main
Ray
Publish 0.1.0
b3b40fc
LTC6906CS6#TRPBF
Analog Devices · Timers / Clock Oscillators · TSOT-23-6
LTC6906CS6#TRPBF from Analog Devices, in a TSOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | output | Oscillator output that swings from GND to V+ through an output resistance of approximately 150Ω; keep the load resistance as high as possible and the load capacitance as low as possible for micropower operation. |
| 2 | GND | power_in | Ground reference pin for the device. |
| 3 | DIV | input | Three-level divider select input: tie to GND for ÷1, leave floating for ÷3, or tie to V+ for ÷10; when floating it is pulled to mid-supply through 2.5MΩ and should be shielded from OUT coupling. |
| 4 | SET | passive | Frequency-setting resistor input: connect RSET (100kΩ to 1MΩ) from this pin to GND, keep capacitance in parallel with RSET below 10pF, and note the SET voltage is approximately 650mV, decreasing about 2.2mV/°C. |
| 5 | GRD | output | Guard signal held within a few millivolts of the SET pin voltage (VGRD relative to VSET limited to ±10mV) to shunt PC board leakage away from SET; route a bare copper trace with no solder mask around SET. |
| 6 | V+ | power_in | Supply voltage input of 2.25V to 3.6V, internally decoupled by a 20Ω resistor in series with an 800pF capacitor, and it should be kept reasonably free of noise and ripple. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSOT-23-6 |
| Category | Clock and Timing |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Frequency Accuracy (LTC6906C), 100kHz ≤ f ≤ 1MHz | Δf | -0.65 | 0.65 | % | V+ = 2.7V to 3.6V, LTC6906C | 2 | |
| Frequency Accuracy (LTC6906C), 100kHz ≤ f ≤ 1MHz | Δf | -0.85 | 0.85 | % | V+ = 2.25V, LTC6906C | 2 | |
| Frequency Accuracy, 100kHz ≤ f ≤ 1MHz | Δf | -0.5 | 0.25 | 0.5 | % | V+ = 2.7V to 3.6V | 2 |
| Frequency Accuracy, 100kHz ≤ f ≤ 1MHz | Δf | -0.7 | 0.25 | 0.7 | % | V+ = 2.25V | 2 |
| Frequency-Setting Resistor Range | RSET | 100 | 1000 | kΩ | 3 | ||
| Frequency Drift Over Temperature | Δf/ΔT | -0.005 | 0.005 | %/°C | RSET = 316k | 3 | |
| Frequency Drift Over Supply | Δf/ΔV | 0.06 | %/V | V+ = 2.25V to 3.6V, 100k ≤ RSET ≤ 1000k | 3 | ||
| Timing Jitter | 0.03 | % | Pin 3 = V+, 100k ≤ RSET ≤ 1000k | 3 | |||
| Timing Jitter | 0.07 | % | Pin 3 = Open, 100k ≤ RSET ≤ 1000k | 3 | |||
| Timing Jitter | 0.15 | % | Pin 3 = 0V, 100k ≤ RSET ≤ 1000k | 3 | |||
| Long-Term Stability of Output Frequency | Sf | 300 | ppm/√kHr | Pin 3 = V+ | 3 | ||
| DC Duty Cycle | 45 | 50 | 55 | % | 3 | ||
| V+ Operating Supply Range | V+ | 2.25 | 3.6 | V | 3 | ||
| Power Supply Current (DIV=1, fOUT=100kHz) | IS | 12.5 | 18 | μA | RSET = 1000k, Pin 3 = 0V, RL = 10M, V+ = 3.6V | 3 | |
| Power Supply Current (DIV=1, fOUT=100kHz) | IS | 10 | 15 | μA | RSET = 1000k, Pin 3 = 0V, RL = 10M, V+ = 2.25V | 3 | |
