main
Ray
Publish 0.1.0
a7dbfb4
M24SR04-YDW6T
STMicroelectronics · RFID ICs · TSSOP-8
M24SR04-YDW6T from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RF disable | input | Input that disables RF communication; an internal pull-down holds it low when VCC is below POR or unconnected, an external pull-down is required when VCC is above POR, and it must not be left floating in Dual interface mode. |
| 2 | AC0 | passive | Antenna coil connection, to be used exclusively for the external coil with no other DC or AC path connected. |
| 3 | AC1 | passive | Antenna coil connection, to be used exclusively for the external coil with no other DC or AC path connected. |
| 4 | VSS | power_in | Ground, the reference for the VCC supply voltage for all pads, even AC0 and AC1. |
| 5 | SDA | bidirectional | Open-drain serial data I/O for the I2C interface that needs a pull-up resistor to VCC. |
| 6 | SCL | input | Serial clock input that strobes all data in and out of the device on the I2C interface. |
| 7 | GPO | output | Configurable open-drain general purpose output (Session Open by default) that requires an external pull-up greater than 4.7 kOhm. |
| 8 | VCC | power_in | Supply voltage pin of 2.7 V to 5.5 V for grade Y, with a rise time no faster than 1 V/us and decoupling recommended close to the VCC/VSS pins. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | RF And Wireless |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature (UFDFPN8, SO8, TSSOP8) | TSTG | -65 | 150 | °C | 67 | ||
| Ambient operating temperature for grade 6 | TA | -40 | 85 | °C | Grade 6 | 67 | |
| I2C input or output range and GPO | VIO | -0.5 | 6.5 | V | 67 | ||
| RF supply current | ICC | 100 | mA | AC0-AC1; based on characterization, not tested in production | 67 | ||
| RF input voltage amplitude between AC0 and AC1 | VMAX_1 | 10 | V | GND pad left floating; based on characterization, not tested in production | 67 | ||
| AC voltage between AC0 and GND, or AC1 and GND | VMAX_2 | -0.5 | 4.5 | V | AC0-GND or AC1-GND; based on characterization, not tested in production | 67 | |
| Electrostatic discharge voltage (human body model) | VESD | 1000 | V | AC0-AC1; AEC-Q100-002 | 67 | ||
| Electrostatic discharge voltage (human body model) | VESD | 3500 | V | Other pads; AEC-Q100-002 | 67 | ||
| Supply voltage range Y | VCC | 2.7 | 5.5 | V | Grade Y | 68 | |
| Ambient operating temperature for grade 6 | TA | -40 | 85 | °C | Grade 6 | 68 | |
| Input rise and fall times | tr, tf | 50 | ns | 68 | |||
| Input capacitance (SDA) | CIN | 8 | pF | 68 | |||
| Input capacitance (other pins) | CIN | 6 | pF | 68 | |||
| Pulse width ignored (input filter on SCL and SDA) | tNS | 80 | ns | Characterized only, not tested in production | 68 | ||
| Input leakage current (SCL, SDA) | ILI | -2 | 2 | µA | VIN = VSS or VCC; device in Standby mode | 69 | |
| Output leakage current (SDA) | ILO | -2 | 2 | µA | SDA in Hi-Z, external voltage applied on SDA: VSS or VCC | 69 | |
| Standby power mode supply current | ICC0 | 30 | µA | VCC = 3.3 V, with RF ON | 69 | ||
| Standby power mode supply current | ICC0 | 5 | µA | VCC = 3.3 V, with RF OFF | 69 | ||
| Supply current (I2C session open) | ICC1 | 150 | µA | VCC = 3.3 V, with RF ON | 69 | ||
| Supply current (read binary) | ICC2 | 250 | µA | VCC = 3.3 V (fC = 1 MHz), with RF ON | 69 | ||
| Supply current (read binary) | ICC2 | 200 | µA | VCC = 3.3 V (fC = 1 MHz), with RF OFF | 69 | ||
