Generated by kicad-footprint-generator · KiCad file format 20260206
LTC3129IUD-1#PBF
Analog Devices · DC-DC Converters · QFN-16-EP(3x3)
LTC3129IUD-1#PBF from Analog Devices, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST1 | passive | Boot-strapped floating supply for the high-side NMOS gate drive; connect to SW1 through a 22nF capacitor as close to the part as possible, with any value from 4.7nF to 47nF usable. |
| 2 | VIN | power_in | Input voltage for the converter; connect a minimum 4.7µF ceramic decoupling capacitor from this pin to the ground plane as close to the pin as possible. |
| 3 | VCC | power_out | Output of the internal voltage regulator that supplies the internal circuitry; bypass with a minimum 2.2µF ceramic capacitor close to the pin, and it may be back-driven by an external supply up to a maximum of 5.5V. |
| 4 | RUN | input | Input to the run comparator; pull above 1.1V to enable the VCC regulator and above 1.28V to enable the converter, and a resistor divider from VIN can set a VIN start threshold higher than the 1.8V typical UVLO threshold. |
| 5 | MPPC | input | Maximum power point control programming pin; connect a resistor divider from VIN to ground to enable MPPC (VIN = 1.175V × [1 + (R5/R6)]), or tie to VCC if the function is not needed. |
| 6 | GND | power_in | Signal ground; provide a short direct PCB path between GND and the ground plane where the exposed pad is soldered. |
| 7 | VS3 | input | Output voltage select pin; connect to ground or VCC per Table 1, must not float or go below ground, and if driven above VCC a 1MΩ series resistor should be added. |
| 8 | VS2 | input | Output voltage select pin; connect to ground or VCC per Table 1, and it must not float or go below ground. |
| 9 | VS1 | input | Output voltage select pin; connect to ground or VCC per Table 1, and it must not float or go below ground. |
| 10 | PWM | input | Mode select pin: low enables automatic Burst Mode operation and high (tied to VCC) enables fixed-frequency PWM; it must not be allowed to float and has an internal 5MΩ pull-down. |
| 11 | PGOOD | output | Open-drain output that pulls to ground when FB drops too far below its regulated voltage; requires an external pull-up resistor and can sink up to the 15mA absolute maximum when low. |
| 12 | VOUT | power_out | Converter output voltage set by VS1-VS3 per Table 1; connect a minimum 4.7µF ceramic capacitor from this pin to the ground plane as close to the pin as possible. |
| 13 | BST2 | passive | Boot-strapped floating supply for the high-side NMOS gate drive; connect to SW2 through a 22nF capacitor as close to the part as possible, with any value from 4.7nF to 47nF usable. |
| 14 | SW2 | bidirectional | Switch pin connected to one side of the inductor; keep PCB trace lengths as short and wide as possible to reduce EMI. |
| 15 | PGND | power_in | Power ground; provide a short direct PCB path between PGND and the ground plane, and it also conducts heat away from the die. |
| 16 | SW1 | bidirectional | Switch pin connected to one side of the inductor; keep PCB trace lengths as short and wide as possible to reduce EMI. |
| 17 | PGND | power_in | Power ground and heat-conduction path from the die; the exposed pad must be soldered to the PCB ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-16-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Start-Up Voltage | 2.25 | 2.42 | V | l: over operating junction temperature range | 3 | ||
| Input Voltage Range | 1.92 | 15 | V | l: over operating junction temperature range; VCC > 2.42V (Back-Driven) | 3 | ||
| VIN UVLO Threshold (Rising) | 1.8 | 1.9 | 2 | V | l: over operating junction temperature range; VCC > 2.42V (Back-Driven) | 3 | |
| VIN UVLO Hysteresis | 80 | 100 | 130 | mV | l: over operating junction temperature range | 3 | |
| VOUT Voltages | VOUT | 2.425 | 2.5 | 2.575 | V | l: over operating junction temperature range; VS1 = VS2 = VS3 = 0V | 3 |
| VOUT Voltages | VOUT | 3.2175 | 3.3 | 3.383 | V | l: over operating junction temperature range; VS1 = VCC, VS2 = VS3 = 0V | 3 |
| VOUT Voltages | VOUT | 3.998 | 4.1 | 4.203 | V | l: over operating junction temperature range; VS2 = VCC, VS1 = VS3 = 0V | 3 |
| VOUT Voltages | VOUT | 4.875 | 5 | 5.125 | V | l: over operating junction temperature range; VS1 = VS2 = VCC, VS3 = 0V | 3 |
| VOUT Voltages | VOUT | 6.727 | 6.9 | 7.073 | V | l: over operating junction temperature range; VS1 = VS2 = 0V, VS3 = VCC | 3 |
| VOUT Voltages | VOUT | 7.995 | 8.2 | 8.405 | V | l: over operating junction temperature range; VS2 = 0V, VS1 = VS3 = VCC | 3 |
| VOUT Voltages | VOUT | 11.64 | 12 | 12.4 | V | l: over operating junction temperature range; VS1 = 0V, VS2 = VS3 = VCC | 3 |
