← Commit history

m93c66-rmn3tp: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·cd00f7c9e4 · ·parent f8a3f9a
1 file changed +75−1
page.json+75−1
@@ -33,5 +33,79 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "M93C66-RMN3TP",+    "manufacturer": "STMicroelectronics",+    "package": "SOIC-8",+    "pin_count": 8,+    "category": "EEPROM",+    "datasheet": "https://www.st.com/resource/en/datasheet/m93c66-rmn3tp.pdf",+    "parts": {+      "symbol": "m93c66-rmn3tp.kicad_sym",+      "footprint": "m93c66-rmn3tp.kicad_mod",+      "model_3d": "m93c66-rmn3tp-etched.glb",+      "model_3d_plain": "m93c66-rmn3tp.glb",+      "model_3d_step": "m93c66-rmn3tp-etched.step",+      "model_3d_step_plain": "m93c66-rmn3tp.step",+      "lbr": "m93c66-rmn3tp.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "S",+        "type": "input",+        "description": "Chip Select input. Active High; enables the device and frames each MICROWIRE instruction. Must be pulled to VSS at power-up (recommended external pull-down, typ. 100 kΩ) to prevent inadvertent selection."+      },+      {+        "number": "2",+        "name": "C",+        "type": "input",+        "description": "Serial Clock input. Synchronous clock driven by the bus master; latches D on rising edges and shifts Q out. Maximum clock rate 2 MHz. External pull-down recommended so that C is low when S is deselected (meets tSLCH)."+      },+      {+        "number": "3",+        "name": "D",+        "type": "input",+        "description": "Serial Data input. Carries the start bit, op-code, address, and write data for MICROWIRE instructions; sampled on the rising edge of C while S is High."+      },+      {+        "number": "4",+        "name": "Q",+        "type": "tri_state",+        "description": "Serial Data output. Push-pull output that shifts read data out on the rising edge of C; also drives the READY/BUSY status during a programming cycle when S is High. Goes high-impedance when the device is deselected."+      },+      {+        "number": "5",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground reference (0 V). Common return for supply and all logic signals."+      },+      {+        "number": "6",+        "name": "ORG",+        "type": "input",+        "description": "Organization Select input. Tie to VCC (or leave open - internally pulled up) to configure the array as 256 x 16; tie to VSS to configure as 512 x 8. Must be driven to VCC or VSS (not left mid-rail) in Standby to minimize ICC."+      },+      {+        "number": "7",+        "name": "DU",+        "type": "unconnected",+        "description": "Don't Use. Reserved for STMicroelectronics test purposes and must not be used in normal operation. May be left unconnected or tied to VCC or VSS."+      },+      {+        "number": "8",+        "name": "VCC",+        "type": "power_in",+        "description": "Positive supply input, 1.8 V to 5.5 V. Decouple to VSS with a 10-100 nF capacitor close to the pin; must remain stable through the internal write cycle (tW)."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}