main
Ray
Publish 0.1.0
71c21f4
LYT1603D-TL
POWER INTEGRATIONS · LED Drivers · SO-8
LYT1603D-TL from POWER INTEGRATIONS, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BP | power_out | BYPASS pin provides the 5.25 V supply rail, with BYPASS voltage VBP of 5.075 V min, 5.22 V typ and 5.35 V max, and a power-up reset threshold of 4.35 V min to 4.65 V max. |
| 2 | M | bidirectional | MULTIFUNCTION pin senses inductor demagnetization (ZCD) and output OVP at 120% of VOUT when the FET is off, with steady-state range 1 V to 2.4 V, and senses line OVP when the FET is on. |
| 3 | FB | input | FEEDBACK pin senses FET current through an external current sense resistor, with normal operating voltage range VFB(REF) to 0 V, where VFB(REF) is -279 mV typical. |
| 4 | D | passive | DRAIN pin connects to the high-voltage internal MOSFET, with absolute maximum DRAIN pin voltage of -0.3 V to 725 V. |
| 5 | S | power_in | SOURCE pin is the power and signal ground; all SOURCE pins are tied together and used for heat sinking. |
| 6 | S | power_in | SOURCE pin is the power and signal ground; all SOURCE pins are tied together and used for heat sinking. |
| 7 | S | power_in | SOURCE pin is the power and signal ground; all SOURCE pins are tied together and used for heat sinking. |
| 8 | S | power_in | SOURCE pin is the power and signal ground; all SOURCE pins are tied together and used for heat sinking. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | POWER INTEGRATIONS |
| Package | SO-8 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Switching Frequency | fMIN | 18 | 20 | 22 | kHz | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 7 |
| Maximum Switch ON-Time | TON(MAX) | 37.5 | 40 | 45 | µs | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 7 |
| Minimum Switch ON-Time | TON(MIN) | 1.012 | 1.1 | 1.25 | µs | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 7 |
| FEEDBACK Pin Reference Voltage | VFB(REF) | -285 | -279 | -273 | mV | TJ = 25 °C; See Note C | 7 |
| BYPASS Pin Charge Current (ICH1) | ICH1 | -10 | -4.5 | mA | VBP = 0.0 V, VDS ≥ 36 V | 7 | |
| BYPASS Pin Charge Current (ICH2) | ICH2 | -6 | -2 | mA | VBP = 5.0 V, VDS ≥ 36 V | 7 | |
| BYPASS Pin Voltage | VBP | 5.075 | 5.22 | 5.35 | V | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 7 |
| BYPASS Pin Shunt Voltage | VBP(SHUNT) | 5.2 | 5.39 | 5.55 | V | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 8 |
| BYPASS Pin Power-Up Reset Threshold Voltage | VBP(RESET) | 4.35 | 4.5 | 4.65 | V | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 8 |
| Current Limit for Auto-Restart (LYT1x03) | ILIMIT(AR) | 1.06 | 1.15 | 1.24 | A | di/dt = 446 mA/µs; TJ = 25 °C | 8 |
| Fault Minimum Switch ON-Time | TFAULT(MIN) | 250 | 400 | ns | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 8 | |
| Input Overvoltage Threshold | IIOV | 0.9 | 1 | 1.1 | mA | TJ = 25 °C | 8 |
| MULTIFUNCTIONAL Pin Auto-Restart Threshold Voltage (Output OVP) | VOOV | 2.3 | 2.4 | 2.48 | V | TJ = 25 °C | 8 |
| MULTIFUNCTIONAL Pin Undervoltage Threshold (Output Short) | VOUV | 0.91 | 0.95 | 0.99 | V | TJ = 25 °C; See Note B | 8 |
| Junction Temperature at Fold-Back | TFB | 138 | 145 | 152 | °C | See Note B | 8 |
| ON-State Resistance (LYT1x03, TJ = 25 °C) | RDS(ON) | 4.5 | 5.2 | Ω | ID = 139 mA; TJ = 25 °C | 9 | |
| ON-State Resistance (LYT1x03, TJ = 100 °C) | RDS(ON) | 6.8 | 7.8 | Ω | ID = 139 mA; TJ = 100 °C | 9 | |
| DRAIN Pin Voltage | -0.3 | 725 | V | 7 | |||
| DRAIN Pin Peak Current (LYT1x03, higher allowed value) | 2.6 | A | Allowed while DRAIN voltage is simultaneously less than 400 V | 7 | |||
| BYPASS Pin Voltage (absolute maximum) | -0.3 | 6 | V | 7 | |||
| MULTIFUNCTION, FEEDBACK Pin Voltage | -0.45 | 7 | V | 7 | |||
| Lead Temperature | 260 | °C | 7 | ||||
| Storage Temperature | -65 | 150 | °C | 7 | |||
| Operating Junction Temperature | -40 | 150 | °C | See Note 4 (normally limited by internal circuitry) | 7 | ||
| MULTIFUNCTION Pin Steady-State Operation Voltage Range | 1 | 2.4 | V | Mode 1: FET OFF | 2 | ||
| Thermal Resistance Junction-to-Ambient (0.36 sq. in. copper) | θJA | 100 | °C/W | Soldered to 0.36 sq. inch (232 mm2) 2 oz. copper clad, no external heat sink | 7 | ||
| Thermal Resistance Junction-to-Ambient (1 sq. in. copper) | θJA | 80 | °C/W | Soldered to 1 sq. in. (645 mm2) 2 oz. copper clad | 7 | ||
| Thermal Resistance Junction-to-Case (SOURCE pin) | θJC | 30 | °C/W | Measured on the SOURCE pin close to plastic interface | 7 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | ground potential SOURCE pins are used for heat sinking. This allows the designer to maximize the copper area for good thermal management but, without having the risk of increased EMI. | 5 |
CAD (KiCad official)
- Symbol:
LYT1603D-TL - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files:
lyt1603d-tl-etched.step/lyt1603d-tl-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lyt1603d-tl.step/lyt1603d-tl.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: POWER INTEGRATIONS datasheet (14 pp, sha256
c25fe052456356af, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LYT1603D-TL
**POWER INTEGRATIONS** · LED Drivers · SO-8
LYT1603D-TL from POWER INTEGRATIONS, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BP | power_out | BYPASS pin provides the 5.25 V supply rail, with BYPASS voltage VBP of 5.075 V min, 5.22 V typ and 5.35 V max, and a power-up reset threshold of 4.35 V min to 4.65 V max. |
| 2 | M | bidirectional | MULTIFUNCTION pin senses inductor demagnetization (ZCD) and output OVP at 120% of VOUT when the FET is off, with steady-state range 1 V to 2.4 V, and senses line OVP when the FET is on. |
| 3 | FB | input | FEEDBACK pin senses FET current through an external current sense resistor, with normal operating voltage range VFB(REF) to 0 V, where VFB(REF) is -279 mV typical. |
| 4 | D | passive | DRAIN pin connects to the high-voltage internal MOSFET, with absolute maximum DRAIN pin voltage of -0.3 V to 725 V. |
| 5 | S | power_in | SOURCE pin is the power and signal ground; all SOURCE pins are tied together and used for heat sinking. |
| 6 | S | power_in | SOURCE pin is the power and signal ground; all SOURCE pins are tied together and used for heat sinking. |
| 7 | S | power_in | SOURCE pin is the power and signal ground; all SOURCE pins are tied together and used for heat sinking. |
| 8 | S | power_in | SOURCE pin is the power and signal ground; all SOURCE pins are tied together and used for heat sinking. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | POWER INTEGRATIONS |
| Package | SO-8 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Switching Frequency | fMIN | 18 | 20 | 22 | kHz | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 7 |
| Maximum Switch ON-Time | TON(MAX) | 37.5 | 40 | 45 | µs | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 7 |