| Supply current (update binary) | ICC3 | 550 | µA | VCC = 3.3 V (fC = 1 MHz), with RF ON | 69 | ||
| Supply current (update binary) | ICC3 | 500 | µA | VCC = 3.3 V (fC = 1 MHz), with RF OFF | 69 | ||
| Input low voltage (SDA, SCL) | VIL | -0.45 | V | VCC = 2.7 V (grade Y); VCC = 5.5 V | 69 | ||
| Input high voltage (SDA, SCL) | VIH | 6.5 | V | VCC = 2.7 V (grade Y); VCC = 5.5 V | 69 | ||
| Input low voltage (RF disable) | VIL | 0.45 | V | VCC = 2.7 V (grade Y); VCC = 5.5 V | 69 | ||
| Input high voltage (RF disable) | VIH | 1.4 | V | VCC = 2.7 V (grade Y); VCC = 5.5 V | 69 | ||
| Output low voltage (SDA) | VOL | 0.4 | V | IOL = 3 mA, VCC = 5.5 V | 69 | ||
| Output low voltage (GPO) | VOL | 0.4 | V | IOL = 1 mA, VCC = 2.7 V (grade Y) to VCC = 5.5 V | 69 | ||
| Write cycle endurance | Ncycle | 1e+06 | TA ≤ 25 °C, VCC(min) < VCC < VCC(max) | 77 | |||
| Write cycle endurance | Ncycle | 600000 | TA ≤ 85 °C, VCC(min) < VCC < VCC(max) | 77 | |||
| External RF signal frequency | fC | 13.553 | 13.56 | 13.567 | MHz | 78 | |
| Operating field according to ISO | H_ISO | 1500 | 7500 | mA/m | TA = 0 °C to 50 °C | 78 | |
| Operating field in extended temperature range | H_Extended | 500 | 7500 | mA/m | TA = -40 °C to 85 °C | 78 | |
| 100% carrier modulation index | MI | 90 | 100 | % | MI=(A-B)/(A+B) | 78 | |
| RF write time (including internal Verify) for one page | Wt | 6 | ms | 78 | |||
| RF OFF time | tRF_OFF | 5 | ms | Chip reset | 78 | ||
| Minimum time from carrier generation to first data | tMIN CD | 5 | ms | From H-field min | 78 | ||
| Clock frequency | fC | 0.05 | 400 | kHz | Test conditions specified in Table 74 | 70 | |
| Clock pulse width high | tCHCL | 0.6 | 20000 | µs | Test conditions specified in Table 74 | 70 | |
| Clock pulse width low | tCLCH | 1.3 | 20000 | µs | Test conditions specified in Table 74 | 70 | |
| SDA (out) fall time | tDL1DL2 | 20 | 300 | ns | Test conditions specified in Table 74 | 70 | |
| Data in set up time | tDXCX | 100 | ns | Test conditions specified in Table 74 | 70 | ||
| Data out hold time | tCLQX | 100 | ns | Test conditions specified in Table 74 | 70 | ||
| Clock low to next data valid (access time) | tCLQV | 900 | ns | Test conditions specified in Table 74 | 70 | ||
| Start condition set up time | tCHDX | 600 | ns | Test conditions specified in Table 74 | 70 | ||
| Start condition hold time | tDLCL | 600 | ns | Test conditions specified in Table 74 | 70 | ||
| Stop condition set up time | tCHDH | 600 | ns | Test conditions specified in Table 74 | 70 | ||
| Time between Stop condition and next Start condition | tDHDL | 1300 | ns | Test conditions specified in Table 74 | 70 | ||
| I2C write time in one page | tW | 5 | ms | Test conditions specified in Table 74 | 70 | ||
| I2C write time up to 246 bytes | tW | 90 | ms | Test conditions specified in Table 74 | 70 |
CAD (KiCad official)
- Symbol:
M24SR04-YDW6T - Footprint:
Package_SO:TSSOP-8_4.4x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
m24sr04-ydw6t-2-etched.step/m24sr04-ydw6t-2-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m24sr04-ydw6t-2.step/m24sr04-ydw6t-2.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (89 pp, sha256
d434a54171393933, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# M24SR04-YDW6T
