main
Ray
Publish 0.1.0
177510a
M24M01-DFDW6TP
STMicroelectronics · EEPROM · TSSOP-8
M24M01-DFDW6TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DU | unconnected | Don't use: no signal should be applied on this pin, and if connected it must be connected to VSS. |
| 2 | E1 | input | Chip Enable input that sets device select code bit b2 and must be tied to VCC or VSS, reading as low when left floating. |
| 3 | E2 | input | Chip Enable input that sets device select code bit b3 and must be tied to VCC or VSS, reading as low when left floating. |
| 4 | VSS | power_in | Ground, the reference for the VCC supply voltage. |
| 5 | SDA | bidirectional | Serial data input/output with an open-drain output that needs an external pull-up resistor. |
| 6 | SCL | input | Serial clock input that strobes data on SDA in and out. |
| 7 | WC | input | Write Control input that disables writes to the whole memory array when driven high and enables them when driven low or left floating. |
| 8 | VCC | power_in | Supply voltage of 1.7 V to 5.5 V for the M24M01-DF, to be decoupled with about 10 nF to 100 nF close to the VCC/VSS pins. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 1.7 | 5.5 | V | Voltage range F | 24 | |
| Ambient operating temperature | TA | -40 | 85 | °C | Voltage range F | 24 | |
| Operating clock frequency | fC | 1 | MHz | Voltage range F | 24 | ||
| Ambient operating temperature (absolute max) | -40 | 130 | °C | 23 | |||
| Storage temperature | TSTG | -65 | 150 | °C | 23 | ||
| DC output current | IOL | 5 | mA | SDA = 0 | 23 | ||
| Input or output range | VIO | -0.5 | 6.5 | V | 23 | ||
| Supply voltage | VCC | -0.5 | 6.5 | V | 23 | ||
| Electrostatic pulse (Human Body model) | VESD | 4000 | V | AEC-Q100-002, C1=100 pF, R1=1500 Ω | 23 | ||
| Input capacitance (SDA) | CIN | 8 | pF | Sampled only | 24 | ||
| Input capacitance (other pins) | CIN | 6 | pF | Sampled only | 24 | ||
| Input impedance (WC) low | ZL | 30 | kΩ | VIN < 0.3 VCC | 24 | ||
| Input impedance (WC) high | ZH | 400 | kΩ | VIN > 0.7 VCC | 24 | ||
| Input leakage current (E1, E2, SCL, SDA) | ILI | -2 | 2 | µA | VIN = VSS or VCC, device in Standby mode | 27 | |
| Output leakage current | ILO | -2 | 2 | µA | SDA in Hi-Z, external voltage applied on SDA: VSS or VCC | 27 | |
| Supply current (Read) | ICC | 1 | mA | VCC = 1.7 V, fc = 400 kHz | 27 | ||
| Supply current (Read) | ICC | 1.5 | mA | VCC = 5.5 V, fc = 400 kHz | 27 | ||
| Supply current (Write) | ICC0 | 2 | mA | During tW; characterized only | 27 | ||
| Standby supply current | ICC1 | 3 | µA | Device not selected, VIN = VSS or VCC, VCC = 1.7 V | 27 | ||
| Standby supply current | ICC1 | 5 | µA | Device not selected, VIN = VSS or VCC, VCC = 5.5 V | 27 | ||
| Input low voltage (lower limit) | VIL | -0.45 | V | 1.7 V ≤ VCC < 2.5 V | 27 | ||
| Input low voltage (upper limit, multiple of VCC) | VIL | 0.25 | VCC | 1.7 V ≤ VCC < 2.5 V | 27 | ||
| Input low voltage (upper limit, multiple of VCC) | VIL | 0.3 | VCC | 2.5 V ≤ VCC < 5.5 V | 27 | ||
| Input high voltage (lower limit, multiple of VCC) | VIH | 0.75 | VCC | 1.7 V ≤ VCC < 2.5 V; max printed as VCC+1 | 27 | ||
| Input high voltage (lower limit, multiple of VCC) | VIH | 0.7 | VCC | 2.5 V ≤ VCC < 5.5 V; max printed as VCC+1 | 27 | ||
| Output low voltage | VOL | 0.2 | V | IOL = 1.0 mA, VCC = 1.7 V | 27 | ||
| Output low voltage | VOL | 0.4 | V | IOL = 2.1 mA, VCC = 2.5 V | 27 | ||
| Data retention | 200 | Year | TA = 55 °C | 25 | |||
| Clock frequency (400 kHz) | fC | 400 | kHz | 400 kHz AC characteristics | 28 | ||
| Clock pulse width high | tCHCL | 600 | ns | 400 kHz | 28 | ||
| Clock pulse width low | tCLCH | 1300 | ns | 400 kHz | 28 | ||
| SDA (out) fall time | tQL1QL2 | 20 | 300 | ns | 400 kHz; min with CL = 10 pF; characterized only | 28 | |
| Data in set up time | tDXCH | 100 | ns | 400 kHz | 28 | ||
| Data in hold time | tCLDX | 0 | ns | 400 kHz | 28 | ||
| Data out hold time | tCLQX | 100 | ns | 400 kHz | 28 | ||
