3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLTC6990HS6#TRMPBF
Analog Devices · Timers / Clock Oscillators · TSOT-23-6
LTC6990HS6#TRMPBF from Analog Devices, in a TSOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OE | input | Output enable: driving OE low disables the output asynchronously, forcing it low (Hi-Z = 0) or floating it (Hi-Z = 1), and when re-enabled the output may stay low briefly to synchronize with the internal oscillator. |
| 2 | GND | power_in | Ground; tie to a low-inductance ground plane for best performance. |
| 3 | SET | input | Frequency-setting input regulated to 1V above GND, with ISET programmable from 1.25µA to 40µA; oscillation stops if ISET falls below approximately 500nA, and the SET pin capacitance should be kept below 10pF. |
| 4 | DIV | input | Programmable divider and Hi-Z mode input whose voltage is digitized by a V+-referenced A/D converter into a 4-bit DIVCODE; its MSB sets the output behavior when disabled, and the capacitance on this pin should be limited to less than 100pF. |
| 5 | V+ | power_in | Supply voltage of 2.25V to 5.5V that must be kept free from noise and ripple and bypassed directly to GND with a 0.1µF capacitor. |
| 6 | OUT | output | Oscillator output swinging from GND to V+ with an output resistance of approximately 30Ω; a series resistor should be used when driving an LED or other low-impedance load to limit source/sink current to 20mA. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSOT-23-6 |
| Category | Clock and Timing |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (V+) to GND | V+ | 6 | V | 2 | |||
| Operating Temperature Range (LTC6990H grade) | -40 | 125 | °C | LTC6990H, specified temperature range | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Junction Temperature | TJMAX | 150 | °C | 2 | |||
| Thermal Resistance Junction-to-Ambient (S6 TSOT-23) | θJA | 192 | °C/W | S6 TSOT-23 package | 2 | ||
| Thermal Resistance Junction-to-Case (S6 TSOT-23) | θJC | 51 | °C/W | S6 TSOT-23 package | 2 | ||
| Output Frequency (recommended range) | fOUT | 0.488 | 1000 | kHz | Recommended Range: RSET = 50k to 800k | 3 | |
| Output Frequency (extended range) | fOUT | 0.488 | 2000 | kHz | Extended Range: RSET = 25k to 800k | 3 | |
| Frequency Accuracy (recommended range) | ∆fOUT | -1.5 | 1.5 | % | Recommended Range: RSET = 50k to 800k; l (full temperature range) | 3 | |
| Frequency Accuracy (extended range) | ∆fOUT | -3.2 | 3.2 | % | Extended Range: RSET = 25k to 800k; l (full temperature range) | 3 | |
| Frequency Drift Over Temperature | ∆fOUT/∆T | -0.005 | 0.005 | %/°C | Over temperature (l) | 3 | |
| Frequency Drift Over Supply | ∆fOUT/∆V+ | 0.23 | 0.55 | %/V | V+ = 4.5V to 5.5V (l) | 3 | |
| Frequency Drift Over Supply | ∆fOUT/∆V+ | 0.06 | 0.16 | %/V | V+ = 2.25V to 4.5V (l) | 3 | |
| Duty Cycle | 47 | 50 | 53 | % | NDIV = 1, RSET = 25k to 800k (l) | 3 | |
| Duty Cycle | 48 | 50 | 52 | % | NDIV > 1, RSET = 25k to 800k (l) | 3 | |
| Voltage at SET Pin | VSET | 0.97 | 1 | 1.03 | V | (l) | 3 |
| VSET Drift Over Temperature | ∆VSET/∆T | -75 | 75 | µV/°C | (l) | 3 | |
| Frequency-Setting Resistor (recommended range) | RSET | 50 | 800 | kΩ | Recommended range (l) | 3 | |
