main
Ray
Publish 0.1.0
6a6c424
LTC6994IDCB-1#TRMPBF
Analog Devices · Delay Lines · DFN-6-EP(2x3)
LTC6994IDCB-1#TRMPBF from Analog Devices, in a DFN-6-EP(2x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V+ | power_in | Supply voltage range is 2.25V to 5.5V; keep it free from noise and ripple and bypass it directly to GND with a 0.1µF capacitor. |
| 2 | DIV | input | Programmable divider and polarity input whose voltage is converted to a 4-bit DIVCODE, with 1% resistors recommended for an accurate result and capacitance limited to less than 100pF. |
| 3 | SET | input | Delay setting input regulated to 1V above GND, with ISET programmable from 1.25µA to 20µA, and the delayed output does not occur if ISET drops below approximately 500nA. |
| 4 | IN | input | Logic input whose rising or falling edges propagate to OUT after a programmable delay; the LTC6994-1 delays only one edge while the LTC6994-2 delays both edges. |
| 5 | GND | power_in | Ground pin that should be tied to a low inductance ground plane for best performance. |
| 6 | OUT | output | Output swings from GND to V+ with an output resistance of approximately 30Ω, and a series resistor should be used to limit source/sink current to 20mA when driving an LED or low impedance load. |
| 7 | EP | power_in | Exposed pad connected to GND internally, with PCB connection optional. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-6-EP(2x3) |
| Category | Clock and Timing |
| Pins | 7 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| V+ Operating Supply Voltage Range | V+ | 2.25 | 5.5 | V | 4 | ||
| Supply Voltage (V+) to GND | V+ | 6 | V | V+ to GND | 2 | ||
| Operating Temperature Range LTC6994I | -40 | 85 | °C | LTC6994I | 2 | ||
| Junction Temperature | TJ | 150 | °C | 2 | |||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 64 | °C/W | DCB package | 2 | ||
| Thermal Resistance Junction-to-Case | θJC | 10.6 | °C/W | DCB package | 2 | ||
| Delay Accuracy | ∆tDELAY | -2.3 | 2.3 | % | NDIV ≥ 512 | 3 | |
| Delay Accuracy | ∆tDELAY | -3 | 3 | % | NDIV ≥ 512, l (full operating temperature range) | 3 | |
| Delay Accuracy | ∆tDELAY | -3.4 | 3.4 | % | 8 ≤ NDIV ≤ 64 | 3 | |
| Delay Accuracy | ∆tDELAY | -4.4 | 4.4 | % | 8 ≤ NDIV ≤ 64, l (full operating temperature range) | 3 | |
| Delay Accuracy | ∆tDELAY | -5.1 | 5.1 | % | NDIV = 1 | 3 | |
| Delay Accuracy | ∆tDELAY | -6.2 | 6.2 | % | NDIV = 1, l (full operating temperature range) | 3 | |
| Delay Drift Over Temperature | ∆tDELAY/∆T | -0.006 | 0.006 | %/°C | NDIV ≥ 512 | 3 | |
| Delay Drift Over Temperature | ∆tDELAY/∆T | -0.008 | 0.008 | %/°C | NDIV ≤ 64 | 3 | |
| Power-On Reset Voltage | 1.95 | V | l | 4 | |||
| Supply Current (Idle) | IS(IDLE) | 165 | 200 | µA | RL = ∞, RSET = 50k, NDIV ≤ 64, V+ = 5.5V | 4 | |
| Supply Current (Idle) | IS(IDLE) | 125 | 160 | µA | RL = ∞, RSET = 50k, NDIV ≤ 64, V+ = 2.25V | 4 | |
| Supply Current (Idle) | IS(IDLE) | 135 | 175 | µA | RL = ∞, RSET = 50k, NDIV ≥ 512, V+ = 5.5V | 4 | |
