Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

M24C64-DRMN3TP

STMicroelectronics · EEPROM · SO-8

M24C64-DRMN3TP from STMicroelectronics, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 E0 input Chip Enable input that sets bit b1 of the 7-bit device select code and must be tied to VCC or VSS, and reads as low (0) if left floating.
2 E1 input Chip Enable input that sets bit b2 of the 7-bit device select code and must be tied to VCC or VSS, and reads as low (0) if left floating.
3 E2 input Chip Enable input that sets bit b3 of the 7-bit device select code and must be tied to VCC or VSS, and reads as low (0) if left floating.
4 VSS power_in Ground, the reference for the VCC supply voltage.
5 SDA bidirectional Serial Data input/output with an open-drain output that can be wire-OR'ed on the bus, and it needs a pull-up resistor to VCC.
6 SCL input Serial Clock input that strobes the data on SDA in and out.
7 WC input Write Control input (active high) that disables write operations to the entire memory array when driven high, and writes are enabled when it is driven low or left floating.
8 VCC power_in Supply voltage pin, specified from 1.7 V to 5.5 V, with a 10 nF to 100 nF decoupling capacitor recommended close to the VCC/VSS pins.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package SO-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage VCC 1.7 5.5 V Voltage range R 26
Ambient operating temperature TA -40 125 °C 26
Ambient operating temperature (abs max) -40 130 °C 25
Storage temperature TSTG -65 150 °C 25
Input or output range VIO -0.5 6.5 V 25
DC output current IOL 5 mA SDA = 0 25
Supply voltage (abs max) VCC -0.5 6.5 V 25
Electrostatic pulse (HBM) VESD 4000 V Human Body model 25
Write cycle endurance Ncycle 4e+06 cycles TA ≤ 25 °C, 1.7 V < VCC < 5.5 V 26
Write cycle endurance Ncycle 1.2e+06 cycles TA = 85 °C, 1.7 V < VCC < 5.5 V 26
Write cycle endurance Ncycle 600000 cycles TA = 125 °C, 1.7 V < VCC < 5.5 V 26
Input capacitance (SDA) CIN 8 pF 27
Input capacitance (other pins) CIN 6 pF 27
Input impedance (E2, E1, E0, WC) ZL 30 kΩ VIN < 0.3 VCC 27
Input impedance (E2, E1, E0, WC) ZH 500 kΩ VIN > 0.7 VCC 27
Input leakage current (SCL, SDA, E2, E1, E0) ILI -2 2 µA VIN = VSS or VCC, device in Standby mode 28
Output leakage current ILO -2 2 µA SDA in Hi-Z, external voltage applied on SDA: VSS or VCC 28
Supply current (Read) ICC 2 mA fC = 400 kHz, VCC = 5.5 V 28
Supply current (Read) ICC 1 mA fC = 400 kHz, VCC = 1.7 V 28
Supply current (Write) ICC0 2 mA During tW 28
Standby supply current ICC1 1 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 1.7 V 28
Standby supply current ICC1 2 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 2.5 V 28
Standby supply current ICC1 3 µA Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 5.5 V 28
Standby supply current ICC1 15 µA Device not selected, t° = 125 °C, VIN = VSS or VCC, VCC = 1.7 V 28
Standby supply current ICC1 20 µA Device not selected, t° = 125 °C, VIN = VSS or VCC, VCC = 5.5 V 28
Input low voltage (SCL, SDA, WC) VIL -0.45 V max is 0.3 VCC (VCC-relative, not numeric) 28
Input high voltage (SCL, SDA) VIH 6.5 V min is 0.7 VCC (VCC-relative, not numeric) 28
Output low voltage VOL 0.4 V IOL = 2.1 mA, VCC = 2.5 V or IOL = 3 mA, VCC = 5.5 V 28
Output low voltage VOL 0.3 V IOL = 1 mA, VCC = 1.7 V 28
Internal reset threshold voltage VRES 0.5 1.5 V Characterized only, not 100% tested 28
Clock frequency (1 MHz) fC 0 1 MHz 30
Clock pulse width high (1 MHz) tCHCL 260 ns 30
Clock pulse width low (1 MHz) tCLCH 400 ns 30
SDA (out) fall time (1 MHz) tQL1QL2 120 ns Characterized only, not tested in production 30
Data in setup time (1 MHz) tDXCX 50 ns 30
Data in hold time (1 MHz) tCLDX 0 ns 30
Data out hold time (1 MHz) tCLQX 100 ns 30
Clock low to next data valid (1 MHz) tCLQV 450 ns 30
Start condition setup time (1 MHz) tCHDL 250 ns 30
Start condition hold time (1 MHz) tDLCL 250 ns 30
Stop condition setup time (1 MHz) tCHDH 250 ns 30
Time between Stop and next Start (1 MHz) tDHDL 500 ns 30
WC set up time (1 MHz) tWLDL 0 µs 30
WC hold time (1 MHz) tDHWH 1 µs 30
Write time (1 MHz) tW 4 ms 30
Pulse width ignored (input filter) tNS 80 ns 1 MHz table 30
Clock frequency (400 kHz) fC 400 kHz 29
Clock pulse width high (400 kHz) tCHCL 600 ns 29
Clock pulse width low (400 kHz) tCLCH 1300 ns 29
Clock low to next data valid (400 kHz) tCLQV 900 ns 29
Data in set up time (400 kHz) tDXCX 100 ns 29
Start condition setup time (400 kHz) tCHDL 600 ns 29
Start condition hold time (400 kHz) tDLCL 600 ns 29
Time between Stop and next Start (400 kHz) tDHDL 1300 ns 29
Write time (400 kHz) tW 4 ms 29

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Standard J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST 25

CAD (KiCad official)

  • Symbol: M24C64-DRMN3TP
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SO-8 (KiCad packages3D, STEP)
  • 3D model files: m24c64-drmn3tp-etched.step / m24c64-drmn3tp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); m24c64-drmn3tp.step / m24c64-drmn3tp.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (41 pp, sha256 85c68012834e5400, retrieved 2026-10-23, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text+vision), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF