Generated by kicad-footprint-generator · KiCad file format 20260206
LTC6995IS6-1#TRMPBF
Analog Devices · Timers / Clock Oscillators · TSOT-23-6
LTC6995IS6-1#TRMPBF from Analog Devices, in a TSOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RST | input | Active-high output reset on the LTC6995-1 that stops the master oscillator and clears the internal dividers, with VIH of 0.7 • V+ minimum and VIL of 0.3 • V+ maximum. |
| 2 | GND | power_in | Ground; the datasheet says to tie it to a low-inductance ground plane for best performance. |
| 3 | SET | input | Frequency-setting input regulated to 1V above GND, with ISET range of 1.25µA to 20µA; oscillation stops if ISET drops below about 500nA, and capacitance on this pin must be kept below 10pF. |
| 4 | DIV | input | Programmable divider and polarity input whose voltage is digitized by a 4-bit A/D referenced to V+ to set DIVCODE, with capacitance limited to less than 100pF. |
| 5 | V+ | power_in | Supply voltage of 2.25V to 5.5V that should be kept free from noise and ripple and bypassed directly to GND with a 0.1µF capacitor. |
| 6 | OUT | output | Oscillator output that swings from GND to V+ with an output resistance of about 30Ω, and a series resistor should be used to limit source/sink current to 20mA when driving an LED or other low-impedance load. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSOT-23-6 |
| Category | Clock and Timing |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Frequency Accuracy | ∆fOUT | -2.2 | 2.2 | % | 29.1µHz ≤ fOUT ≤ 977Hz; full operating temperature range (l) | 3 | |
| Frequency Accuracy | ∆fOUT | -1.5 | 1.5 | % | 29.1µHz ≤ fOUT ≤ 977Hz | 3 | |
| Frequency Drift Over Temperature | ∆fOUT/∆T | -0.005 | 0.005 | %/°C | Full operating temperature range (l) | 3 | |
| Frequency Drift Over Supply | ∆fOUT/∆V+ | 0.23 | 0.55 | %/V | V+ = 4.5V to 5.5V (l) | 3 | |
| Frequency Drift Over Supply | ∆fOUT/∆V+ | 0.06 | 0.16 | %/V | V+ = 2.25V to 4.5V (l) | 3 | |
| Voltage at SET Pin | VSET | 0.97 | 1 | 1.03 | V | Full operating temperature range (l) | 3 |
| VSET Drift Over Temperature | ∆VSET/∆T | -75 | 75 | µV/°C | Full operating temperature range (l) | 3 | |
| Frequency-Setting Resistor | RSET | 50 | 800 | kΩ | Full operating temperature range (l) | 3 | |
| DIV Pin Voltage | VDIV | 0 | V | Full operating temperature range (l); max printed as V+ | 3 | ||
| DIV Pin Valid Code Range Deviation from Ideal | ∆VDIV/∆V+ | -1.5 | 1.5 | % | VDIV/V+ = (DIVCODE + 0.5)/16; (l) | 3 | |
| DIV Pin Input Current | -10 | 10 | nA | Full operating temperature range (l) | 3 | ||
| V+ Operating Supply Voltage Range | V+ | 2.25 | 5.5 | V | Full operating temperature range (l) | 3 | |
| Power-On Reset Voltage | 1.95 | V | Full operating temperature range (l) | 3 | |||
| Supply Current | IS | 135 | 170 | µA | RL = ∞, RSET = 50k, V+ = 5.5V (l) | 3 | |
| Supply Current | IS | 105 | 135 | µA | RL = ∞, RSET = 50k, V+ = 2.25V (l) | 3 | |
| Supply Current | IS | 100 | 130 | µA | RL = ∞, RSET = 100k, V+ = 5.5V (l) | 3 | |
| Supply Current | IS | 80 | 105 | µA | RL = ∞, RSET = 100k, V+ = 2.25V (l) | 3 | |
| Supply Current | IS | 65 | 100 | µA | RL = ∞, RSET = 800k, V+ = 5.5V (l) | 3 | |
