main
Ray Publish 0.1.0 4405410
{
  "slug": "ltc2924cgn",
  "version": "0.1.0",
  "type": "component",
  "description": "Analog Devices Monitors & Reset Circuits, SSOP-16-150mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "tags": [
    "component",
    "power management ics",
    "ltc2924cgn#trpbf",
    "factory-2.0.0",
    "extractor-text"
  ],
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "ltc2924cgn.kicad_sym",
    "ltc2924cgn.kicad_mod",
    "ltc2924cgn.glb",
    "ltc2924cgn.step",
    "ltc2924cgn.lbr",
    "docs/hero.png",
    "docs/ltc2924cgn-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html",
    "ltc2924cgn-hero.glb",
    "ltc2924cgn-hero.overlay.json"
  ],
  "component": {
    "mpn": "LTC2924CGN",
    "manufacturer": "Analog Devices",
    "package": "SSOP-16-150mil",
    "pin_count": 16,
    "category": "Power Management ICs",
    "subcategory": "Monitors & Reset Circuits",
    "datasheet": "https://www.analog.com/media/en/technical-documentation/data-sheets/2924fc.pdf",
    "parts": {
      "symbol": "ltc2924cgn.kicad_sym",
      "footprint": "ltc2924cgn.kicad_mod",
      "model_3d": "ltc2924cgn-hero.glb",
      "model_3d_plain": "ltc2924cgn.glb",
      "model_3d_step": "ltc2924cgn-etched.step",
      "model_3d_step_plain": "ltc2924cgn.step",
      "lbr": "ltc2924cgn.lbr"
    },
    "distributor_links": {
      "lcsc": "C2657809",
      "digikey": "LTC2924CGN#TRPBFTR-ND",
      "mouser": "584-LTC2924CGN#TRPBF"
    },
    "distributor_check": {
      "checked_at": "2026-11-13T10:14:13Z",
      "source": "Component Ocean /api/assign-pns",
      "digikey": {
        "pn": "LTC2924CGN#TRPBFTR-ND",
        "status": "found"
      },
      "mouser": {
        "pn": "584-LTC2924CGN#TRPBF",
        "status": "found"
      }
    },
    "pins": [
      {
        "number": "1",
        "name": "IN1",
        "type": "input",
        "description": "Sequenced power supply monitor input connected to a resistive divider; 0.61V (typ) indicates the supply is on during Power On or off during Power Off, and hysteresis current (0.5/RHYS) is sourced out of this pin after the threshold is detected."
      },
      {
        "number": "2",
        "name": "IN2",
        "type": "input",
        "description": "Sequenced power supply monitor input connected to a resistive divider; 0.61V (typ) indicates the supply is on during Power On or off during Power Off, and hysteresis current (0.5/RHYS) is sourced out of this pin after the threshold is detected."
      },
      {
        "number": "3",
        "name": "IN3",
        "type": "input",
        "description": "Sequenced power supply monitor input connected to a resistive divider; 0.61V (typ) indicates the supply is on during Power On or off during Power Off, and hysteresis current (0.5/RHYS) is sourced out of this pin after the threshold is detected."
      },
      {
        "number": "4",
        "name": "IN4",
        "type": "input",
        "description": "Sequenced power supply monitor input connected to a resistive divider; 0.61V (typ) indicates the supply is on during Power On or off during Power Off, and hysteresis current (0.5/RHYS) is sourced out of this pin after the threshold is detected."
      },
      {
        "number": "5",
        "name": "OUT1",
        "type": "output",
        "description": "Sequenced power supply enable; low through <240Ω to GND when disabled, and when enabled driven from the internal charge pump (nominally VCC + 5V) via a 10µA (typ) current source, with output voltage limited to VCC + 4.5V (absolute maximum)."
      },
      {
        "number": "6",
        "name": "OUT2",
        "type": "output",
        "description": "Sequenced power supply enable; low through <240Ω to GND when disabled, and when enabled driven from the internal charge pump (nominally VCC + 5V) via a 10µA (typ) current source, with output voltage limited to VCC + 4.5V (absolute maximum)."
