Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

M24SR04-YDW6T

The maker sells this part only as M24SR04-YDW6T/2 (ST ordering information scheme (Table 88, p.84): "T = Tape and reel packing", "Capacitance /2 = 25 pF", the only capacitance option listed). The DigiKey and Mouser numbers on this page are for M24SR04-YDW6T/2.

STMicroelectronics · RFID ICs · TSSOP-8

M24SR04-YDW6T from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RF disable input Input that disables RF communication; an internal pull-down holds it low when VCC is below the POR level or not connected, an external pull-down is required when VCC is above POR, and it must not be left floating in Dual interface mode.
2 AC0 passive Antenna coil connection used exclusively for the external coil; no other DC or AC path should be connected to it.
3 AC1 passive Antenna coil connection used exclusively for the external coil; no other DC or AC path should be connected to it.
4 VSS power_in Ground, the reference for the VCC supply voltage for all pads, including AC0 and AC1.
5 SDA bidirectional I2C serial data, an open-drain bidirectional line that needs a pull-up resistor to VCC.
6 SCL input I2C serial clock input that strobes all data in and out of the device; a pull-up to VCC is needed only if the bus master has an open-drain output.
7 GPO output Configurable open-drain general purpose output (Session Open by default) that requires an external pull-up greater than 4.7 kOhm.
8 VCC power_in Supply voltage input, 2.7 V to 5.5 V for grade Y, with 10 nF and 100 pF decoupling capacitors recommended close to the VCC/VSS pins.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package TSSOP-8
Category RF And Wireless
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Ambient operating temperature for grade 6 TA -40 85 °C 67
Storage temperature UFDFPN8, SO8, TSSOP8 TSTG -65 150 °C 67
I2C input or output range and GPO VIO -0.5 6.5 V 67
RF supply current ICC 100 mA AC0 - AC1 67
RF input voltage amplitude VMAX_1 10 V between AC0 and AC1, GND pad left floating 67
AC voltage VMAX_2 -0.5 4.5 V VAC0-GND or VAC1-GND 67
Electrostatic discharge voltage (human body model) VESD 1000 V AC0-AC1 67
Electrostatic discharge voltage (human body model) VESD 3500 V Other pads 67
Supply voltage range Y VCC 2.7 5.5 V 68
Ambient operating temperature for grade 6 TA -40 85 °C 68
Input capacitance (SDA) CIN 8 pF 68
Input capacitance (other pins) CIN 6 pF 68
Pulse width ignored (input filter on SCL and SDA) tNS 80 ns Input filter on SCL and SDA 68
Input leakage current (SCL, SDA) ILI -2 2 µA VIN = VSS or VCC; device in Standby mode 69
Output leakage current ILO -2 2 µA SDA in Hi-Z, external voltage applied on SDA: VSS or VCC 69
Standby power mode supply current ICC0 30 µA VCC = 3.3 V, with RF ON 69
Standby power mode supply current ICC0 5 µA VCC = 3.3 V, with RF OFF 69
Supply current (I2C session open) ICC1 150 µA VCC = 3.3 V, with RF ON 69
Supply current (read binary) ICC2 250 µA VCC = 3.3 V (fC = 1 MHz), with RF ON 69
Supply current (read binary) ICC2 200 µA VCC = 3.3 V (fC = 1 MHz), with RF OFF 69
Supply current (update binary) ICC3 550 µA VCC = 3.3 V (fC = 1 MHz), with RF ON 69
Supply current (update binary) ICC3 500 µA VCC = 3.3 V (fC = 1 MHz), with RF OFF 69
Input low voltage (SDA, SCL); printed max is 0.3 VCC VIL -0.45 V VCC = 2.7 V (grade Y), VCC = 5.5 V 69
Input high voltage (SDA, SCL); printed min is 0.7 VCC VIH 6.5 V VCC = 2.7 V (grade Y), VCC = 5.5 V 69
Input low voltage (RF disable) VIL 0.45 V VCC = 2.7 V (grade Y), VCC = 5.5 V 69
Input high voltage (RF disable) VIH 1.4 V VCC = 2.7 V (grade Y), VCC = 5.5 V 69
Output low voltage (SDA) VOL 0.4 V IOL = 3 mA, VCC = 5.5 V 69
Output low voltage (GPO) VOL 0.4 V IOL = 1 mA, VCC = 2.7 V (grade Y) to 5.5 V 69
Write cycle endurance Ncycle 1e+06 TA ≤ 25 °C, VCC(min) < VCC < VCC(max) 77
Write cycle endurance Ncycle 600000 TA ≤ 85 °C, VCC(min) < VCC < VCC(max) 77
External RF signal frequency fC 13.553 13.56 13.567 MHz 78
Operating field according to ISO H_ISO 1500 7500 mA/m TA = 0 °C to 50 °C 78
Operating field in extended temperature range H_Extended 500 7500 mA/m TA = -40 °C to 85 °C 78
100% carrier modulation index MICARRIER 90 100 % MI=(A-B)/(A+B) 78
Minimum time from carrier generation to first data tMIN CD 5 ms From H-field min 78
RF write time (including internal Verify) for one page Wt 6 ms 78
RF OFF time tRF_OFF 5 ms Chip reset 78
Clock frequency fC 0.05 1000 kHz Test conditions specified in Table 74 71
Clock pulse width high tCHCL 260 ns Test conditions specified in Table 74 71
Clock pulse width low tCLCH 500 ns Test conditions specified in Table 74 71
SDA (out) fall time tDL1DL2 20 120 ns Test conditions specified in Table 74 71
Data in set up time tDXCX 50 ns Test conditions specified in Table 74 71
Data out hold time tCLQX 100 ns Test conditions specified in Table 74 71
Clock low to next data valid (access time) tCLQV 450 ns Test conditions specified in Table 74 71
Start condition set up time (tSU:STA) tCHDX 250 ns Test conditions specified in Table 74 71
Start condition hold time (tHD:STA) tDLCL 250 ns Test conditions specified in Table 74 71
Stop condition set up time (tSU:STO) tCHDH 250 ns Test conditions specified in Table 74 71
Time between Stop condition and next Start condition (tBUF) tDHDL 500 ns Test conditions specified in Table 74 71
I2C write time in one page tW 5 ms Test conditions specified in Table 74 71
I2C write time up to 246 bytes tW 150 ms Test conditions specified in Table 74 71
Delay for I2C token release tSTART_OUT 20 40 ms 70

CAD (KiCad official)

  • Symbol: M24SR04-YDW6T
  • Footprint: Package_SO:TSSOP-8_4.4x3mm_P0.65mm
  • 3D model: TSSOP-8 (KiCad packages3D, STEP)
  • 3D model files: m24sr04-ydw6t-etched.step / m24sr04-ydw6t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); m24sr04-ydw6t.step / m24sr04-ydw6t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (89 pp, sha256 d434a54171393933, retrieved 2026-11-12, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF