main
Ray
Publish 0.1.0
49c5643
M24C08-DRDW3TP
STMicroelectronics · EEPROM · TSSOP-8
M24C08-DRDW3TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect pin; the datasheet's 8-pin package connections figure shows it as NC and gives no function. |
| 2 | NC | unconnected | No connect pin; the datasheet's 8-pin package connections figure shows it as NC and gives no function. |
| 3 | E2 | input | Chip Enable input that sets the value looked for on bit b3 of the device select code; tie it to VCC or VSS, and it reads as low (0) if left floating. |
| 4 | VSS | power_in | Ground, the reference for the VCC supply voltage. |
| 5 | SDA | bidirectional | Serial data input/output with an open-drain output that can be wire-OR'ed on the bus; it needs a pull-up resistor to VCC. |
| 6 | SCL | input | Serial clock input that strobes data on SDA in and out. |
| 7 | WC | input | Write Control input that disables writes to the entire memory array when driven high, and enables them when driven low or left floating. |
| 8 | VCC | power_in | Supply voltage pin, operating range 1.7 V to 5.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 1.7 | 5.5 | V | 25 | ||
| Ambient operating temperature | TA | -40 | 125 | °C | 25 | ||
| Ambient operating temperature | -40 | 130 | °C | 24 | |||
| Storage temperature | TSTG | -65 | 150 | °C | 24 | ||
| Input or output range | VIO | -0.5 | 6.5 | V | 24 | ||
| DC output current | IOL | 5 | mA | SDA = 0 | 24 | ||
| Supply voltage | VCC | -0.5 | 6.5 | V | 24 | ||
| Electrostatic pulse (Human Body model) | VESD | 4000 | V | AEC-Q100-002 | 24 | ||
| Input capacitance (SDA) | CIN | 8 | pF | 26 | |||
| Input capacitance (other pins) | CIN | 6 | pF | 26 | |||
| Input impedance (WC) | ZL | 30 | kΩ | VIN < 0.3 VCC | 26 | ||
| Input impedance (WC) | ZH | 500 | kΩ | VIN > 0.7 VCC | 26 | ||
| Write cycle endurance | Ncycle | 4e+06 | TA ≤ 25 °C, 1.7 V < VCC < 5.5 V | 26 | |||
| Write cycle endurance | Ncycle | 1.2e+06 | TA = 85 °C, 1.7 V < VCC < 5.5 V | 26 | |||
| Write cycle endurance | Ncycle | 600000 | TA = 125 °C, 1.7 V < VCC < 5.5 V | 26 | |||
| Input leakage current (SCL, SDA, Ei) | ILI | -2 | 2 | µA | VIN = VSS or VCC, device in Standby mode | 27 | |
| Output leakage current | ILO | -2 | 2 | µA | SDA in Hi-Z, external voltage applied on SDA: VSS or VCC | 27 | |
| Supply current (Read) | ICC | 2 | mA | fC = 400 kHz, VCC = 5.5 V | 27 | ||
| Supply current (Read) | ICC | 1 | mA | fC = 400 kHz, VCC = 1.7 V | 27 | ||
| Supply current (Write) | ICC0 | 2 | mA | During tW | 27 | ||
| Standby supply current | ICC1 | 1 | µA | Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 1.7 V | 27 | ||
| Standby supply current | ICC1 | 3 | µA | Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 5.5 V | 27 | ||
| Standby supply current | ICC1 | 15 | µA | Device not selected, t° = 125 °C, VIN = VSS or VCC, VCC = 1.7 V | 27 | ||
| Standby supply current | ICC1 | 20 | µA | Device not selected, t° = 125 °C, VIN = VSS or VCC, VCC = 5.5 V | 27 | ||
| Input low voltage (SCL, SDA, WC, Ei) | VIL | -0.45 | 0.3 | V | 27 | ||
| Input high voltage (SCL, SDA) | VIH | 0.7 | 6.5 | V | 27 | ||
| Input high voltage (WC, Ei) | VIH | 0.7 | V | Ei inputs tied to VCC | 27 | ||
| Output low voltage | VOL | 0.4 | V | IOL = 2.1 mA, VCC = 2.5 V or IOL = 3 mA, VCC = 5.5 V | 27 | ||
| Output low voltage | VOL | 0.3 | V | IOL = 1 mA, VCC = 1.7 V | 27 | ||
| Internal reset threshold voltage | VRES | 0.5 | 1.5 | V | 27 | ||
| Clock frequency (400 kHz) | fC | 400 | kHz | 28 | |||
| Clock pulse width high | tCHCL | 600 | ns | 28 | |||
| Clock pulse width low | tCLCH | 1300 | ns | 28 | |||
| SDA (out) fall time | tQL1QL2 | 20 | 120 | ns | CL = 10 pF | 28 | |
| Data in setup time | tDXCH | 100 | ns | 28 | |||
| Data out hold time | tDH | 100 | ns | 28 | |||
| Clock low to next data valid (access time) | tAA | 900 | ns | 28 | |||
| Start condition setup time | tCHDL | 600 | ns | 28 | |||
| Start condition hold time | tDLCL | 600 | ns | 28 | |||