| Supply Current | IS | 55 | 85 | µA | RL = ∞, RSET = 800k, V+ = 2.25V (l) | 3 | |
| RST Pin Input Current | -10 | 10 | nA | RST = 0V to V+ (l) | 4 | ||
| High Level RST Pin Input Voltage | VIH | 0.7 | •V+ | Note 6; printed as 0.7 • V+ | 4 | ||
| Low Level RST Pin Input Voltage | VIL | 0.3 | •V+ | Note 6; printed as 0.3 • V+ | 4 | ||
| Output Current | IOUT(MAX) | -20 | 20 | mA | V+ = 2.7V to 5.5V | 4 | |
| High Level Output Voltage | VOH | 5.45 | 5.48 | V | V+ = 5.5V, IOUT = -1mA (l) | 4 | |
| High Level Output Voltage | VOH | 4.84 | 5.15 | V | V+ = 5.5V, IOUT = -16mA (l) | 4 | |
| High Level Output Voltage | VOH | 3.24 | 3.27 | V | V+ = 3.3V, IOUT = -1mA (l) | 4 | |
| High Level Output Voltage | VOH | 2.75 | 2.99 | V | V+ = 3.3V, IOUT = -10mA (l) | 4 | |
| High Level Output Voltage | VOH | 2.17 | 2.21 | V | V+ = 2.25V, IOUT = -1mA (l) | 4 | |
| High Level Output Voltage | VOH | 1.58 | 1.88 | V | V+ = 2.25V, IOUT = -8mA (l) | 4 | |
| Low Level Output Voltage | VOL | 0.02 | 0.04 | V | V+ = 5.5V, IOUT = 1mA (l) | 4 | |
| Low Level Output Voltage | VOL | 0.26 | 0.54 | V | V+ = 5.5V, IOUT = 16mA (l) | 4 | |
| Low Level Output Voltage | VOL | 0.03 | 0.05 | V | V+ = 3.3V, IOUT = 1mA (l) | 4 | |
| Low Level Output Voltage | VOL | 0.22 | 0.46 | V | V+ = 3.3V, IOUT = 10mA (l) | 4 | |
| Low Level Output Voltage | VOL | 0.03 | 0.07 | V | V+ = 2.25V, IOUT = 1mA (l) | 4 | |
| Minimum Input Pulse Width | tWIDTH | 5 | ns | V+ = 3.3V | 4 | ||
| Supply Voltage (V+) to GND | V+ | 6 | V | 2 | |||
| Operating Temperature Range LTC6995I | -40 | 85 | °C | LTC6995I (Note 2) | 2 | ||
| Specified Temperature Range LTC6995I | -40 | 85 | °C | LTC6995I, Note 3 | 2 | ||
| Junction Temperature | TJ | 150 | °C | 2 | |||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Thermal Resistance Junction-to-Ambient | θJA | 192 | °C/W | S6 package (TSOT-23) | 2 | ||
| Thermal Resistance Junction-to-Case | θJC | 51 | °C/W | S6 package (TSOT-23) | 2 | ||
| SET Pin Current Range | ISET | 1.25 | 20 | µA | Recommended frequency-setting current | 7 | |
| RST Pin Input Capacitance | 2.5 | pF | 4 | ||||
| Reset Propagation Delay | tRST | 16 | ns | V+ = 5.5V | 4 | ||
| Reset Propagation Delay | tRST | 24 | ns | V+ = 3.3V | 4 | ||
| Reset Propagation Delay | tRST | 40 | ns | V+ = 2.25V | 4 | ||
| Period Jitter | 15 | ppmRMS | NDIV = 1 (Note 10) | 3 | |||
| Period Jitter | 7 | ppmRMS | NDIV = 8 (Note 10) | 3 | |||
| Long-Term Frequency Stability | 90 | ppm/√kHr | Note 11, tested at 30°C | 3 | |||
| Frequency Change Settling Time | tS | 1 | Cycle | Note 9 | 3 | ||
| Supply Current | IS | 60 | µA | RL = ∞, ISET = 0µA, V+ = 5.5V | 3 | ||
| Supply Current | IS | 52 | µA | RL = ∞, ISET = 0µA, V+ = 2.25V | 3 |
CAD (KiCad official)
- Symbol:
LTC6995IS6-1#TRMPBF - Footprint:
Package_TO_SOT_SMD:TSOT-23-6 - 3D model: TSOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
ltc6995is6-1-trmpbf-etched.step/ltc6995is6-1-trmpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc6995is6-1-trmpbf.step/ltc6995is6-1-trmpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
01f16c9dda1e78a2, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).