| Supply Current (Idle) | IS(IDLE) | 105 | 140 | µA | RL = ∞, RSET = 50k, NDIV ≥ 512, V+ = 2.25V | 4 | |
| Supply Current (Idle) | IS(IDLE) | 70 | 110 | µA | RL = ∞, RSET = 800k, NDIV ≤ 64, V+ = 5.5V | 4 | |
| Supply Current (Idle) | IS(IDLE) | 60 | 95 | µA | RL = ∞, RSET = 800k, NDIV ≤ 64, V+ = 2.25V | 4 | |
| Supply Current (Idle) | IS(IDLE) | 65 | 100 | µA | RL = ∞, RSET = 800k, NDIV ≥ 512, V+ = 5.5V | 4 | |
| Supply Current (Idle) | IS(IDLE) | 55 | 90 | µA | RL = ∞, RSET = 800k, NDIV ≥ 512, V+ = 2.25V | 4 | |
| Voltage at SET Pin | VSET | 0.97 | 1 | 1.03 | V | l | 4 |
| VSET Drift Over Temperature | ∆VSET/∆T | -75 | 75 | µV/°C | l | 4 | |
| Frequency-Setting Resistor | RSET | 50 | 800 | kΩ | l | 4 | |
| DIV Pin Valid Code Range Deviation from Ideal | ∆VDIV/∆V+ | -1.5 | 1.5 | % | VDIV/V+ = (DIVCODE + 0.5)/16, l | 4 | |
| DIV Pin Input Current | -10 | 10 | nA | l | 4 | ||
| IN Pin Input Current | -10 | 10 | nA | IN = 0V to V+ | 4 | ||
| Output Current | IOUT(MAX) | -20 | 20 | mA | V+ = 2.7V to 5.5V | 4 |
CAD (KiCad official)
- Symbol:
LTC6994IDCB-1#TRMPBF - Footprint:
Package_DFN_QFN:DFN-6-1EP_3x2mm_P0.5mm_EP1.65x1.35mm - 3D model: DFN-6-EP(2x3) (KiCad packages3D, STEP)
- 3D model files:
ltc6994idcb-1-trmpbf-etched.step/ltc6994idcb-1-trmpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc6994idcb-1-trmpbf.step/ltc6994idcb-1-trmpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
ddc7413e4b6e837f, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LTC6994IDCB-1#TRMPBF
**Analog Devices** · Delay Lines · DFN-6-EP(2x3)
LTC6994IDCB-1#TRMPBF from Analog Devices, in a DFN-6-EP(2x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V+ | power_in | Supply voltage range is 2.25V to 5.5V; keep it free from noise and ripple and bypass it directly to GND with a 0.1µF capacitor. |
| 2 | DIV | input | Programmable divider and polarity input whose voltage is converted to a 4-bit DIVCODE, with 1% resistors recommended for an accurate result and capacitance limited to less than 100pF. |
| 3 | SET | input | Delay setting input regulated to 1V above GND, with ISET programmable from 1.25µA to 20µA, and the delayed output does not occur if ISET drops below approximately 500nA. |
| 4 | IN | input | Logic input whose rising or falling edges propagate to OUT after a programmable delay; the LTC6994-1 delays only one edge while the LTC6994-2 delays both edges. |
| 5 | GND | power_in | Ground pin that should be tied to a low inductance ground plane for best performance. |
| 6 | OUT | output | Output swings from GND to V+ with an output resistance of approximately 30Ω, and a series resistor should be used to limit source/sink current to 20mA when driving an LED or low impedance load. |
| 7 | EP | power_in | Exposed pad connected to GND internally, with PCB connection optional. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-6-EP(2x3) |
| Category | Clock and Timing |
| Pins | 7 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| V+ Operating Supply Voltage Range | V+ | 2.25 | | 5.5 | V | | 4 |