| Frequency-Setting Resistor (extended range) | RSET | 25 | 800 | kΩ | Extended range (l) | 3 | |
| DIV Pin Voltage | VDIV | 0 | V | (l); printed maximum is V+ (not a number) | 3 | ||
| DIV Pin Valid Code Range Deviation | ∆VDIV/V+ | -1.5 | 1.5 | % | Deviation from ideal VDIV/V+ = (DIVCODE + 0.5)/16 (l) | 3 | |
| DIV Pin Input Current | -10 | 10 | nA | (l) | 3 | ||
| V+ Operating Supply Voltage Range | V+ | 2.25 | 5.5 | V | (l) | 3 | |
| Supply Current | IS | 235 | 283 | µA | RL = ∞, NDIV = 1, RSET = 50k, V+ = 5.5V (l) | 3 | |
| Supply Current | IS | 145 | 183 | µA | RL = ∞, NDIV = 1, RSET = 50k, V+ = 2.25V (l) | 3 | |
| Supply Current | IS | 71 | 105 | µA | RL = ∞, NDIV = 1, RSET = 800k, V+ = 5.5V (l) | 3 | |
| Supply Current | IS | 59 | 92 | µA | RL = ∞, NDIV = 1, RSET = 800k, V+ = 2.25V (l) | 3 | |
| Supply Current | IS | 137 | 180 | µA | RL = ∞, NDIV = 128, RSET = 50k, V+ = 5.5V (l) | 3 | |
| Supply Current | IS | 106 | 145 | µA | RL = ∞, NDIV = 128, RSET = 50k, V+ = 2.25V (l) | 3 | |
| Supply Current | IS | 66 | 100 | µA | RL = ∞, NDIV = 128, RSET = 800k, V+ = 5.5V (l) | 3 | |
| Supply Current | IS | 56 | 90 | µA | RL = ∞, NDIV = 128, RSET = 800k, V+ = 2.25V (l) | 3 | |
| OE Pin Input Current | -10 | 10 | nA | OE = 0V to V+ (l) | 4 | ||
| OUT Pin Hi-Z Leakage | -10 | 10 | µA | OE = 0V, DIVCODE ≥ 8, OUT = 0V to V+ | 4 | ||
| Maximum Output Current | IOUT(MAX) | -20 | 20 | mA | 4 | ||
| High Level Output Voltage | VOH | 5.45 | 5.48 | V | V+ = 5.5V, IOH = -1mA (l) | 4 | |
| High Level Output Voltage | VOH | 4.84 | 5.15 | V | V+ = 5.5V, IOH = -16mA (l) | 4 | |
| High Level Output Voltage | VOH | 3.24 | 3.27 | V | V+ = 3.3V, IOH = -1mA (l) | 4 | |
| High Level Output Voltage | VOH | 2.75 | 2.99 | V | V+ = 3.3V, IOH = -10mA (l) | 4 | |
| High Level Output Voltage | VOH | 2.17 | 2.21 | V | V+ = 2.25V, IOH = -1mA (l) | 4 | |
| High Level Output Voltage | VOH | 1.58 | 1.88 | V | V+ = 2.25V, IOH = -8mA (l) | 4 | |
| Low Level Output Voltage | VOL | 0.02 | 0.04 | V | V+ = 5.5V, IOL = 1mA (l) | 4 | |
| Low Level Output Voltage | VOL | 0.26 | 0.54 | V | V+ = 5.5V, IOL = 16mA (l) | 4 | |
| Low Level Output Voltage | VOL | 0.03 | 0.05 | V | V+ = 3.3V, IOL = 1mA (l) | 4 | |
| Low Level Output Voltage | VOL | 0.22 | 0.46 | V | V+ = 3.3V, IOL = 10mA (l) | 4 | |
| Low Level Output Voltage | VOL | 0.03 | 0.07 | V | V+ = 2.25V, IOL = 1mA (l) | 4 | |
| Period Jitter | 0.38 | %P-P | NDIV = 1 | 3 | |||
| Period Jitter | 0.22 | %P-P | NDIV = 2 | 3 | |||
| Period Jitter | 0.027 | %RMS | NDIV = 2 | 3 | |||
| Period Jitter | 0.022 | %P-P | NDIV = 128 | 3 | |||
| Period Jitter | 0.004 | %RMS | NDIV = 128 | 3 | |||
| Power-On Reset Voltage | 1.95 | V | RSET = 25k to 800k (l) | 3 |
CAD (KiCad official)
- Symbol:
LTC6990HS6#TRMPBF - Footprint:
Package_TO_SOT_SMD:TSOT-23-6 - 3D model: TSOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
ltc6990hs6-trmpbf-etched.step/ltc6990hs6-trmpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc6990hs6-trmpbf.step/ltc6990hs6-trmpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (30 pp, sha256
57c3612930febe0d, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).