| Power Supply Current (DIV=1, fOUT=1MHz) | IS | 78 | 100 | μA | RSET = 100k, Pin 3 = 0V, RL = 10M, V+ = 3.6V | 3 | |
| Power Supply Current (DIV=1, fOUT=1MHz) | IS | 60 | 80 | μA | RSET = 100k, Pin 3 = 0V, RL = 10M, V+ = 2.25V | 3 | |
| High Level DIV Input Voltage | VIH | 3.1 | V | V+ = 3.6V | 3 | ||
| High Level DIV Input Voltage | VIH | 2.05 | V | V+ = 2.25V | 3 | ||
| Low Level DIV Input Voltage | VIL | 0.5 | V | V+ = 3.6V | 3 | ||
| Low Level DIV Input Voltage | VIL | 0.2 | V | V+ = 2.25V | 3 | ||
| DIV Input Current | IDIV | -2 | -1 | μA | Pin 3 = V+ | 3 | |
| DIV Input Current | IDIV | 1 | 2 | μA | Pin 3 = 0V | 3 | |
| High Level Output Voltage | VOH | 3.4 | 3.59 | V | V+ = 3.6V, IOH = -100μA | 3 | |
| High Level Output Voltage | VOH | 2.8 | 3.3 | V | V+ = 3.6V, IOH = -1mA | 3 | |
| High Level Output Voltage | VOH | 2.15 | 2.2 | V | V+ = 2.25V, IOH = -100μA | 3 | |
| High Level Output Voltage | VOH | 1.75 | 2 | V | V+ = 2.25V, IOH = -1mA | 3 | |
| Low Level Output Voltage | VOL | 0.02 | 0.2 | V | V+ = 3.6V, IOL = 100μA | 3 | |
| Low Level Output Voltage | VOL | 0.15 | 0.8 | V | V+ = 3.6V, IOL = 1mA | 3 | |
| Low Level Output Voltage | VOL | 0.03 | 0.1 | V | V+ = 2.25V, IOL = 100μA | 3 | |
| Low Level Output Voltage | VOL | 0.3 | 0.5 | V | V+ = 2.25V, IOL = 1mA | 3 | |
| OUT Rise Time | tr | 10 | ns | V+ = 3.6V | 3 | ||
| OUT Rise Time | tr | 25 | ns | V+ = 2.25V | 3 | ||
| OUT Fall Time | tf | 10 | ns | V+ = 3.6V | 3 | ||
| OUT Fall Time | tf | 25 | ns | V+ = 2.25V | 3 | ||
| GRD Pin Voltage Relative to SET Pin Voltage | VGS | -10 | 10 | mV | -10μA ≤ IGRD ≤ 0.3μA | 3 | |
| V+ Absolute Maximum Supply Voltage | V+ | -0.3 | 6 | V | 2 | ||
| DIV to GND Voltage | DIV | -0.3 | V | Max is V+ + 0.3V | 2 | ||
| SET to GND Voltage | SET | -0.3 | V | Max is V+ + 0.3V | 2 | ||
| GRD to GND Voltage | GRD | -0.3 | V | Max is V+ + 0.3V | 2 | ||
| Operating Temperature Range (LTC6906C) | TA | -40 | 85 | °C | 2 | ||
| Specified Temperature Range (LTC6906C) | TA | 0 | 70 | °C | Guaranteed performance range | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Lead Temperature (Soldering) | 300 | °C | 10 sec | 2 | |||
| Maximum Junction Temperature | TJMAX | 150 | °C | 2 | |||
| Thermal Resistance, Junction to Ambient | θJA | 230 | °C/W | S6 package | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | SET pin and shunts leakage current away from the SET pin. To control leakage, connect a bare copper trace (a trace | 5 |
CAD (KiCad official)
- Symbol:
LTC6906CS6#TRPBF - Footprint:
Package_TO_SOT_SMD:TSOT-23-6 - 3D model: TSOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
ltc6906cs6-trpbf-etched.step/ltc6906cs6-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc6906cs6-trpbf.step/ltc6906cs6-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (14 pp, sha256
d1e1306fa93b14c0, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LTC6906CS6#TRPBF
