3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLTC4063EDD#PBF
Analog Devices · Battery Management ICs · DFN-10-EP(3x3)
LTC4063EDD#PBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BAT | bidirectional | Charger output and LDO regulator input that charges the battery and regulates the final float voltage to 4.2V, also supplying power to the LDO. |
| 2 | OUT | power_out | LDO regulator output that should be bypassed with a ≥2µF low ESR capacitor as close to the pin as possible, with a minimum VOUT of 1.2V. |
| 3 | FB | input | LDO feedback input compared to the internal 800mV reference by the error amplifier, with an external resistor divider between OUT and FB setting the output voltage. |
| 4 | LDOEN | input | LDO enable input where a logic high shuts down the LDO (OUT becomes high impedance, battery drain under 5µA) and a logic low enables it, with a 2MΩ pull-down defaulting the LDO to enabled. |
| 5 | CHGEN | input | Charger enable input where a logic high puts the charger into shutdown with ICC below 65µA and a logic low enables charging, with a 2MΩ pull-down defaulting the charger to enabled. |
| 6 | CHRG | output | Open-drain charge status output whose NMOS can sink 10mA in the pull-down state, usable as a logic interface or LED driver, and high impedance depending on IDETECT and the termination method. |
| 7 | TIMER | input | Timer program and termination select pin, where a capacitor to ground selects charge time termination (t = 3 hours per 0.1µF), ground selects current termination, and VCC selects user termination. |
| 8 | IDET | passive | Charge current detection threshold program pin set by a resistor RDET to ground, clamped to approximately 2.4V, and driving it beyond the clamp voltage should be avoided. |
| 9 | PROG | passive | Charge current program and monitor pin set by a resistor RPROG to ground, servoing to 1V in constant-current mode and used to measure charge current. |
| 10 | VCC | power_in | Positive input supply for the battery charger, operating from 4.3V to 8V and to be bypassed with a 1µF capacitor. |
| 11 | GND | power_in | Ground connected to the exposed pad on the package underside, which must be soldered to the PCB copper for minimal thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VCC Supply Voltage | VCC | 4.3 | 8 | V | 2 | ||
| ICC Supply Current, Charge Mode | ICC | 400 | 800 | µA | Charge Mode (Note 4), RPROG = 10k | 2 | |
| ICC Supply Current, Standby Mode | ICC | 100 | 200 | µA | Standby Mode, Charge Terminated | 2 | |
| ICC Supply Current, Shutdown | ICC | 35 | 65 | µA | Shutdown (CHGEN = 5V, VCC < VBAT or VCC < VUV) | 2 | |
| ICC Supply Current, CHGEN and LDOEN high | ICC | 15 | 30 | µA | CHGEN = 5V and LDOEN = 5V | 2 | |
| VBAT Regulated Output (Float) Voltage | VFLOAT | 4.185 | 4.2 | 4.215 | V | 0°C ≤ TA ≤ 85°C | 2 |
| VBAT Regulated Output (Float) Voltage, second printed row | VFLOAT | 4.17 | 4.2 | 4.23 | V | 2 | |
| BAT Pin Current, constant-current mode | IBAT | 93 | 100 | 107 | mA | RPROG = 10k, Constant-Current Mode | 2 |
| BAT Pin Current, constant-current mode | IBAT | 760 | 800 | 840 | mA | RPROG = 1.25k, Constant-Current Mode | 2 |
| BAT Pin Current, Standby Mode | IBAT | -1 | -3.5 | 1 | µA | Standby Mode, Charge Terminated | 2 |
| BAT Pin Current, Shutdown Mode | IBAT | -2 | -7 | 2 | µA | Shutdown Mode (CHGEN = 5V, LDOEN = 5V) | 2 |
| PROG Pin Voltage | VPROG | 0.97 | 1 | 1.03 | V | RPROG = 10k, Constant-Current Mode | 2 |
| CHRG Output Low Voltage | VCHRG | 0.35 | 0.6 | V | ICHRG = 5mA | 2 | |
| Trickle Charge Current | ITRIKL | 6 | 10 | 14 | mA | VBAT < VTRIKL, RPROG = 10k | 2 |
| Trickle Charge Current | ITRIKL | 60 | 80 | 100 | mA | VBAT < VTRIKL, RPROG = 1.25k | 2 |
| Trickle Charge Threshold Voltage | VTRIKL | 2.8 | 2.9 | 3 | V | VBAT Rising | 2 |
