component
LTC4210-1IS6#TRPBF
Public Made by Adomby adom
Analog Devices Monitors & Reset Circuits, TSOT-23-6. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
LTC4210-1IS6#TRPBF
Analog Devices · Monitors & Reset Circuits · TSOT-23-6
LTC4210-1IS6#TRPBF from Analog Devices, in a TSOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TIMER | input | Timer input pin where an external capacitor CTIMER sets a 272.9ms/µF initial timing delay and a 21.7ms/µF circuit breaker delay, and the GATE turns off whenever TIMER is pulled beyond the COMP2 threshold, such as for overvoltage detection with an external Zener. |
| 2 | GND | power_in | Ground pin for the device. |
| 3 | ON | input | ON input has a low-to-high threshold of 1.3V with 80mV hysteresis and a glitch filter, where a low level resets the LTC4210 and GATE turns on after the initial timing cycle when ON goes high. |
| 4 | GATE | output | High side gate drive for an external N-channel MOSFET, with an internal charge pump providing a 10µA pull-up current and Zener clamps to VCC and ground, and an external R-C compensation network required for current limit loop stability. |
| 5 | SENSE | input | Current limit sense input where a sense resistor between VCC and SENSE sets the analog current limit by holding SENSE 50mV below VCC in overload, and connecting SENSE to VCC disables the current limit loop and circuit breaker mode. |
| 6 | VCC | power_in | Positive supply input with an operating range of 2.7V to 16.5V, where an undervoltage lockout circuit with a glitch filter resets the LTC4210 when a low supply voltage is detected. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSOT-23-6 |
| Category | Power Management ICs |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC Supply Voltage | VCC | 2.7 | 16.5 | V | 3 | ||
| VCC Supply Current | ICC | 0.65 | 3.5 | mA | 3 | ||
| VCC Undervoltage Lockout Release | VLKOR | 2.2 | 2.5 | 2.65 | V | VCC Rising | 3 |
| ON Pin Input Current | IINON | -10 | 0 | 10 | µA | 3 | |
| SENSE Pin Input Current | IINSENSE | -10 | 5 | 10 | µA | VSENSE = VCC | 3 |
| Circuit Breaker Trip Voltage | VCB | 44 | 50 | 56 | mV | VCB = (VCC, VSENSE) | 3 |
| GATE Pin Pull-Up Current | IGATEUP | -5 | -10 | -15 | µA | VGATE = 0V | 3 |
| GATE Pin Pull-Down Current | IGATEDN | 25 | mA | VTIMER = 1.5V, VGATE = 3V or VON = 0V, VGATE = 3V or VCC, VSENSE = 100mV, VGATE = 3V | 3 | ||
| External N-Channel Gate Drive (VGATE, VCC) | ∆VGATE | 4 | 6.5 | 8 | V | VCC = 2.7V | 3 |
| External N-Channel Gate Drive (VGATE, VCC) | ∆VGATE | 4.5 | 7.5 | 10 | V | VCC = 3V | 3 |
| External N-Channel Gate Drive (VGATE, VCC) | ∆VGATE | 5 | 8.5 | 12 | V | VCC = 3.3V | 3 |
| External N-Channel Gate Drive (VGATE, VCC) | ∆VGATE | 10 | 12 | 16 | V | VCC = 5V | 3 |
| External N-Channel Gate Drive (VGATE, VCC) | ∆VGATE | 9 | 12 | 16 | V | VCC = 12V | 3 |
| External N-Channel Gate Drive (VGATE, VCC) | ∆VGATE | 6 | 11 | 18 | V | VCC = 15V | 3 |
| TIMER Pin Pull-Up Current (Initial Cycle) | ITIMERUP | -2 | -5 | -8.5 | µA | Initial Cycle, VTIMER = 1V | 3 |
| TIMER Pin Pull-Up Current (During Current Fault) | ITIMERUP | -25 | -60 | -100 | µA | During Current Fault Condition, VTIMER = 1V | 3 |
| TIMER Pin Pull-Down Current (After Current Fault Disappears) | ITIMERDN | 2 | 3.5 | µA | After Current Fault Disappears, VTIMER = 1V | 3 | |