**Analog Devices** · Timers / Clock Oscillators · TSOT-23-6
LTC6906CS6#TRPBF from Analog Devices, in a TSOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT | output | Oscillator output that swings from GND to V+ through an output resistance of approximately 150Ω; keep the load resistance as high as possible and the load capacitance as low as possible for micropower operation. |
| 2 | GND | power_in | Ground reference pin for the device. |
| 3 | DIV | input | Three-level divider select input: tie to GND for ÷1, leave floating for ÷3, or tie to V+ for ÷10; when floating it is pulled to mid-supply through 2.5MΩ and should be shielded from OUT coupling. |
| 4 | SET | passive | Frequency-setting resistor input: connect RSET (100kΩ to 1MΩ) from this pin to GND, keep capacitance in parallel with RSET below 10pF, and note the SET voltage is approximately 650mV, decreasing about 2.2mV/°C. |
| 5 | GRD | output | Guard signal held within a few millivolts of the SET pin voltage (VGRD relative to VSET limited to ±10mV) to shunt PC board leakage away from SET; route a bare copper trace with no solder mask around SET. |
| 6 | V+ | power_in | Supply voltage input of 2.25V to 3.6V, internally decoupled by a 20Ω resistor in series with an 800pF capacitor, and it should be kept reasonably free of noise and ripple. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSOT-23-6 |
| Category | Clock and Timing |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Frequency Accuracy (LTC6906C), 100kHz ≤ f ≤ 1MHz | Δf | -0.65 | | 0.65 | % | V+ = 2.7V to 3.6V, LTC6906C | 2 |
| Frequency Accuracy (LTC6906C), 100kHz ≤ f ≤ 1MHz | Δf | -0.85 | | 0.85 | % | V+ = 2.25V, LTC6906C | 2 |
| Frequency Accuracy, 100kHz ≤ f ≤ 1MHz | Δf | -0.5 | 0.25 | 0.5 | % | V+ = 2.7V to 3.6V | 2 |
| Frequency Accuracy, 100kHz ≤ f ≤ 1MHz | Δf | -0.7 | 0.25 | 0.7 | % | V+ = 2.25V | 2 |
| Frequency-Setting Resistor Range | RSET | 100 | | 1000 | kΩ | | 3 |
| Frequency Drift Over Temperature | Δf/ΔT | -0.005 | | 0.005 | %/°C | RSET = 316k | 3 |
| Frequency Drift Over Supply | Δf/ΔV | | | 0.06 | %/V | V+ = 2.25V to 3.6V, 100k ≤ RSET ≤ 1000k | 3 |
| Timing Jitter | | | | 0.03 | % | Pin 3 = V+, 100k ≤ RSET ≤ 1000k | 3 |
| Timing Jitter | | | | 0.07 | % | Pin 3 = Open, 100k ≤ RSET ≤ 1000k | 3 |
| Timing Jitter | | | | 0.15 | % | Pin 3 = 0V, 100k ≤ RSET ≤ 1000k | 3 |
| Long-Term Stability of Output Frequency | Sf | | | 300 | ppm/√kHr | Pin 3 = V+ | 3 |
| DC Duty Cycle | | 45 | 50 | 55 | % | | 3 |
| V+ Operating Supply Range | V+ | 2.25 | | 3.6 | V | | 3 |
| Power Supply Current (DIV=1, fOUT=100kHz) | IS | | 12.5 | 18 | μA | RSET = 1000k, Pin 3 = 0V, RL = 10M, V+ = 3.6V | 3 |
| Power Supply Current (DIV=1, fOUT=100kHz) | IS | | 10 | 15 | μA | RSET = 1000k, Pin 3 = 0V, RL = 10M, V+ = 2.25V | 3 |
| Power Supply Current (DIV=1, fOUT=1MHz) | IS | | 78 | 100 | μA | RSET = 100k, Pin 3 = 0V, RL = 10M, V+ = 3.6V | 3 |
