main
Ray
Publish 0.1.0
91238f7
LTC3769EUF#PBF
Analog Devices · DC-DC Controllers · QFN-24-EP(4x4)
LTC3769EUF#PBF from Analog Devices, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBIAS | power_in | Main supply pin with an operating voltage range of 4.5V to 60V (65V abs max), normally tied to VIN or the boost output and bypassed to signal ground. |
| 2 | PGOOD | output | Open-drain power good output that is pulled to ground when the output voltage is more than ±10% away from the regulated output, after 45μs outside the range. |
| 3 | ILIM | input | Sets the peak current sense threshold to 50mV, 75mV or 100mV when connected to GND, left floating or connected to INTVCC respectively. |
| 4 | NC | unconnected | No connection; shown as NC in the QFN pin configuration. |
| 5 | INTVCC | power_out | Output of the internal 5.4V LDO that powers control circuits and gate drivers; connect to pin 22 and decouple to GND with at least 4.7μF low ESR ceramic capacitor. |
| 6 | NC | unconnected | No connection; shown as NC in the QFN pin configuration. |
| 7 | FREQ | input | Frequency control pin: GND forces 350kHz, INTVCC forces 535kHz, and a resistor to GND programs 50kHz to 900kHz. |
| 8 | GND | power_in | Ground pin that must be connected, with the exposed pad soldered to the PCB for rated electrical and thermal performance. |
| 9 | PLLIN/MODE | input | External synchronization input and light-load mode select; GND selects Burst Mode operation and INTVCC forces continuous inductor current operation. |
| 10 | GND | power_in | Ground pin that must be connected, with the exposed pad soldered to the PCB for rated electrical and thermal performance. |
| 11 | RUN | input | Run control input: forcing below 1.28V shuts down the controller and forcing below 0.7V shuts down the entire LTC3769 to approximately 4μA quiescent current. |
| 12 | SS | input | Output soft-start input where a capacitor to ground sets the output voltage ramp rate during start-up. |
| 13 | SENSE- | input | Negative current sense comparator input, normally connected to the negative terminal of a current sense resistor in series with the inductor. |
| 14 | SENSE+ | input | Positive current sense comparator input that also powers the current comparator, with a common mode range of 2.3V to 60V (65V abs max). |
| 15 | VFB | input | Error amplifier feedback input receiving the remotely sensed output through an external resistive divider, regulating to a ±1% 1.200V reference. |
| 16 | ITH | passive | Current control threshold and error amplifier compensation point whose voltage sets the current trip threshold. |
| 17 | OVMODE | input | Overvoltage mode select: tying to GND enables overvoltage protection with TG forced on, while tying to INTVCC disables it and sets pulse-skipping when synchronized. |
| 18 | SW | passive | Switch node connected to the synchronous MOSFET source, main MOSFET drain and inductor, rated -5V to 65V absolute maximum. |
| 19 | TG | output | Top gate driver output connected to the gate of the synchronous N-channel MOSFET. |
| 20 | BOOST | passive | Floating power supply for the synchronous N-channel MOSFET, bypassed to SW with a capacitor and supplied through a Schottky diode from INTVCC. |
| 21 | BG | output | Bottom gate driver output connected to the gate of the main N-channel MOSFET. |
| 22 | INTVCC | power_out | Output of the internal 5.4V LDO, connected to pin 5 by a PCB trace and decoupled to GND with at least 4.7μF low ESR ceramic capacitor. |
| 23 | EXTVCC | power_in | External power input to an internal LDO supplying INTVCC when higher than 4.7V; do not float or exceed 14V on this pin. |
| 24 | GND | power_in | Ground pin that must be connected, with the exposed pad soldered to the PCB for rated electrical and thermal performance. |
| 25 | GND | power_in | Exposed pad ground that must be soldered to the PCB for rated electrical and thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-24-EP(4x4) |
| Category | Power Supply Chip |
| Pins | 25 |
CAD (KiCad official)
- Symbol:
LTC3769EUF#PBF - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
ltc3769euf-pbf-etched.step/ltc3769euf-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc3769euf-pbf.step/ltc3769euf-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (32 pp, sha256
05707b908f19ef44, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LTC3769EUF#PBF