**STMicroelectronics** · RFID ICs · TSSOP-8
M24SR04-YDW6T from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RF disable | input | Input that disables RF communication; an internal pull-down holds it low when VCC is below POR or unconnected, an external pull-down is required when VCC is above POR, and it must not be left floating in Dual interface mode. |
| 2 | AC0 | passive | Antenna coil connection, to be used exclusively for the external coil with no other DC or AC path connected. |
| 3 | AC1 | passive | Antenna coil connection, to be used exclusively for the external coil with no other DC or AC path connected. |
| 4 | VSS | power_in | Ground, the reference for the VCC supply voltage for all pads, even AC0 and AC1. |
| 5 | SDA | bidirectional | Open-drain serial data I/O for the I2C interface that needs a pull-up resistor to VCC. |
| 6 | SCL | input | Serial clock input that strobes all data in and out of the device on the I2C interface. |
| 7 | GPO | output | Configurable open-drain general purpose output (Session Open by default) that requires an external pull-up greater than 4.7 kOhm. |
| 8 | VCC | power_in | Supply voltage pin of 2.7 V to 5.5 V for grade Y, with a rise time no faster than 1 V/us and decoupling recommended close to the VCC/VSS pins. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | RF And Wireless |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage temperature (UFDFPN8, SO8, TSSOP8) | TSTG | -65 | | 150 | °C | | 67 |
| Ambient operating temperature for grade 6 | TA | -40 | | 85 | °C | Grade 6 | 67 |
| I2C input or output range and GPO | VIO | -0.5 | | 6.5 | V | | 67 |
| RF supply current | ICC | | | 100 | mA | AC0-AC1; based on characterization, not tested in production | 67 |
| RF input voltage amplitude between AC0 and AC1 | VMAX_1 | | | 10 | V | GND pad left floating; based on characterization, not tested in production | 67 |
| AC voltage between AC0 and GND, or AC1 and GND | VMAX_2 | -0.5 | | 4.5 | V | AC0-GND or AC1-GND; based on characterization, not tested in production | 67 |
| Electrostatic discharge voltage (human body model) | VESD | | | 1000 | V | AC0-AC1; AEC-Q100-002 | 67 |
| Electrostatic discharge voltage (human body model) | VESD | | | 3500 | V | Other pads; AEC-Q100-002 | 67 |
| Supply voltage range Y | VCC | 2.7 | | 5.5 | V | Grade Y | 68 |
| Ambient operating temperature for grade 6 | TA | -40 | | 85 | °C | Grade 6 | 68 |
| Input rise and fall times | tr, tf | | | 50 | ns | | 68 |
| Input capacitance (SDA) | CIN | | | 8 | pF | | 68 |
| Input capacitance (other pins) | CIN | | | 6 | pF | | 68 |
| Pulse width ignored (input filter on SCL and SDA) | tNS | | | 80 | ns | Characterized only, not tested in production | 68 |
| Input leakage current (SCL, SDA) | ILI | -2 | | 2 | µA | VIN = VSS or VCC; device in Standby mode | 69 |
| Output leakage current (SDA) | ILO | -2 | | 2 | µA | SDA in Hi-Z, external voltage applied on SDA: VSS or VCC | 69 |
| Standby power mode supply current | ICC0 | | | 30 | µA | VCC = 3.3 V, with RF ON | 69 |
| Standby power mode supply current | ICC0 | | | 5 | µA | VCC = 3.3 V, with RF OFF | 69 |
| Supply current (I2C session open) | ICC1 | | | 150 | µA | VCC = 3.3 V, with RF ON | 69 |
| Supply current (read binary) | ICC2 | | | 250 | µA | VCC = 3.3 V (fC = 1 MHz), with RF ON | 69 |
| Supply current (read binary) | ICC2 | | | 200 | µA | VCC = 3.3 V (fC = 1 MHz), with RF OFF | 69 |
| Supply current (update binary) | ICC3 | | | 550 | µA | VCC = 3.3 V (fC = 1 MHz), with RF ON | 69 |