| Power Supply Current (DIV=1, fOUT=1MHz) | IS | | 60 | 80 | μA | RSET = 100k, Pin 3 = 0V, RL = 10M, V+ = 2.25V | 3 |
| High Level DIV Input Voltage | VIH | 3.1 | | | V | V+ = 3.6V | 3 |
| High Level DIV Input Voltage | VIH | 2.05 | | | V | V+ = 2.25V | 3 |
| Low Level DIV Input Voltage | VIL | | | 0.5 | V | V+ = 3.6V | 3 |
| Low Level DIV Input Voltage | VIL | | | 0.2 | V | V+ = 2.25V | 3 |
| DIV Input Current | IDIV | -2 | | -1 | μA | Pin 3 = V+ | 3 |
| DIV Input Current | IDIV | 1 | | 2 | μA | Pin 3 = 0V | 3 |
| High Level Output Voltage | VOH | 3.4 | 3.59 | | V | V+ = 3.6V, IOH = -100μA | 3 |
| High Level Output Voltage | VOH | 2.8 | 3.3 | | V | V+ = 3.6V, IOH = -1mA | 3 |
| High Level Output Voltage | VOH | 2.15 | 2.2 | | V | V+ = 2.25V, IOH = -100μA | 3 |
| High Level Output Voltage | VOH | 1.75 | 2 | | V | V+ = 2.25V, IOH = -1mA | 3 |
| Low Level Output Voltage | VOL | | 0.02 | 0.2 | V | V+ = 3.6V, IOL = 100μA | 3 |
| Low Level Output Voltage | VOL | | 0.15 | 0.8 | V | V+ = 3.6V, IOL = 1mA | 3 |
| Low Level Output Voltage | VOL | | 0.03 | 0.1 | V | V+ = 2.25V, IOL = 100μA | 3 |
| Low Level Output Voltage | VOL | | 0.3 | 0.5 | V | V+ = 2.25V, IOL = 1mA | 3 |
| OUT Rise Time | tr | | | 10 | ns | V+ = 3.6V | 3 |
| OUT Rise Time | tr | | | 25 | ns | V+ = 2.25V | 3 |
| OUT Fall Time | tf | | | 10 | ns | V+ = 3.6V | 3 |
| OUT Fall Time | tf | | | 25 | ns | V+ = 2.25V | 3 |
| GRD Pin Voltage Relative to SET Pin Voltage | VGS | -10 | | 10 | mV | -10μA ≤ IGRD ≤ 0.3μA | 3 |
| V+ Absolute Maximum Supply Voltage | V+ | -0.3 | | 6 | V | | 2 |
| DIV to GND Voltage | DIV | -0.3 | | | V | Max is V+ + 0.3V | 2 |
| SET to GND Voltage | SET | -0.3 | | | V | Max is V+ + 0.3V | 2 |
| GRD to GND Voltage | GRD | -0.3 | | | V | Max is V+ + 0.3V | 2 |
| Operating Temperature Range (LTC6906C) | TA | -40 | | 85 | °C | | 2 |
| Specified Temperature Range (LTC6906C) | TA | 0 | | 70 | °C | Guaranteed performance range | 2 |
| Storage Temperature Range | TSTG | -65 | | 150 | °C | | 2 |
| Lead Temperature (Soldering) | | | | 300 | °C | 10 sec | 2 |
| Maximum Junction Temperature | TJMAX | | | 150 | °C | | 2 |
| Thermal Resistance, Junction to Ambient | θJA | | 230 | | °C/W | S6 package | 2 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | SET pin and shunts leakage current away from the SET pin. To control leakage, connect a bare copper trace (a trace | 5 |
## CAD (KiCad official)
- Symbol: `LTC6906CS6#TRPBF`
- Footprint: `Package_TO_SOT_SMD:TSOT-23-6`
- 3D model: TSOT-23-6 (KiCad packages3D, STEP)
- 3D model files: `ltc6906cs6-trpbf-etched.step` / `ltc6906cs6-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ltc6906cs6-trpbf.step` / `ltc6906cs6-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/6906fc.pdf) (14 pp, sha256 `d1e1306fa93b14c0`, retrieved 2026-10-29, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ltc6906cs6-trpbf-datasheet.pdf)