| TIMER Pin Pull-Down Current (Under Normal Conditions) | ITIMERDN | 100 | µA | Under Normal Conditions, VTIMER = 1V | 3 | ||
| TIMER Pin Threshold High | VTIMER | 1.22 | 1.3 | 1.38 | V | TIMER Rising | 3 |
| TIMER Pin Threshold Low | VTIMER | 0.15 | 0.2 | 0.25 | V | TIMER Falling | 3 |
| ON Pin Threshold | VON | 1.22 | 1.3 | 1.38 | V | ON Rising | 3 |
| Turn-Off Time (TIMER Rise to GATE Fall) | tOFF(TMRHIGH) | 1 | µs | VTIMER = 0V to 2V Step, VCC = VON = 5V | 3 | ||
| Turn-Off Time (ON Fall to GATE Fall) | tOFF(ONLOW) | 30 | µs | VON = 5V to 0V Step, VCC = 5V | 3 | ||
| Turn-Off Time (VCC Fall to IC Reset) | tOFF(VCCLOW) | 30 | µs | VCC = 5V to 2V Step, VON = 5V | 3 | ||
| Supply Voltage (VCC) Absolute Maximum | VCC | 17 | V | 2 | |||
| Input Voltage (SENSE, TIMER) Absolute Maximum | -0.3 | V | Upper limit printed as (VCC + 0.3V) | 2 | |||
| Input Voltage (ON) Absolute Maximum | -0.3 | 17 | V | 2 | |||
| Operating Temperature Range (LTC4210-1I) | -40 | 85 | °C | LTC4210-1I | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Maximum Junction Temperature | TJMAX | 125 | °C | 2 | |||
| Thermal Resistance, Junction to Ambient | θJA | 230 | °C/W | S6 package (6-lead plastic TSOT-23) | 2 |
CAD (KiCad official)
- Symbol:
LTC4210-1IS6#TRPBF - Footprint:
Package_TO_SOT_SMD:TSOT-23-6 - 3D model: TSOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
ltc4210-1is6-trpbf-etched.step/ltc4210-1is6-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc4210-1is6-trpbf.step/ltc4210-1is6-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (22 pp, sha256
ceb3dc548f64f00a, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LTC4210-1IS6#TRPBF
**Analog Devices** · Monitors & Reset Circuits · TSOT-23-6
LTC4210-1IS6#TRPBF from Analog Devices, in a TSOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TIMER | input | Timer input pin where an external capacitor CTIMER sets a 272.9ms/µF initial timing delay and a 21.7ms/µF circuit breaker delay, and the GATE turns off whenever TIMER is pulled beyond the COMP2 threshold, such as for overvoltage detection with an external Zener. |
| 2 | GND | power_in | Ground pin for the device. |
| 3 | ON | input | ON input has a low-to-high threshold of 1.3V with 80mV hysteresis and a glitch filter, where a low level resets the LTC4210 and GATE turns on after the initial timing cycle when ON goes high. |
| 4 | GATE | output | High side gate drive for an external N-channel MOSFET, with an internal charge pump providing a 10µA pull-up current and Zener clamps to VCC and ground, and an external R-C compensation network required for current limit loop stability. |
| 5 | SENSE | input | Current limit sense input where a sense resistor between VCC and SENSE sets the analog current limit by holding SENSE 50mV below VCC in overload, and connecting SENSE to VCC disables the current limit loop and circuit breaker mode. |
| 6 | VCC | power_in | Positive supply input with an operating range of 2.7V to 16.5V, where an undervoltage lockout circuit with a glitch filter resets the LTC4210 when a low supply voltage is detected. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSOT-23-6 |
| Category | Power Management ICs |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC Supply Voltage | VCC | 2.7 | | 16.5 | V | | 3 |