      },
      {
        "number": "7",
        "name": "OUT3",
        "type": "output",
        "description": "Sequenced power supply enable; low through <240Ω to GND when disabled, and when enabled driven from the internal charge pump (nominally VCC + 5V) via a 10µA (typ) current source, with output voltage limited to VCC + 4.5V (absolute maximum)."
      },
      {
        "number": "8",
        "name": "OUT4",
        "type": "output",
        "description": "Sequenced power supply enable; low through <240Ω to GND when disabled, and when enabled driven from the internal charge pump (nominally VCC + 5V) via a 10µA (typ) current source, with output voltage limited to VCC + 4.5V (absolute maximum)."
      },
      {
        "number": "9",
        "name": "FAULT",
        "type": "bidirectional",
        "description": "Open-drain fault pin that must be pulled up with an external 10k resistor; the device pulls it low on a detected fault, and an external pull-down below 0.6V held for at least 1µs causes a simultaneous unsequenced power off."
      },
      {
        "number": "10",
        "name": "DONE",
        "type": "output",
        "description": "Open-drain output that must be pulled to VCC with an external 10k resistor; it pulls low when the Power On sequence completes and floats at the end of the Power Off sequence."
      },
      {
        "number": "11",
        "name": "VCC",
        "type": "power_in",
        "description": "Supply input for all internal circuits with a 3V to 6V supply range, to be bypassed with at least 0.1µF to GND close to the device."
      },
      {
        "number": "12",
        "name": "PGT",
        "type": "bidirectional",
        "description": "Power good timer pin where a capacitor to GND sets a 200ms/µF timeout and a fault is asserted if the pin reaches 1V; it must be connected directly to GND to disable the timer and CPGT/CTMR should be kept between 1 and 100."
      },
      {
        "number": "13",
        "name": "GND",
        "type": "power_in",
        "description": "Ground reference for all internal circuits, to be connected to the ground of the power supplies being sequenced."
      },
      {
        "number": "14",
        "name": "TMR",
        "type": "bidirectional",
        "description": "Timer pin where a capacitor to GND sets a 200ms/µF delay between sequenced supplies, may be left floating for minimum delay, is driven to VCC during an internal fault, and must not have any other circuits connected to it."
      },
      {
        "number": "15",
        "name": "HYS/CFG",
        "type": "passive",
        "description": "Hysteresis current setting pin where a resistor to GND (or to VCC on cascaded devices) programs a 0.5/REXT (typ) hysteresis current, with RHYS between 10kΩ and 1MΩ."
      },
      {
        "number": "16",
        "name": "ON",
        "type": "input",
        "description": "On command input that starts the Power On sequence when above 0.61V (typ) and the Power Off sequence when below 0.61V, with hysteresis current applied while above threshold."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.3",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.3",
        "primary_model": "claude-haiku-5-5",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [
          "extractor flagged: Pin numbers were taken from the GN package top-view layout (pins 1-8 on the left, 9-16 on the right,"
        ],
        "pages_sent": 22,
        "cost_usd": 0.104,
        "at": "2026-11-13T10:14:00"
      },
      "datasheet": {
        "url": "https://www.analog.com/media/en/technical-documentation/data-sheets/2924fc.pdf",
        "pages": 22,
        "sha256": "024f313858bb1c22",
        "source_tier": "mfr"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 16,
        "described": 16,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "ltc2924cgn.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          6.0,
          4.9,
          1.85
        ],
        "zmin_mm": -0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "3b55ed1c8dc3eb976cfab8b1e135fd29a17f33ebf575a8a088a30e82c9a5f2ee",
        "checked": "2026-11-13",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "ltc2924cgn-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          6.0,
          4.9,
          1.85
        ],
        "zmin_mm": -0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "c7e251e166b47b80dd63433c4f60b3d7a2bf1aa43c09fd5223707752b51f4eb4",
        "checked": "2026-11-13",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  }
}