| Clock low to next data valid (access time) | tCLQV | 900 | ns | 400 kHz | 28 | ||
| Start condition setup time | tCHDL | 600 | ns | 400 kHz | 28 | ||
| Start condition hold time | tDLCL | 600 | ns | 400 kHz | 28 | ||
| Stop condition set up time | tCHDH | 600 | ns | 400 kHz | 28 | ||
| Time between Stop condition and next Start condition | tDHDL | 1300 | ns | 400 kHz | 28 | ||
| WC set up time (before the Start condition) | tWLDL | 0 | µs | 400 kHz; characterized only | 28 | ||
| WC hold time (after the Stop condition) | tDHWH | 1 | µs | 400 kHz; characterized only | 28 | ||
| Internal Write cycle duration | tW | 5 | ms | 400 kHz | 28 | ||
| Pulse width ignored (input filter on SCL and SDA) | tNS | 50 | ns | single glitch; characterized only | 28 | ||
| Clock frequency (1 MHz) | fC | 0 | 1 | MHz | 1 MHz AC characteristics | 29 | |
| Clock pulse width high | tCHCL | 300 | ns | 1 MHz | 29 | ||
| Clock pulse width low | tCLCH | 400 | ns | 1 MHz | 29 | ||
| SDA (out) fall time | tQL1QL2 | 120 | ns | 1 MHz | 29 | ||
| Data in setup time | tDXCX | 80 | ns | 1 MHz | 29 | ||
| Data out hold time | tCLQX | 50 | ns | 1 MHz | 29 | ||
| Clock low to next data valid (access time) | tCLQV | 500 | ns | 1 MHz | 29 | ||
| Start condition setup time | tCHDL | 250 | ns | 1 MHz | 29 | ||
| Start condition hold time | tDLCL | 250 | ns | 1 MHz | 29 | ||
| Stop condition setup time | tCHDH | 250 | ns | 1 MHz | 29 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST ECOPACK® | 23 |
CAD (KiCad official)
- Symbol:
M24M01-DFDW6TP - Footprint:
Package_SO:TSSOP-8_3x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
m24m01-dfdw6tp-etched.step/m24m01-dfdw6tp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m24m01-dfdw6tp.step/m24m01-dfdw6tp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (47 pp, sha256
2fcf2a055ea9b4cc, retrieved 2026-10-23, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# M24M01-DFDW6TP
**STMicroelectronics** · EEPROM · TSSOP-8
M24M01-DFDW6TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DU | unconnected | Don't use: no signal should be applied on this pin, and if connected it must be connected to VSS. |
| 2 | E1 | input | Chip Enable input that sets device select code bit b2 and must be tied to VCC or VSS, reading as low when left floating. |
| 3 | E2 | input | Chip Enable input that sets device select code bit b3 and must be tied to VCC or VSS, reading as low when left floating. |
| 4 | VSS | power_in | Ground, the reference for the VCC supply voltage. |
| 5 | SDA | bidirectional | Serial data input/output with an open-drain output that needs an external pull-up resistor. |
| 6 | SCL | input | Serial clock input that strobes data on SDA in and out. |
| 7 | WC | input | Write Control input that disables writes to the whole memory array when driven high and enables them when driven low or left floating. |
| 8 | VCC | power_in | Supply voltage of 1.7 V to 5.5 V for the M24M01-DF, to be decoupled with about 10 nF to 100 nF close to the VCC/VSS pins. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 1.7 | | 5.5 | V | Voltage range F | 24 |
| Ambient operating temperature | TA | -40 | | 85 | °C | Voltage range F | 24 |
| Operating clock frequency | fC | | | 1 | MHz | Voltage range F | 24 |
| Ambient operating temperature (absolute max) | | -40 | | 130 | °C | | 23 |
| Storage temperature | TSTG | -65 | | 150 | °C | | 23 |
| DC output current | IOL | | | 5 | mA | SDA = 0 | 23 |
| Input or output range | VIO | -0.5 | | 6.5 | V | | 23 |
| Supply voltage | VCC | -0.5 | | 6.5 | V | | 23 |
| Electrostatic pulse (Human Body model) | VESD | | | 4000 | V | AEC-Q100-002, C1=100 pF, R1=1500 Ω | 23 |
| Input capacitance (SDA) | CIN | | | 8 | pF | Sampled only | 24 |
| Input capacitance (other pins) | CIN | | | 6 | pF | Sampled only | 24 |
| Input impedance (WC) low | ZL | 30 | | | kΩ | VIN < 0.3 VCC | 24 |
| Input impedance (WC) high | ZH | 400 | | | kΩ | VIN > 0.7 VCC | 24 |
| Input leakage current (E1, E2, SCL, SDA) | ILI | -2 | | 2 | µA | VIN = VSS or VCC, device in Standby mode | 27 |
