+        "name": "C",+        "type": "input",+        "description": "Serial Clock input; instruction bits, address and data are read on Serial Data Input on the rising edge of C; clock rate is DC to 2 MHz (M93Cx6-W / M93Cx6-R with process letter K) or DC to 1 MHz (other M93Cx6-R devices)."+      },+      {+        "number": "3",+        "name": "D",+        "type": "input",+        "description": "Serial Data Input; carries the start bit, op-code, address and write data of each instruction, sampled on the rising edge of Serial Clock (C)."+      },+      {+        "number": "4",+        "name": "Q",+        "type": "tri_state",+        "description": "Serial Data Output; outputs read data and the READY/BUSY status; high impedance when the device is not selected, driven only when S is high and the device is selected."+      },+      {+        "number": "5",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground reference pin for the device."+      },+      {+        "number": "6",+        "name": "ORG",+        "type": "input",+        "description": "Organization Select input; unconnected or tied to VCC selects x16 (word) organization, tied to VSS (ground) selects x8 (byte) organization; in Standby mode ORG should be tied to VSS or VCC to minimize standby current."+      },+      {+        "number": "7",+        "name": "DU",+        "type": "unconnected",+        "description": "Don't Use pin, reserved by STMicroelectronics for test sequences; does not affect normal device operation and may be left unconnected or tied to VCC or VSS (referenced as pin7 in the standby-current test conditions)."+      },+      {+        "number": "8",+        "name": "VCC",+        "type": "power_in",+        "description": "Supply voltage input, 2.5 V to 5.5 V for M93Cx6-W or 1.8 V to 5.5 V for M93Cx6-R; must remain stable and valid until completion of any write cycle; decoupling capacitor of 10 nF to 100 nF recommended close to VCC/VSS pins."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 35,+        "cost_usd": 0.2151,+        "at": "2026-09-22T23:07:55"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588879906566778880",+        "pages": 35,+        "sha256": "7b1f76e6c602697a",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 8,+        "described": 8,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file