component
LTC3290EMSE#TRPBF
Public Made by Adomby adom
Analog Devices Charge Pumps, MSOP-10-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLTC3290EMSE#TRPBF
Analog Devices · Charge Pumps · MSOP-10-EP
LTC3290EMSE#TRPBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VAUX | power_in | Auxiliary input supply voltage that should be bypassed with a low impedance ceramic capacitor. |
| 2 | EN | input | Enable logic input: a logic high enables the part and regulates the output, and this pin must not be left floating. |
| 3 | C+ | passive | Positive connection of the flying capacitor, a high-frequency switching node that should not be routed near FB or VSET. |
| 4 | C- | passive | Negative connection of the flying capacitor, a high-frequency switching node that should not be routed near FB or VSET. |
| 5 | VIN | power_in | Input supply voltage that should be bypassed with a low impedance ceramic capacitor. |
| 6 | BIAS | power_out | Internal bias voltage of 4.5V (typ) that requires a 4.7µF bypass capacitor to GND and must not be loaded or driven externally. |
| 7 | PGOOD | output | Open-drain power good output that is low when enabled and out of regulation, requires an external pull-up to a voltage ≤ 3.6V. |
| 8 | FB | input | Feedback input that servos to 1V in boost mode via an external divider from VOUT, and sets the tracking reference current in VIN tracking mode. |
| 9 | VSET | input | Output voltage set pin that must be grounded for standard boost operation, or connected through an external resistor to VOUT for VIN tracking mode, and must not be floated. |
| 10 | VOUT | power_out | Output voltage pin that should be bypassed with a low impedance ceramic capacitor to GND (boost mode) or to VIN (tracking mode). |
| 11 | GND | power_in | Exposed pad ground that must be soldered to the PC board ground plane for proper function and rated thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10-EP |
| Category | Power Management (PMIC) |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, EN, VAUX voltage | VIN, EN, VAUX | -60 | 60 | V | 2 | ||
| VIN to VAUX, VIN to EN voltage | VIN to VAUX, VIN to EN | 60 | V | 2 | |||
| VOUT, VSET voltage | VOUT, VSET | -0.3 | 60 | V | 2 | ||
| FB, PGOOD voltage | FB, PGOOD | -0.3 | V | Upper limit printed as BIAS + 0.3V | 2 | ||
| BIAS voltage | BIAS | -0.3 | 6 | V | 2 | ||
| Operating junction temperature range | TJ | -55 | 150 | °C | Notes 2, 3 | 2 | |
| Storage temperature range | -65 | 150 | °C | 2 | |||
| Operating temperature range, LTC3290EMSE#TRPBF | -40 | 125 | °C | Order information temperature range for E grade | 2 | ||
| Guaranteed junction temperature range, LTC3290E | TJ | 0 | 85 | °C | Note 2: LTC3290E guaranteed junction temperature | 3 | |
| Thermal resistance, junction to ambient | θJA | 45 | °C/W | 2 | |||
| Maximum junction temperature | TJMAX | 150 | °C | 2 | |||
| VIN Input Supply Voltage Range | VIN | 4.5 | 55 | V | l: over specified operating junction temperature range | 3 | |
| VAUX Auxiliary Supply Voltage Range | VAUX | 4.5 | 55 | V | l: over specified operating junction temperature range | 3 | |
| Sum of Input Supply Voltages | (VIN + VAUX) | 9 | 55 | V | l: over specified operating junction temperature range | 3 | |
| Input Overvoltage Rising Threshold | (VIN + VAUX)_OV | 63 | 65 | 67 | V | (VIN + VAUX) Rising, VSET = Hig (Note 4) | 3 |
| Output Overvoltage Rising Threshold | VOUT_OV | 63 | 65 | 67 | V | VOUT Rising (Note 4) | 3 |
| VIN Quiescent Current | IVIN | 3 | 5 | µA | Shutdown, EN = 0V | 3 | |
| VIN Quiescent Current | IVIN | 15 | 30 | µA | IVOUT = 0mA | 3 | |
| VAUX Quiescent Current | IVAUX | 1 | 3 | µA | Shutdown, EN = 0V | 3 | |
| FB Regulation Voltage | VFB | 0.98 | 1 | 1.02 | V | l: over specified operating junction temperature range | 3 |
| VOUT Current Limit | ICL_VOUT | 100 | 150 | 200 | mA | VOUT Not in Regulation (Note 5); l: over specified operating junction temperature range | 3 |
| Enable Pin Threshold Rising | VENH | 1.1 | 2 | V | l: over specified operating junction temperature range | 3 | |
| Enable Pin Threshold Falling | VENL | 0.4 | 1 | V | l: over specified operating junction temperature range | 3 | |
| VSET Pin Threshold Rising | VSETH | 1.1 | 2 | V | l: over specified operating junction temperature range | 3 | |
| VSET Pin Threshold Falling | VSETL | 0.4 | 1 | V | l: over specified operating junction temperature range | 3 | |
| Enable Pin Leakage Current | IEN | -1 | 0 | 1 | µA | 3 | |
| PGOOD Pin Threshold Rising in Boost | VPG_RISE_BST | 95 | 98 | % | % of Final Regulation Voltage, VSET = GND; l: over specified operating junction temperature range | 3 | |
| PGOOD Pin Threshold Falling in Boost | VPG_FALL_BST | 88 | 91 | % | % of Final Regulation Voltage, VSET = GND; l: over specified operating junction temperature range | 3 | |
| PGOOD Output High Leakage Current | IPGOOD_HIGH | -1 | 1 | µA | VPGOOD = 3V; l: over specified operating junction temperature range | 3 | |
| PGOOD Output Low Voltage | VPGOOD_LOW | 0.1 | 0.4 | V | IPGOOD = 0.2mA; l: over specified operating junction temperature range | 3 |
CAD (KiCad official)
- Symbol:
LTC3290EMSE#TRPBF - Footprint:
Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm - 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files:
ltc3290emse-trpbf-etched.step/ltc3290emse-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc3290emse-trpbf.step/ltc3290emse-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (14 pp, sha256
7f7000eb19e1a807, retrieved 2026-10-19, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).