| VCC Supply Current | ICC | | 0.65 | 3.5 | mA | | 3 |
| VCC Undervoltage Lockout Release | VLKOR | 2.2 | 2.5 | 2.65 | V | VCC Rising | 3 |
| ON Pin Input Current | IINON | -10 | 0 | 10 | µA | | 3 |
| SENSE Pin Input Current | IINSENSE | -10 | 5 | 10 | µA | VSENSE = VCC | 3 |
| Circuit Breaker Trip Voltage | VCB | 44 | 50 | 56 | mV | VCB = (VCC, VSENSE) | 3 |
| GATE Pin Pull-Up Current | IGATEUP | -5 | -10 | -15 | µA | VGATE = 0V | 3 |
| GATE Pin Pull-Down Current | IGATEDN | 25 | | | mA | VTIMER = 1.5V, VGATE = 3V or VON = 0V, VGATE = 3V or VCC, VSENSE = 100mV, VGATE = 3V | 3 |
| External N-Channel Gate Drive (VGATE, VCC) | ∆VGATE | 4 | 6.5 | 8 | V | VCC = 2.7V | 3 |
| External N-Channel Gate Drive (VGATE, VCC) | ∆VGATE | 4.5 | 7.5 | 10 | V | VCC = 3V | 3 |
| External N-Channel Gate Drive (VGATE, VCC) | ∆VGATE | 5 | 8.5 | 12 | V | VCC = 3.3V | 3 |
| External N-Channel Gate Drive (VGATE, VCC) | ∆VGATE | 10 | 12 | 16 | V | VCC = 5V | 3 |
| External N-Channel Gate Drive (VGATE, VCC) | ∆VGATE | 9 | 12 | 16 | V | VCC = 12V | 3 |
| External N-Channel Gate Drive (VGATE, VCC) | ∆VGATE | 6 | 11 | 18 | V | VCC = 15V | 3 |
| TIMER Pin Pull-Up Current (Initial Cycle) | ITIMERUP | -2 | -5 | -8.5 | µA | Initial Cycle, VTIMER = 1V | 3 |
| TIMER Pin Pull-Up Current (During Current Fault) | ITIMERUP | -25 | -60 | -100 | µA | During Current Fault Condition, VTIMER = 1V | 3 |
| TIMER Pin Pull-Down Current (After Current Fault Disappears) | ITIMERDN | 2 | 3.5 | | µA | After Current Fault Disappears, VTIMER = 1V | 3 |
| TIMER Pin Pull-Down Current (Under Normal Conditions) | ITIMERDN | 100 | | | µA | Under Normal Conditions, VTIMER = 1V | 3 |
| TIMER Pin Threshold High | VTIMER | 1.22 | 1.3 | 1.38 | V | TIMER Rising | 3 |
| TIMER Pin Threshold Low | VTIMER | 0.15 | 0.2 | 0.25 | V | TIMER Falling | 3 |
| ON Pin Threshold | VON | 1.22 | 1.3 | 1.38 | V | ON Rising | 3 |
| Turn-Off Time (TIMER Rise to GATE Fall) | tOFF(TMRHIGH) | | | 1 | µs | VTIMER = 0V to 2V Step, VCC = VON = 5V | 3 |
| Turn-Off Time (ON Fall to GATE Fall) | tOFF(ONLOW) | | | 30 | µs | VON = 5V to 0V Step, VCC = 5V | 3 |
| Turn-Off Time (VCC Fall to IC Reset) | tOFF(VCCLOW) | | | 30 | µs | VCC = 5V to 2V Step, VON = 5V | 3 |
| Supply Voltage (VCC) Absolute Maximum | VCC | | | 17 | V | | 2 |
| Input Voltage (SENSE, TIMER) Absolute Maximum | | -0.3 | | | V | Upper limit printed as (VCC + 0.3V) | 2 |
| Input Voltage (ON) Absolute Maximum | | -0.3 | | 17 | V | | 2 |
| Operating Temperature Range (LTC4210-1I) | | -40 | | 85 | °C | LTC4210-1I | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| Maximum Junction Temperature | TJMAX | | | 125 | °C | | 2 |
| Thermal Resistance, Junction to Ambient | θJA | | 230 | | °C/W | S6 package (6-lead plastic TSOT-23) | 2 |
## CAD (KiCad official)
- Symbol: `LTC4210-1IS6#TRPBF`
- Footprint: `Package_TO_SOT_SMD:TSOT-23-6`
- 3D model: TSOT-23-6 (KiCad packages3D, STEP)
- 3D model files: `ltc4210-1is6-trpbf-etched.step` / `ltc4210-1is6-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ltc4210-1is6-trpbf.step` / `ltc4210-1is6-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/421012fa.pdf) (22 pp, sha256 `ceb3dc548f64f00a`, retrieved 2026-10-29, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ltc4210-1is6-trpbf-datasheet.pdf)