← Commit history
m24c02-wmn6tp: restore the component block (pinout + model declarations) from this page's own README and symbol
1 file changed
+75−1
page.json+75−1@@ -33,5 +33,79 @@ "author": { "name": "Ray", "email": "[email protected]"+ },+ "component": {+ "mpn": "M24C02-WMN6TP",+ "manufacturer": "STMicroelectronics",+ "package": "SOIC-8",+ "pin_count": 8,+ "category": "EEPROM",+ "datasheet": "https://www.st.com/resource/en/datasheet/m24c02-wmn6tp.pdf",+ "parts": {+ "symbol": "m24c02-wmn6tp.kicad_sym",+ "footprint": "m24c02-wmn6tp.kicad_mod",+ "model_3d": "m24c02-wmn6tp-etched.glb",+ "model_3d_plain": "m24c02-wmn6tp.glb",+ "model_3d_step": "m24c02-wmn6tp-etched.step",+ "model_3d_step_plain": "m24c02-wmn6tp.step",+ "lbr": "m24c02-wmn6tp.lbr"+ },+ "pins": [+ {+ "number": "1",+ "name": "E0",+ "type": "input",+ "description": "Chip Enable address input bit 0. Tied to VCC or VSS to set b1 of the 7-bit I2C device select code, allowing up to 8 devices on one bus. Read as low (0) if left floating."+ },+ {+ "number": "2",+ "name": "E1",+ "type": "input",+ "description": "Chip Enable address input bit 1. Tied to VCC or VSS to set b2 of the 7-bit I2C device select code. Read as low (0) if left floating."+ },+ {+ "number": "3",+ "name": "E2",+ "type": "input",+ "description": "Chip Enable address input bit 2. Tied to VCC or VSS to set b3 of the 7-bit I2C device select code. Read as low (0) if left floating."+ },+ {+ "number": "4",+ "name": "VSS",+ "type": "power_in",+ "description": "Ground reference for VCC supply voltage."+ },+ {+ "number": "5",+ "name": "SDA",+ "type": "bidirectional",+ "description": "I2C Serial Data. Open-drain input/output; requires an external pull-up resistor to VCC. May be wire-OR'ed with other open-drain devices on the bus."+ },+ {+ "number": "6",+ "name": "SCL",+ "type": "input",+ "description": "I2C Serial Clock input. Strobes data on SDA(in) and clocks data out on SDA(out). Supports 100 kHz and 400 kHz I2C modes."+ },+ {+ "number": "7",+ "name": "WC",+ "type": "input",+ "description": "Write Control input (active-low, shown overlined WC). When driven high, write operations to the entire memory array are inhibited (device select and address are ACKed but data bytes are not). Writes are enabled when driven low or left floating."+ },+ {+ "number": "8",+ "name": "VCC",+ "type": "power_in",+ "description": "Supply voltage. For the -W option: 2.5 V to 5.5 V. Decouple to VSS with a 10-100 nF capacitor close to the package pins."+ }+ ],+ "provenance": {+ "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ } }-}+}