| VCC Undervoltage Lockout Voltage | VUV | 3.7 | 3.8 | 3.9 | V | From Low to High | 2 |
| VCC, VBAT Lockout Threshold Voltage | VASD | 145 | 180 | 220 | mV | VCC from Low to High, VBAT = 4.2V | 2 |
| VCC, VBAT Lockout Threshold Voltage | VASD | 10 | 45 | 75 | mV | VCC from High to Low, VBAT = 4.2V | 2 |
| CHGEN Input Threshold Voltage | VCHGEN | 0.4 | 0.7 | 1 | V | CHGEN Rising, 4.3V < VCC < 8V | 2 |
| CHGEN Pin Pull-Down Resistor | RCHGEN | 1.2 | 2 | 5 | MΩ | 3 | |
| Charge Termination Mode Threshold Voltage | VCT | 0.4 | 0.7 | 1 | V | VTIMER from High to Low | 3 |
| User Termination Mode Threshold Voltage | VUT | 4.1 | 4.15 | 4.5 | V | VTIMER from Low to High | 3 |
| Charge Current Detection Threshold | IDETECT | 90 | 100 | 110 | mA | RDET = 1k, 0°C ≤ TA ≤ 85°C | 3 |
| Charge Current Detection Threshold | IDETECT | 45 | 50 | 55 | mA | RDET = 2k, 0°C ≤ TA ≤ 85°C | 3 |
| Charge Current Detection Threshold | IDETECT | 8.5 | 10 | 11.5 | mA | RDET = 10k, 0°C ≤ TA ≤ 85°C | 3 |
| Charge Current Detection Threshold | IDETECT | 4 | 5 | 6 | mA | RDET = 20k, 0°C ≤ TA ≤ 85°C | 3 |
| Recharge Threshold Voltage | ΔVRECHRG | 75 | 100 | 125 | mV | VFLOAT, VRECHRG, 0°C ≤ TA ≤ 85°C | 3 |
| Termination Comparator Filter Time | tTERM | 1 | 1.5 | 2.2 | ms | Current Termination Mode | 3 |
| Recharge Comparator Filter Time | tRECHRG | 3 | 7 | 14 | ms | 3 | |
| Charge Cycle Time | tTIMER | 2.55 | 3 | 3.45 | Hour | CTIMER = 0.1µF | 3 |
| LDO Supply Voltage (BAT) | VBAT-LDO | 2.65 | 4.4 | V | 3 | ||
| LDO Supply Current (from BAT) | IBAT-LDO | 15 | 25 | µA | VCC < VBAT, IOUT = 0mA | 3 | |
| LDO Supply Current (from BAT) | IBAT-LDO | 9 | 18 | µA | VCC > VBAT, IOUT = 0mA (Note 6) | 3 | |
| LDO Supply Current in Shutdown | IBAT-LDO-SD | 2.5 | 5 | µA | VBAT = 4.4V | 3 | |
| FB Regulated Voltage | VFB | 784 | 800 | 816 | mV | VBAT = 3.7V, IOUT = 1mA | 3 |
| VFB Line Regulation | VFB(LINE) | 1 | 4 | mV | VBAT = 2.65V to 4.4V, IOUT = 1mA | 3 | |
| VFB Load Regulation | VFB(LOAD) | 1 | 4 | mV | IOUT = 1mA to 100mA, VBAT = 4.4V | 3 | |
| LDOEN Input Threshold Voltage (Rising) | VLDOEN | 0.4 | 0.7 | 1 | V | LDOEN Rising, VBAT = 4.4V | 3 |
| LDOEN Pin Pull-Down Resistor | RLDOEN | 1.2 | 2 | 5 | MΩ | 3 | |
| LDO Dropout Voltage | VDO | 125 | 200 | mV | IOUT = 100mA, VOUT = 3V | 3 | |
| LDO Undervoltage Lockout Threshold | VLDOUVLO | 2.45 | 2.55 | 2.65 | V | VBAT from High to Low | 3 |
| FB Pin Current | IFB | -25 | 0 | 25 | nA | 3 | |
| Supply Voltage (VCC) absolute maximum | VCC | -0.3 | 10 | V | Input Supply Voltage (VCC) | 2 | |
| CHGEN, LDOEN, CHRG absolute maximum | -0.3 | 10 | V | 2 | |||
| FB absolute maximum | -0.3 | 8 | V | 2 | |||
| PROG, IDET, TIMER absolute maximum | -0.3 | V | Max printed as VCC + 0.3V | 2 | |||
| BAT, OUT absolute maximum | -0.3 | 8 | V | 2 | |||
| BAT Pin Current | 1 | A | Note 8: long term current density limitations | 2 | |||
| Maximum Junction Temperature | TJMAX | 125 | °C | Note 7 | 2 | ||
| Operating Temperature Range | -40 | 85 | °C | Note 2: guaranteed 0°C to 70°C, specified -40°C to 85°C | 2 | ||
| Storage Temperature Range | -65 | 125 | °C | 2 | |||
| Thermal Resistance, junction to ambient | θJA | 40 | °C/W | Note 3: exposed pad soldered to PC board | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | thermal contact between the exposed pad on the backside of the package and the copper board will result in thermal | 16 |
CAD (KiCad official)
- Symbol:
LTC4063EDD#PBF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
ltc4063edd-pbf-etched.step/ltc4063edd-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc4063edd-pbf.step/ltc4063edd-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
db90277b2ea91239, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).