| VOUT Voltages | VOUT | 14.5 | 15 | 15.5 | V | l: over operating junction temperature range; VS1 = VS2 = VS3 = VCC | 3 |
| Quiescent Current (VIN), Shutdown | 10 | 100 | nA | RUN = 0V, Including Switch Leakage | 3 | ||
| Quiescent Current (VIN) UVLO | 1.9 | 3 | µA | Either VIN or VCC Below Their UVLO Threshold, or RUN Below the Threshold to Enable Switching | 3 | ||
| Quiescent Current, Burst Mode Operation | 1.3 | 2 | µA | Measured on VIN, VOUT > VREG; PWM = 0V, RUN = VIN | 3 | ||
| N-Channel Switch Leakage on VIN and VOUT | 10 | 50 | nA | SW1 = 0V, VIN = 15V; SW2 = 0V, VOUT = 15V; RUN = 0V | 3 | ||
| Inductor Average Current Limit | 220 | 275 | 350 | mA | l: over operating junction temperature range; VOUT > UV Threshold (Note 4) | 3 | |
| Inductor Average Current Limit | 80 | 130 | 200 | mA | l: over operating junction temperature range; VOUT < UV Threshold (Note 4) | 3 | |
| Inductor Peak Current Limit | 400 | 500 | 680 | mA | l: over operating junction temperature range; (Note 4) | 3 | |
| Maximum Boost Duty Cycle | 85 | 89 | 95 | % | l: over operating junction temperature range; VOUT < VREG as Set by VS1-VS3. Percentage of Period SW2 is Low in Boost Mode (Note 7) | 3 | |
| Minimum Duty Cycle | 0 | % | l: over operating junction temperature range; VOUT > VREG as Set by VS1-VS3. Percentage of Period SW1 is High in Buck Mode (Note 7) | 3 | |||
| Switching Frequency | 1 | 1.2 | 1.4 | MHz | l: over operating junction temperature range; PWM = VCC | 3 | |
| MPPC Voltage | 1.12 | 1.175 | 1.22 | V | l: over operating junction temperature range | 3 | |
| MPPC Input Current | 1 | 10 | nA | MPPC = 5V | 3 | ||
| RUN Threshold to Enable VCC | 0.5 | 0.9 | 1.15 | V | l: over operating junction temperature range | 3 | |
| RUN Threshold to Enable Switching (Rising) | 1.16 | 1.22 | 1.28 | V | l: over operating junction temperature range; VCC > 2.4V | 3 | |
| RUN (Switching) Threshold Hysteresis | 50 | 80 | 120 | mV | 3 | ||
| RUN Input Current | 1 | 10 | nA | RUN = 15V | 3 | ||
| VS1, VS2, VS3 Input High | 1.2 | V | l: over operating junction temperature range | 3 | |||
| VS1, VS2, VS3 Input Low | 0.4 | V | l: over operating junction temperature range | 3 | |||
| VS1, VS2, VS3 Input Current | 1 | 10 | nA | VS1, VS2, VS3 = VCC = 5V | 3 | ||
| PWM Input High | 1.6 | V | l: over operating junction temperature range | 3 | |||
| PWM Input Low | 0.5 | V | l: over operating junction temperature range | 3 | |||
| PWM Input Current | 0.1 | 1 | µA | PWM = 5V | 3 | ||
| VCC Voltage | 3.4 | 4.1 | 4.7 | V | l: over operating junction temperature range; VIN > 4.85V | 3 | |
| VCC Dropout Voltage (VIN, VCC) | 35 | 60 | mV | VIN = 3.0V, Switching | 3 | ||
| VCC Dropout Voltage (VIN, VCC) | 0 | 2 | mV | VIN = 2.0V (VCC in UVLO) | 3 | ||
| VCC UVLO Threshold (Rising) | 2.1 | 2.25 | 2.42 | V | l: over operating junction temperature range | 4 | |
| VCC Current Limit | 4 | 20 | 60 | mA | l: over operating junction temperature range; VCC = 0V | 4 | |
| VCC Back-Drive Voltage (Maximum) | 5.5 | V | l: over operating junction temperature range | 4 | |||
| VCC Input Current (Back-Driven) | 2 | 4 | mA | VCC = 5.5V (Switching) | 4 | ||
| VOUT UV Threshold (Rising) | 0.95 | 1.15 | 1.35 | V | l: over operating junction temperature range | 4 | |
| VOUT Current, Shutdown | 10 | 100 | nA | RUN = 0V, VOUT = 15V Including Switch Leakage | 4 | ||
| VOUT Current, Active | 5 | 9 | µA | PWM = VCC, VOUT = 15V (Note 4) | 4 | ||
| PGOOD Threshold, Falling | -5.5 | -7.5 | -10 | % | Referenced to Programmed VOUT Voltage | 4 | |
| PGOOD Voltage Low | 250 | 300 | mV | ISINK = 1mA | 4 | ||
| PGOOD Leakage | 1 | 50 | nA | PGOOD = 15V | 4 | ||
| VIN, VOUT Voltages | -0.3 | 18 | V | 2 | |||
| SW1, SW2 Pulsed Voltage | -1 | 19 | V | Pulsed (<100ns) | 2 | ||
| RUN, PGOOD Voltage | -0.3 | 18 | V | 2 | |||
| VCC, PWM, MPPC, VS1, VS2, VS3 Voltages | -0.3 | 6 | V | 2 | |||
| PGOOD Sink Current | 15 | mA | 2 | ||||
| Operating Junction Temperature Range | -40 | 125 | °C | Notes 2, 5 | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Maximum Junction Temperature (QFN) | TJMAX | 125 | °C | 16-lead QFN package | 2 | ||
| Junction-to-Case Thermal Resistance (QFN) | θJC | 7.5 | °C/W | 16-lead QFN package | 2 | ||
| Junction-to-Ambient Thermal Resistance (QFN) | θJA | 68 | °C/W | 16-lead QFN package; Note 6 (exposed pad soldered to PCB) | 2 |
CAD (KiCad official)
- Symbol:
LTC3129IUD-1#PBF - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
ltc3129iud-1-pbf-etched.step/ltc3129iud-1-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc3129iud-1-pbf.step/ltc3129iud-1-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (30 pp, sha256
a197f158aa9bb29c, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).