| Stop condition set up time | tCHDH | 600 | ns | 28 | |||
| Time between Stop condition and next Start condition | tDHDL | 1300 | ns | 28 | |||
| WC hold time (after the Stop condition) | tDHWH | 1 | µs | WC=0 hold time condition to enable the execution of a WRITE command | 28 | ||
| Write time | tW | 4 | ms | 28 | |||
| Pulse width ignored (input filter on SCL and SDA) | tNS | 80 | ns | single glitch | 28 | ||
| Clock frequency (1 MHz) | fC | 0 | 1 | MHz | 29 | ||
| Clock pulse width high | tCHCL | 260 | ns | 29 | |||
| Clock pulse width low | tCLCH | 500 | ns | 29 | |||
| SDA (out) fall time | tQL1QL2 | 20 | 120 | ns | 29 | ||
| Data in setup time | tDXCH | 50 | ns | 29 | |||
| Data out hold time | tDH | 100 | ns | 29 | |||
| Clock low to next data valid (access time) | tAA | 450 | ns | 29 | |||
| Start condition setup time | tCHDL | 250 | ns | 29 | |||
| Start condition hold time | tDLCL | 250 | ns | 29 | |||
| Stop condition setup time | tCHDH | 250 | ns | 29 | |||
| Time between Stop condition and next Start condition | tDHDL | 500 | ns | 29 | |||
| WC hold time (after the Stop condition) | tDHWH | 1 | µs | WC=0 hold time condition to enable the execution of a WRITE command | 29 | ||
| Write time | tW | 4 | ms | 29 | |||
| Pulse width ignored (input filter on SCL and SDA) | tNS | 80 | ns | single glitch | 29 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST ECOPACK® | 24 |
CAD (KiCad official)
- Symbol:
M24C08-DRDW3TP - Footprint:
Package_SO:TSSOP-8_4.4x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
m24c08-drdw3tp-k-etched.step/m24c08-drdw3tp-k-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m24c08-drdw3tp-k.step/m24c08-drdw3tp-k.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (40 pp, sha256
03cd643d0d3bb938, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# M24C08-DRDW3TP
**STMicroelectronics** · EEPROM · TSSOP-8
M24C08-DRDW3TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect pin; the datasheet's 8-pin package connections figure shows it as NC and gives no function. |
| 2 | NC | unconnected | No connect pin; the datasheet's 8-pin package connections figure shows it as NC and gives no function. |
| 3 | E2 | input | Chip Enable input that sets the value looked for on bit b3 of the device select code; tie it to VCC or VSS, and it reads as low (0) if left floating. |
| 4 | VSS | power_in | Ground, the reference for the VCC supply voltage. |
| 5 | SDA | bidirectional | Serial data input/output with an open-drain output that can be wire-OR'ed on the bus; it needs a pull-up resistor to VCC. |
| 6 | SCL | input | Serial clock input that strobes data on SDA in and out. |
| 7 | WC | input | Write Control input that disables writes to the entire memory array when driven high, and enables them when driven low or left floating. |
| 8 | VCC | power_in | Supply voltage pin, operating range 1.7 V to 5.5 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 1.7 | | 5.5 | V | | 25 |
| Ambient operating temperature | TA | -40 | | 125 | °C | | 25 |
| Ambient operating temperature | | -40 | | 130 | °C | | 24 |
| Storage temperature | TSTG | -65 | | 150 | °C | | 24 |
| Input or output range | VIO | -0.5 | | 6.5 | V | | 24 |
| DC output current | IOL | | | 5 | mA | SDA = 0 | 24 |
| Supply voltage | VCC | -0.5 | | 6.5 | V | | 24 |
| Electrostatic pulse (Human Body model) | VESD | | | 4000 | V | AEC-Q100-002 | 24 |
| Input capacitance (SDA) | CIN | | | 8 | pF | | 26 |
| Input capacitance (other pins) | CIN | | | 6 | pF | | 26 |
| Input impedance (WC) | ZL | 30 | | | kΩ | VIN < 0.3 VCC | 26 |
| Input impedance (WC) | ZH | 500 | | | kΩ | VIN > 0.7 VCC | 26 |
| Write cycle endurance | Ncycle | | | 4e+06 | | TA ≤ 25 °C, 1.7 V < VCC < 5.5 V | 26 |
| Write cycle endurance | Ncycle | | | 1.2e+06 | | TA = 85 °C, 1.7 V < VCC < 5.5 V | 26 |
| Write cycle endurance | Ncycle | | | 600000 | | TA = 125 °C, 1.7 V < VCC < 5.5 V | 26 |
| Input leakage current (SCL, SDA, Ei) | ILI | -2 | | 2 | µA | VIN = VSS or VCC, device in Standby mode | 27 |