| Minimum Switch ON-Time | TON(MIN) | 1.012 | 1.1 | 1.25 | µs | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 7 |
| FEEDBACK Pin Reference Voltage | VFB(REF) | -285 | -279 | -273 | mV | TJ = 25 °C; See Note C | 7 |
| BYPASS Pin Charge Current (ICH1) | ICH1 | -10 | | -4.5 | mA | VBP = 0.0 V, VDS ≥ 36 V | 7 |
| BYPASS Pin Charge Current (ICH2) | ICH2 | -6 | | -2 | mA | VBP = 5.0 V, VDS ≥ 36 V | 7 |
| BYPASS Pin Voltage | VBP | 5.075 | 5.22 | 5.35 | V | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 7 |
| BYPASS Pin Shunt Voltage | VBP(SHUNT) | 5.2 | 5.39 | 5.55 | V | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 8 |
| BYPASS Pin Power-Up Reset Threshold Voltage | VBP(RESET) | 4.35 | 4.5 | 4.65 | V | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 8 |
| Current Limit for Auto-Restart (LYT1x03) | ILIMIT(AR) | 1.06 | 1.15 | 1.24 | A | di/dt = 446 mA/µs; TJ = 25 °C | 8 |
| Fault Minimum Switch ON-Time | TFAULT(MIN) | 250 | | 400 | ns | SOURCE = 0 V; TJ = -40 °C to 125 °C (unless otherwise specified) | 8 |
| Input Overvoltage Threshold | IIOV | 0.9 | 1 | 1.1 | mA | TJ = 25 °C | 8 |
| MULTIFUNCTIONAL Pin Auto-Restart Threshold Voltage (Output OVP) | VOOV | 2.3 | 2.4 | 2.48 | V | TJ = 25 °C | 8 |
| MULTIFUNCTIONAL Pin Undervoltage Threshold (Output Short) | VOUV | 0.91 | 0.95 | 0.99 | V | TJ = 25 °C; See Note B | 8 |
| Junction Temperature at Fold-Back | TFB | 138 | 145 | 152 | °C | See Note B | 8 |
| ON-State Resistance (LYT1x03, TJ = 25 °C) | RDS(ON) | | 4.5 | 5.2 | Ω | ID = 139 mA; TJ = 25 °C | 9 |
| ON-State Resistance (LYT1x03, TJ = 100 °C) | RDS(ON) | | 6.8 | 7.8 | Ω | ID = 139 mA; TJ = 100 °C | 9 |
| DRAIN Pin Voltage | | -0.3 | | 725 | V | | 7 |
| DRAIN Pin Peak Current (LYT1x03, higher allowed value) | | | | 2.6 | A | Allowed while DRAIN voltage is simultaneously less than 400 V | 7 |
| BYPASS Pin Voltage (absolute maximum) | | -0.3 | | 6 | V | | 7 |
| MULTIFUNCTION, FEEDBACK Pin Voltage | | -0.45 | | 7 | V | | 7 |
| Lead Temperature | | | | 260 | °C | | 7 |
| Storage Temperature | | -65 | | 150 | °C | | 7 |
| Operating Junction Temperature | | -40 | | 150 | °C | See Note 4 (normally limited by internal circuitry) | 7 |
| MULTIFUNCTION Pin Steady-State Operation Voltage Range | | 1 | | 2.4 | V | Mode 1: FET OFF | 2 |
| Thermal Resistance Junction-to-Ambient (0.36 sq. in. copper) | θJA | | 100 | | °C/W | Soldered to 0.36 sq. inch (232 mm2) 2 oz. copper clad, no external heat sink | 7 |
| Thermal Resistance Junction-to-Ambient (1 sq. in. copper) | θJA | | 80 | | °C/W | Soldered to 1 sq. in. (645 mm2) 2 oz. copper clad | 7 |
| Thermal Resistance Junction-to-Case (SOURCE pin) | θJC | | 30 | | °C/W | Measured on the SOURCE pin close to plastic interface | 7 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | ground potential SOURCE pins are used for heat sinking. This allows the designer to maximize the copper area for good thermal management but, without having the risk of increased EMI. | 5 |
## CAD (KiCad official)
- Symbol: `LYT1603D-TL`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SO-8 (KiCad packages3D, STEP)
- 3D model files: `lyt1603d-tl-etched.step` / `lyt1603d-tl-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lyt1603d-tl.step` / `lyt1603d-tl.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [POWER INTEGRATIONS datasheet](docs/lyt1603d-tl-datasheet.pdf) (14 pp, sha256 `c25fe052456356af`, retrieved 2026-10-30, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lyt1603d-tl-datasheet.pdf)