| Supply Voltage (V+) to GND | V+ | | | 6 | V | V+ to GND | 2 |
| Operating Temperature Range LTC6994I | | -40 | | 85 | °C | LTC6994I | 2 |
| Junction Temperature | TJ | | | 150 | °C | | 2 |
| Storage Temperature Range | TSTG | -65 | | 150 | °C | | 2 |
| Thermal Resistance Junction-to-Ambient | θJA | | 64 | | °C/W | DCB package | 2 |
| Thermal Resistance Junction-to-Case | θJC | | 10.6 | | °C/W | DCB package | 2 |
| Delay Accuracy | ∆tDELAY | -2.3 | | 2.3 | % | NDIV ≥ 512 | 3 |
| Delay Accuracy | ∆tDELAY | -3 | | 3 | % | NDIV ≥ 512, l (full operating temperature range) | 3 |
| Delay Accuracy | ∆tDELAY | -3.4 | | 3.4 | % | 8 ≤ NDIV ≤ 64 | 3 |
| Delay Accuracy | ∆tDELAY | -4.4 | | 4.4 | % | 8 ≤ NDIV ≤ 64, l (full operating temperature range) | 3 |
| Delay Accuracy | ∆tDELAY | -5.1 | | 5.1 | % | NDIV = 1 | 3 |
| Delay Accuracy | ∆tDELAY | -6.2 | | 6.2 | % | NDIV = 1, l (full operating temperature range) | 3 |
| Delay Drift Over Temperature | ∆tDELAY/∆T | -0.006 | | 0.006 | %/°C | NDIV ≥ 512 | 3 |
| Delay Drift Over Temperature | ∆tDELAY/∆T | -0.008 | | 0.008 | %/°C | NDIV ≤ 64 | 3 |
| Power-On Reset Voltage | | | | 1.95 | V | l | 4 |
| Supply Current (Idle) | IS(IDLE) | | 165 | 200 | µA | RL = ∞, RSET = 50k, NDIV ≤ 64, V+ = 5.5V | 4 |
| Supply Current (Idle) | IS(IDLE) | | 125 | 160 | µA | RL = ∞, RSET = 50k, NDIV ≤ 64, V+ = 2.25V | 4 |
| Supply Current (Idle) | IS(IDLE) | | 135 | 175 | µA | RL = ∞, RSET = 50k, NDIV ≥ 512, V+ = 5.5V | 4 |
| Supply Current (Idle) | IS(IDLE) | | 105 | 140 | µA | RL = ∞, RSET = 50k, NDIV ≥ 512, V+ = 2.25V | 4 |
| Supply Current (Idle) | IS(IDLE) | | 70 | 110 | µA | RL = ∞, RSET = 800k, NDIV ≤ 64, V+ = 5.5V | 4 |
| Supply Current (Idle) | IS(IDLE) | | 60 | 95 | µA | RL = ∞, RSET = 800k, NDIV ≤ 64, V+ = 2.25V | 4 |
| Supply Current (Idle) | IS(IDLE) | | 65 | 100 | µA | RL = ∞, RSET = 800k, NDIV ≥ 512, V+ = 5.5V | 4 |
| Supply Current (Idle) | IS(IDLE) | | 55 | 90 | µA | RL = ∞, RSET = 800k, NDIV ≥ 512, V+ = 2.25V | 4 |
| Voltage at SET Pin | VSET | 0.97 | 1 | 1.03 | V | l | 4 |
| VSET Drift Over Temperature | ∆VSET/∆T | -75 | | 75 | µV/°C | l | 4 |
| Frequency-Setting Resistor | RSET | 50 | | 800 | kΩ | l | 4 |
| DIV Pin Valid Code Range Deviation from Ideal | ∆VDIV/∆V+ | -1.5 | | 1.5 | % | VDIV/V+ = (DIVCODE + 0.5)/16, l | 4 |
| DIV Pin Input Current | | -10 | | 10 | nA | l | 4 |
| IN Pin Input Current | | -10 | | 10 | nA | IN = 0V to V+ | 4 |
| Output Current | IOUT(MAX) | -20 | | 20 | mA | V+ = 2.7V to 5.5V | 4 |
## CAD (KiCad official)
- Symbol: `LTC6994IDCB-1#TRMPBF`
- Footprint: `Package_DFN_QFN:DFN-6-1EP_3x2mm_P0.5mm_EP1.65x1.35mm`
- 3D model: DFN-6-EP(2x3) (KiCad packages3D, STEP)
- 3D model files: `ltc6994idcb-1-trmpbf-etched.step` / `ltc6994idcb-1-trmpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ltc6994idcb-1-trmpbf.step` / `ltc6994idcb-1-trmpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/LTC6994-1-6994-2.pdf) (28 pp, sha256 `ddc7413e4b6e837f`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ltc6994idcb-1-trmpbf-datasheet.pdf)