| Output leakage current | ILO | -2 | | 2 | µA | SDA in Hi-Z, external voltage applied on SDA: VSS or VCC | 27 |
| Supply current (Read) | ICC | | | 2 | mA | fC = 400 kHz, VCC = 5.5 V | 27 |
| Supply current (Read) | ICC | | | 1 | mA | fC = 400 kHz, VCC = 1.7 V | 27 |
| Supply current (Write) | ICC0 | | | 2 | mA | During tW | 27 |
| Standby supply current | ICC1 | | | 1 | µA | Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 1.7 V | 27 |
| Standby supply current | ICC1 | | | 3 | µA | Device not selected, t° = 85 °C, VIN = VSS or VCC, VCC = 5.5 V | 27 |
| Standby supply current | ICC1 | | | 15 | µA | Device not selected, t° = 125 °C, VIN = VSS or VCC, VCC = 1.7 V | 27 |
| Standby supply current | ICC1 | | | 20 | µA | Device not selected, t° = 125 °C, VIN = VSS or VCC, VCC = 5.5 V | 27 |
| Input low voltage (SCL, SDA, WC, Ei) | VIL | -0.45 | | 0.3 | V | | 27 |
| Input high voltage (SCL, SDA) | VIH | 0.7 | | 6.5 | V | | 27 |
| Input high voltage (WC, Ei) | VIH | 0.7 | | | V | Ei inputs tied to VCC | 27 |
| Output low voltage | VOL | | | 0.4 | V | IOL = 2.1 mA, VCC = 2.5 V or IOL = 3 mA, VCC = 5.5 V | 27 |
| Output low voltage | VOL | | | 0.3 | V | IOL = 1 mA, VCC = 1.7 V | 27 |
| Internal reset threshold voltage | VRES | 0.5 | | 1.5 | V | | 27 |
| Clock frequency (400 kHz) | fC | | | 400 | kHz | | 28 |
| Clock pulse width high | tCHCL | 600 | | | ns | | 28 |
| Clock pulse width low | tCLCH | 1300 | | | ns | | 28 |
| SDA (out) fall time | tQL1QL2 | 20 | | 120 | ns | CL = 10 pF | 28 |
| Data in setup time | tDXCH | 100 | | | ns | | 28 |
| Data out hold time | tDH | 100 | | | ns | | 28 |
| Clock low to next data valid (access time) | tAA | | | 900 | ns | | 28 |
| Start condition setup time | tCHDL | 600 | | | ns | | 28 |
| Start condition hold time | tDLCL | 600 | | | ns | | 28 |
| Stop condition set up time | tCHDH | 600 | | | ns | | 28 |
| Time between Stop condition and next Start condition | tDHDL | 1300 | | | ns | | 28 |
| WC hold time (after the Stop condition) | tDHWH | 1 | | | µs | WC=0 hold time condition to enable the execution of a WRITE command | 28 |
| Write time | tW | | | 4 | ms | | 28 |
| Pulse width ignored (input filter on SCL and SDA) | tNS | | | 80 | ns | single glitch | 28 |
| Clock frequency (1 MHz) | fC | 0 | | 1 | MHz | | 29 |
| Clock pulse width high | tCHCL | 260 | | | ns | | 29 |
| Clock pulse width low | tCLCH | 500 | | | ns | | 29 |
| SDA (out) fall time | tQL1QL2 | 20 | | 120 | ns | | 29 |
| Data in setup time | tDXCH | 50 | | | ns | | 29 |
| Data out hold time | tDH | 100 | | | ns | | 29 |
| Clock low to next data valid (access time) | tAA | | | 450 | ns | | 29 |
| Start condition setup time | tCHDL | 250 | | | ns | | 29 |
| Start condition hold time | tDLCL | 250 | | | ns | | 29 |
| Stop condition setup time | tCHDH | 250 | | | ns | | 29 |
| Time between Stop condition and next Start condition | tDHDL | 500 | | | ns | | 29 |
| WC hold time (after the Stop condition) | tDHWH | 1 | | | µs | WC=0 hold time condition to enable the execution of a WRITE command | 29 |
| Write time | tW | | | 4 | ms | | 29 |
| Pulse width ignored (input filter on SCL and SDA) | tNS | | | 80 | ns | single glitch | 29 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | TLEAD Lead temperature during soldering see note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST ECOPACK® | 24 |
## CAD (KiCad official)
- Symbol: `M24C08-DRDW3TP`
- Footprint: `Package_SO:TSSOP-8_4.4x3mm_P0.65mm`
- 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files: `m24c08-drdw3tp-k-etched.step` / `m24c08-drdw3tp-k-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `m24c08-drdw3tp-k.step` / `m24c08-drdw3tp-k.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8602996321091395584) (40 pp, sha256 `03cd643d0d3bb938`, retrieved 2026-11-10, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text+vision), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/m24c08-drdw3tp-k-datasheet.pdf)