| Output leakage current | ILO | -2 | | 2 | µA | SDA in Hi-Z, external voltage applied on SDA: VSS or VCC | 27 |
| Supply current (Read) | ICC | | | 1 | mA | VCC = 1.7 V, fc = 400 kHz | 27 |
| Supply current (Read) | ICC | | | 1.5 | mA | VCC = 5.5 V, fc = 400 kHz | 27 |
| Supply current (Write) | ICC0 | | | 2 | mA | During tW; characterized only | 27 |
| Standby supply current | ICC1 | | | 3 | µA | Device not selected, VIN = VSS or VCC, VCC = 1.7 V | 27 |
| Standby supply current | ICC1 | | | 5 | µA | Device not selected, VIN = VSS or VCC, VCC = 5.5 V | 27 |
| Input low voltage (lower limit) | VIL | -0.45 | | | V | 1.7 V ≤ VCC < 2.5 V | 27 |
| Input low voltage (upper limit, multiple of VCC) | VIL | | | 0.25 | VCC | 1.7 V ≤ VCC < 2.5 V | 27 |
| Input low voltage (upper limit, multiple of VCC) | VIL | | | 0.3 | VCC | 2.5 V ≤ VCC < 5.5 V | 27 |
| Input high voltage (lower limit, multiple of VCC) | VIH | 0.75 | | | VCC | 1.7 V ≤ VCC < 2.5 V; max printed as VCC+1 | 27 |
| Input high voltage (lower limit, multiple of VCC) | VIH | 0.7 | | | VCC | 2.5 V ≤ VCC < 5.5 V; max printed as VCC+1 | 27 |
| Output low voltage | VOL | | | 0.2 | V | IOL = 1.0 mA, VCC = 1.7 V | 27 |
| Output low voltage | VOL | | | 0.4 | V | IOL = 2.1 mA, VCC = 2.5 V | 27 |
| Data retention | | 200 | | | Year | TA = 55 °C | 25 |
| Clock frequency (400 kHz) | fC | | | 400 | kHz | 400 kHz AC characteristics | 28 |
| Clock pulse width high | tCHCL | 600 | | | ns | 400 kHz | 28 |
| Clock pulse width low | tCLCH | 1300 | | | ns | 400 kHz | 28 |
| SDA (out) fall time | tQL1QL2 | 20 | | 300 | ns | 400 kHz; min with CL = 10 pF; characterized only | 28 |
| Data in set up time | tDXCH | 100 | | | ns | 400 kHz | 28 |
| Data in hold time | tCLDX | 0 | | | ns | 400 kHz | 28 |
| Data out hold time | tCLQX | 100 | | | ns | 400 kHz | 28 |
| Clock low to next data valid (access time) | tCLQV | | | 900 | ns | 400 kHz | 28 |
| Start condition setup time | tCHDL | 600 | | | ns | 400 kHz | 28 |
| Start condition hold time | tDLCL | 600 | | | ns | 400 kHz | 28 |
| Stop condition set up time | tCHDH | 600 | | | ns | 400 kHz | 28 |
| Time between Stop condition and next Start condition | tDHDL | 1300 | | | ns | 400 kHz | 28 |
| WC set up time (before the Start condition) | tWLDL | 0 | | | µs | 400 kHz; characterized only | 28 |
| WC hold time (after the Stop condition) | tDHWH | 1 | | | µs | 400 kHz; characterized only | 28 |
| Internal Write cycle duration | tW | | | 5 | ms | 400 kHz | 28 |
| Pulse width ignored (input filter on SCL and SDA) | tNS | | | 50 | ns | single glitch; characterized only | 28 |
| Clock frequency (1 MHz) | fC | 0 | | 1 | MHz | 1 MHz AC characteristics | 29 |
| Clock pulse width high | tCHCL | 300 | | | ns | 1 MHz | 29 |
| Clock pulse width low | tCLCH | 400 | | | ns | 1 MHz | 29 |
| SDA (out) fall time | tQL1QL2 | | | 120 | ns | 1 MHz | 29 |
| Data in setup time | tDXCX | 80 | | | ns | 1 MHz | 29 |
| Data out hold time | tCLQX | 50 | | | ns | 1 MHz | 29 |
| Clock low to next data valid (access time) | tCLQV | | | 500 | ns | 1 MHz | 29 |
| Start condition setup time | tCHDL | 250 | | | ns | 1 MHz | 29 |
| Start condition hold time | tDLCL | 250 | | | ns | 1 MHz | 29 |
| Stop condition setup time | tCHDH | 250 | | | ns | 1 MHz | 29 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST ECOPACK® | 23 |
## CAD (KiCad official)
- Symbol: `M24M01-DFDW6TP`
- Footprint: `Package_SO:TSSOP-8_3x3mm_P0.65mm`
- 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files: `m24m01-dfdw6tp-etched.step` / `m24m01-dfdw6tp-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `m24m01-dfdw6tp.step` / `m24m01-dfdw6tp.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/resource/en/datasheet/m24m01-dfdw6tp.pdf) (47 pp, sha256 `2fcf2a055ea9b4cc`, retrieved 2026-10-23, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text+vision), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/m24m01-dfdw6tp-datasheet.pdf)