| Supply current (update binary) | ICC3 | | | 500 | µA | VCC = 3.3 V (fC = 1 MHz), with RF OFF | 69 |
| Input low voltage (SDA, SCL) | VIL | -0.45 | | | V | VCC = 2.7 V (grade Y); VCC = 5.5 V | 69 |
| Input high voltage (SDA, SCL) | VIH | | | 6.5 | V | VCC = 2.7 V (grade Y); VCC = 5.5 V | 69 |
| Input low voltage (RF disable) | VIL | | | 0.45 | V | VCC = 2.7 V (grade Y); VCC = 5.5 V | 69 |
| Input high voltage (RF disable) | VIH | 1.4 | | | V | VCC = 2.7 V (grade Y); VCC = 5.5 V | 69 |
| Output low voltage (SDA) | VOL | | | 0.4 | V | IOL = 3 mA, VCC = 5.5 V | 69 |
| Output low voltage (GPO) | VOL | | | 0.4 | V | IOL = 1 mA, VCC = 2.7 V (grade Y) to VCC = 5.5 V | 69 |
| Write cycle endurance | Ncycle | | | 1e+06 | | TA ≤ 25 °C, VCC(min) < VCC < VCC(max) | 77 |
| Write cycle endurance | Ncycle | | | 600000 | | TA ≤ 85 °C, VCC(min) < VCC < VCC(max) | 77 |
| External RF signal frequency | fC | 13.553 | 13.56 | 13.567 | MHz | | 78 |
| Operating field according to ISO | H_ISO | 1500 | | 7500 | mA/m | TA = 0 °C to 50 °C | 78 |
| Operating field in extended temperature range | H_Extended | 500 | | 7500 | mA/m | TA = -40 °C to 85 °C | 78 |
| 100% carrier modulation index | MI | 90 | | 100 | % | MI=(A-B)/(A+B) | 78 |
| RF write time (including internal Verify) for one page | Wt | | | 6 | ms | | 78 |
| RF OFF time | tRF_OFF | | | 5 | ms | Chip reset | 78 |
| Minimum time from carrier generation to first data | tMIN CD | | | 5 | ms | From H-field min | 78 |
| Clock frequency | fC | 0.05 | | 400 | kHz | Test conditions specified in Table 74 | 70 |
| Clock pulse width high | tCHCL | 0.6 | | 20000 | µs | Test conditions specified in Table 74 | 70 |
| Clock pulse width low | tCLCH | 1.3 | | 20000 | µs | Test conditions specified in Table 74 | 70 |
| SDA (out) fall time | tDL1DL2 | 20 | | 300 | ns | Test conditions specified in Table 74 | 70 |
| Data in set up time | tDXCX | 100 | | | ns | Test conditions specified in Table 74 | 70 |
| Data out hold time | tCLQX | 100 | | | ns | Test conditions specified in Table 74 | 70 |
| Clock low to next data valid (access time) | tCLQV | | | 900 | ns | Test conditions specified in Table 74 | 70 |
| Start condition set up time | tCHDX | 600 | | | ns | Test conditions specified in Table 74 | 70 |
| Start condition hold time | tDLCL | 600 | | | ns | Test conditions specified in Table 74 | 70 |
| Stop condition set up time | tCHDH | 600 | | | ns | Test conditions specified in Table 74 | 70 |
| Time between Stop condition and next Start condition | tDHDL | 1300 | | | ns | Test conditions specified in Table 74 | 70 |
| I2C write time in one page | tW | | | 5 | ms | Test conditions specified in Table 74 | 70 |
| I2C write time up to 246 bytes | tW | | | 90 | ms | Test conditions specified in Table 74 | 70 |
## CAD (KiCad official)
- Symbol: `M24SR04-YDW6T`
- Footprint: `Package_SO:TSSOP-8_4.4x3mm_P0.65mm`
- 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files: `m24sr04-ydw6t-2-etched.step` / `m24sr04-ydw6t-2-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `m24sr04-ydw6t-2.step` / `m24sr04-ydw6t-2.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588931376653471744) (89 pp, sha256 `d434a54171393933`, retrieved 2026-11-10, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text+vision), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/m24sr04-ydw6t-2-datasheet.pdf)