# LTC4415IDHC#TRPBF

**Analog Devices** · Pre-ordered Chips · DFN-16-EP(3x5)

LTC4415IDHC#TRPBF from Analog Devices, in a DFN-16-EP(3x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

## Pinout

| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN1 | power_in | Diode 1 anode and positive power supply for the LTC4415; bypass with a ceramic capacitor of at least 4.7µF, and it can be grounded when not used. |
| 2 | IN1 | power_in | Diode 1 anode and positive power supply (fused to pin 1 on the package); bypass with a ceramic capacitor of at least 4.7µF, and it can be grounded when not used. |
| 3 | EN1 | input | Enable input for Diode 1; a signal above VENTH (800mV typical) enables Diode 1, and it disables below 745mV typical. |
| 4 | CLIM1 | passive | Current limit adjust and monitor for Diode 1; a resistor to ground sets the limit (RCLIM allowed 125Ω to 1000Ω), shorting to ground selects a fixed 6A internal limit, it must not be left open, and stray capacitance should generally be under 200pF. |
| 5 | CLIM2 | passive | Current limit adjust and monitor for Diode 2; a resistor to ground sets the limit (RCLIM allowed 125Ω to 1000Ω), shorting to ground selects a fixed 6A internal limit, it must not be left open, and stray capacitance should generally be under 200pF. |
| 6 | EN2 | input | Enable input for Diode 2 with opposite polarity; a signal below VENTH (800mV typical) enables Diode 2. |
| 7 | IN2 | power_in | Diode 2 anode and positive power supply for the LTC4415; bypass with a ceramic capacitor of at least 4.7µF, and it can be grounded when not used. |
| 8 | IN2 | power_in | Diode 2 anode and positive power supply (fused to pin 7 on the package); bypass with a ceramic capacitor of at least 4.7µF, and it can be grounded when not used. |
| 9 | OUT2 | power_out | Diode 2 cathode and output of the LTC4415; bypass with a ceramic capacitor of at least 4.7µF, and leave open when not used. |
| 10 | OUT2 | power_out | Diode 2 cathode and output (fused to pin 9 on the package); bypass with a ceramic capacitor of at least 4.7µF, and leave open when not used. |
| 11 | STAT2 | output | Open-drain status output for Diode 2 that pulls down during forward diode conduction; it can be left open or grounded when not used. |
| 12 | WARN2 | output | Open-drain overcurrent and thermal warning output for Diode 2 that pulls down when diode 2 current exceeds its current limit or die temperature is close to thermal shutdown. |
| 13 | WARN1 | output | Open-drain overcurrent and thermal warning output for Diode 1 that pulls down when diode 1 current exceeds its current limit or die temperature is close to thermal shutdown. |
| 14 | STAT1 | output | Open-drain status output for Diode 1 that pulls down during forward diode conduction; it can be left open or grounded when not used. |
| 15 | OUT1 | power_out | Diode 1 cathode and output of the LTC4415; bypass with a ceramic capacitor of at least 4.7µF, and leave open when not used. |
| 16 | OUT1 | power_out | Diode 1 cathode and output (fused to pin 15 on the package); bypass with a ceramic capacitor of at least 4.7µF, and leave open when not used. |
| 17 | GND | power_in | Exposed pad; device ground that must be soldered to PCB ground for both electrical connection and thermal conductivity. |

## Key specifications

| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-16-EP(3x5) |
| Category | Interface ICs |
| Pins | 17 |

## Electrical characteristics

Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).

| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Supply Range | VIN1, VOUT1, VIN2, VOUT2 | 1.7 |  | 5.5 | V | At Least One Input/Output Must Be in This Range | 3 |
| Undervoltage Lockout (VINx Rising) | VUVLO | 1.63 |  | 1.7 | V | VINx Rising | 3 |
| Quiescent Current In Forward Regulation | IQF |  | 44 | 80 | µA | VIN1 = VEN1 = VEN2 = 3.6V, IOUT1 = -1mA, VIN2 = VOUT2 = 0V, Measured Through GND Pin | 3 |
| Quiescent Current In Shutdown | IQOFF |  | 13 | 28 | µA | VIN1 = VIN2 = VEN2 = 3.6V, VEN1 = 0V, VOUT1 = VOUT2 = 0V, Measured Through GND Pin | 3 |
| Reverse Turn-Off Current: OUT1 | IQR(OUT) |  | 18 | 40 | µA | VIN1 = 3.6V, VOUT1 = 3.7V, VIN2 = 3.5V, VOUT2 = 3.6V (VOUT1 > VOUT2) | 3 |
| Reverse Turn-Off Current: OUT2 | IQR(OUT) |  | 5 | 11 | µA | VIN1 = 3.6V, VOUT1 = 3.7V, VIN2 = 3.5V, VOUT2 = 3.6V (VOUT1 > VOUT2) | 3 |
| INx Pin Current In Reverse Turn-Off | IQR(IN) |  | 4 | 10 | µA | VOUT1 = VOUT2 = 5.5V | 3 |
| INx Pin Leakage Current | ILEAK(IN) | -1 |  | 1 | µA | VIN1 = VIN2 = 0V, VOUT1 = VOUT2 = 5.5V | 3 |
| Forward Regulation Voltage (VINx, VOUTx) | VFR | 5 | 15 | 25 | mV | IOUTx = -1mA | 3 |
| Reverse Turn-Off Voltage (VINx, VOUTx) | VRTO | -50 | -30 | -10 | mV |  | 3 |
| Forward Dynamic Resistance in Regulation | RFR |  | 18 | 30 | mΩ | IOUTx = -100mA to -300mA | 3 |
| On-Resistance in Constant Resistance Mode | RON |  | 50 | 70 | mΩ | IOUTx = -1A | 3 |
| Current Monitor Ratio at IOUTx = -4A | ICLIMx /IOUTx | 0.9 | 1 | 1.1 | mA/A | When IOUTx = -4A | 3 |
| Current Monitor Ratio at IOUTx = -2A | ICLIMx /IOUTx | 0.8 | 1 | 1.2 | mA/A | When IOUTx = -2A | 3 |
| Current Limit Adjustability | ILIM(ADJ) | 0.5 |  | 4 | A |  | 3 |
| Accuracy of Adjustable Current Limit Threshold (4A) |  | -8 |  | 8 | % | VOUTx = VINx, 0.5V, Current Limit = 4A | 3 |
| Accuracy of Adjustable Current Limit Threshold (2A) |  | -15 |  | 15 | % | VOUTx = VINx, 0.5V, Current Limit = 2A | 3 |
| Internal Current Limit | ILIM(INT) | 4 | 6 | 9 | A | RCLIMx = 0Ω, VOUTx = 0V | 3 |
| EN1 Rising and EN2 Falling Thresholds | VENTH | 760 | 800 | 840 | mV |  | 4 |
| Enable Pin Current When Pulled High |  |  | 0 | 1 | µA | VEN1 = VEN2 = 3.6V | 4 |
| Open-Drain Output Low Voltage | VOL |  | 0.05 | 0.4 | V | Current Into Open-Drain Output = 3mA | 3 |
| Open-Drain Output High Leakage Current |  |  | 0 | 1 | µA | Open-Drain Output Voltage = 5.5V | 3 |
| Current Limit Resistor RCLIM Range | RCLIM | 125 |  | 1000 | Ω | Unless CLIM1/CLIM2 shorted to GND | 9 |
| IN1, IN2, OUT1, OUT2, CLIM1, CLIM2, STAT1, STAT2, WARN1, WARN2 Voltage |  | -0.3 |  | 6 | V |  | 2 |
| EN1, EN2 Voltage |  | -0.3 |  |  | V | Upper limit is Max(VINx, VOUTx) | 2 |
| Operating Junction Temperature Range | TJ | -40 |  | 125 | °C | Notes 3, 4 | 2 |
| Storage Temperature Range | TSTG | -65 |  | 150 | °C |  | 2 |
| Thermal Resistance Junction-to-Ambient (DFN) | θJA |  | 43 |  | °C/W | Correctly soldered to 2500mm² double-sided 1oz copper board; approximately | 12 |

## CAD (KiCad official)

- Symbol: `LTC4415IDHC#TRPBF`
- Footprint: `Package_DFN_QFN:DFN-16-1EP_3x5mm_P0.5mm_EP1.66x4.4mm`
- 3D model: DFN-16-EP(3x5) (KiCad packages3D, STEP)
- 3D model files: `ltc4415idhc-trpbf-etched.step` / `ltc4415idhc-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ltc4415idhc-trpbf.step` / `ltc4415idhc-trpbf.glb` are the bare package body.

## Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/4415fa.pdf) (20 pp, sha256 `e35970b1d556a4ba`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).

[Datasheet PDF](docs/ltc4415idhc-trpbf-datasheet.pdf)