**Analog Devices** · DC-DC Controllers · QFN-24-EP(4x4)
LTC3769EUF#PBF from Analog Devices, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VBIAS | power_in | Main supply pin with an operating voltage range of 4.5V to 60V (65V abs max), normally tied to VIN or the boost output and bypassed to signal ground. |
| 2 | PGOOD | output | Open-drain power good output that is pulled to ground when the output voltage is more than ±10% away from the regulated output, after 45μs outside the range. |
| 3 | ILIM | input | Sets the peak current sense threshold to 50mV, 75mV or 100mV when connected to GND, left floating or connected to INTVCC respectively. |
| 4 | NC | unconnected | No connection; shown as NC in the QFN pin configuration. |
| 5 | INTVCC | power_out | Output of the internal 5.4V LDO that powers control circuits and gate drivers; connect to pin 22 and decouple to GND with at least 4.7μF low ESR ceramic capacitor. |
| 6 | NC | unconnected | No connection; shown as NC in the QFN pin configuration. |
| 7 | FREQ | input | Frequency control pin: GND forces 350kHz, INTVCC forces 535kHz, and a resistor to GND programs 50kHz to 900kHz. |
| 8 | GND | power_in | Ground pin that must be connected, with the exposed pad soldered to the PCB for rated electrical and thermal performance. |
| 9 | PLLIN/MODE | input | External synchronization input and light-load mode select; GND selects Burst Mode operation and INTVCC forces continuous inductor current operation. |
| 10 | GND | power_in | Ground pin that must be connected, with the exposed pad soldered to the PCB for rated electrical and thermal performance. |
| 11 | RUN | input | Run control input: forcing below 1.28V shuts down the controller and forcing below 0.7V shuts down the entire LTC3769 to approximately 4μA quiescent current. |
| 12 | SS | input | Output soft-start input where a capacitor to ground sets the output voltage ramp rate during start-up. |
| 13 | SENSE- | input | Negative current sense comparator input, normally connected to the negative terminal of a current sense resistor in series with the inductor. |
| 14 | SENSE+ | input | Positive current sense comparator input that also powers the current comparator, with a common mode range of 2.3V to 60V (65V abs max). |
| 15 | VFB | input | Error amplifier feedback input receiving the remotely sensed output through an external resistive divider, regulating to a ±1% 1.200V reference. |
| 16 | ITH | passive | Current control threshold and error amplifier compensation point whose voltage sets the current trip threshold. |
| 17 | OVMODE | input | Overvoltage mode select: tying to GND enables overvoltage protection with TG forced on, while tying to INTVCC disables it and sets pulse-skipping when synchronized. |
| 18 | SW | passive | Switch node connected to the synchronous MOSFET source, main MOSFET drain and inductor, rated -5V to 65V absolute maximum. |
| 19 | TG | output | Top gate driver output connected to the gate of the synchronous N-channel MOSFET. |
| 20 | BOOST | passive | Floating power supply for the synchronous N-channel MOSFET, bypassed to SW with a capacitor and supplied through a Schottky diode from INTVCC. |
| 21 | BG | output | Bottom gate driver output connected to the gate of the main N-channel MOSFET. |
| 22 | INTVCC | power_out | Output of the internal 5.4V LDO, connected to pin 5 by a PCB trace and decoupled to GND with at least 4.7μF low ESR ceramic capacitor. |
| 23 | EXTVCC | power_in | External power input to an internal LDO supplying INTVCC when higher than 4.7V; do not float or exceed 14V on this pin. |
| 24 | GND | power_in | Ground pin that must be connected, with the exposed pad soldered to the PCB for rated electrical and thermal performance. |
| 25 | GND | power_in | Exposed pad ground that must be soldered to the PCB for rated electrical and thermal performance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-24-EP(4x4) |
| Category | Power Supply Chip |
| Pins | 25 |
## CAD (KiCad official)
- Symbol: `LTC3769EUF#PBF`
- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`
- 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files: `ltc3769euf-pbf-etched.step` / `ltc3769euf-pbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ltc3769euf-pbf.step` / `ltc3769euf-pbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/3769fa.pdf) (32 pp, sha256 `05707b908f19ef44`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ltc3769euf-pbf-datasheet.pdf)