main
History Download
Ray Publish 0.1.0 4405410

LTC2924CGN#TRPBF

Analog Devices · Monitors & Reset Circuits · SSOP-16-150mil

LTC2924CGN#TRPBF from Analog Devices, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IN1 input Sequenced power supply monitor input connected to a resistive divider; 0.61V (typ) indicates the supply is on during Power On or off during Power Off, and hysteresis current (0.5/RHYS) is sourced out of this pin after the threshold is detected.
2 IN2 input Sequenced power supply monitor input connected to a resistive divider; 0.61V (typ) indicates the supply is on during Power On or off during Power Off, and hysteresis current (0.5/RHYS) is sourced out of this pin after the threshold is detected.
3 IN3 input Sequenced power supply monitor input connected to a resistive divider; 0.61V (typ) indicates the supply is on during Power On or off during Power Off, and hysteresis current (0.5/RHYS) is sourced out of this pin after the threshold is detected.
4 IN4 input Sequenced power supply monitor input connected to a resistive divider; 0.61V (typ) indicates the supply is on during Power On or off during Power Off, and hysteresis current (0.5/RHYS) is sourced out of this pin after the threshold is detected.
5 OUT1 output Sequenced power supply enable; low through <240Ω to GND when disabled, and when enabled driven from the internal charge pump (nominally VCC + 5V) via a 10µA (typ) current source, with output voltage limited to VCC + 4.5V (absolute maximum).
6 OUT2 output Sequenced power supply enable; low through <240Ω to GND when disabled, and when enabled driven from the internal charge pump (nominally VCC + 5V) via a 10µA (typ) current source, with output voltage limited to VCC + 4.5V (absolute maximum).
7 OUT3 output Sequenced power supply enable; low through <240Ω to GND when disabled, and when enabled driven from the internal charge pump (nominally VCC + 5V) via a 10µA (typ) current source, with output voltage limited to VCC + 4.5V (absolute maximum).
8 OUT4 output Sequenced power supply enable; low through <240Ω to GND when disabled, and when enabled driven from the internal charge pump (nominally VCC + 5V) via a 10µA (typ) current source, with output voltage limited to VCC + 4.5V (absolute maximum).
9 FAULT bidirectional Open-drain fault pin that must be pulled up with an external 10k resistor; the device pulls it low on a detected fault, and an external pull-down below 0.6V held for at least 1µs causes a simultaneous unsequenced power off.
10 DONE output Open-drain output that must be pulled to VCC with an external 10k resistor; it pulls low when the Power On sequence completes and floats at the end of the Power Off sequence.
11 VCC power_in Supply input for all internal circuits with a 3V to 6V supply range, to be bypassed with at least 0.1µF to GND close to the device.
12 PGT bidirectional Power good timer pin where a capacitor to GND sets a 200ms/µF timeout and a fault is asserted if the pin reaches 1V; it must be connected directly to GND to disable the timer and CPGT/CTMR should be kept between 1 and 100.
13 GND power_in Ground reference for all internal circuits, to be connected to the ground of the power supplies being sequenced.
14 TMR bidirectional Timer pin where a capacitor to GND sets a 200ms/µF delay between sequenced supplies, may be left floating for minimum delay, is driven to VCC during an internal fault, and must not have any other circuits connected to it.
15 HYS/CFG passive Hysteresis current setting pin where a resistor to GND (or to VCC on cascaded devices) programs a 0.5/REXT (typ) hysteresis current, with RHYS between 10kΩ and 1MΩ.
16 ON input On command input that starts the Power On sequence when above 0.61V (typ) and the Power Off sequence when below 0.61V, with hysteresis current applied while above threshold.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package SSOP-16-150mil
Category Power Management ICs
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VCC Input Supply Range VCC 3 6 V 3
Input Supply Current ICC 1.5 3 mA 3
ON, Low to High Threshold VON(TH) 0.6 0.606 0.6121 V 3
ON, High to Low Threshold VOFF(TH) 0.6014 0.6074 0.6135 V 3
IN1-IN4 Low to High Threshold VON(TH) 0.602 0.6081 0.6142 V 3
IN1-IN4 High to Low Threshold VOFF(TH) 0.6026 0.6087 0.6148 V 3
ON, IN1-IN4 High Speed Low Fault Threshold VFAULT 0.33 0.4 0.48 V 3
ON, IN1-IN4 Hysteresis Current Range ION(HYS) 0.5 50 µA VON ≥ VON(TH) (Note 2) 3
ON, IN1-IN4 Hysteresis Current Error (0.5µA ≤ ION < 25µA) ION(ERROR) -22 22 % VON(TH) = 1V; 0.5µA ≤ ION < 25µA 3
ON, IN1-IN4 Hysteresis Current Error (25µA ≤ ION ≤ 50µA) ION(ERROR) -10 10 % VON(TH) = 1V; 25µA ≤ ION ≤ 50µA 3
ON, IN1-IN4 Leakage (Below Threshold) ILEAK -100 2 100 nA VON(TH) = 0.5V 3
ON, IN1-IN4 Minimum Hysteresis Voltage VON(HYS) 4 mV IHYS • RIN (Note 6) 3
OUT1-OUT4 On Current IOUT(EN) 8.6 10 11.2 µA OUTn On, VOUT = (VCC + 4V) 3
OUT1-OUT4 Off Resistance to GND ROUT(OFF) 240 Ω OUTn Off, IOUT = 2mA 3
Timer Pin Output Current ITMR 4 5 6 µA Timer On, VTMR ≤ 0.9V 3
Timer High Voltage Threshold VTH(HI) 0.93 1 1.07 V VCC = 5V 3
Power Good Timer Pin Output Current IPGT 4 5 6 µA Power Good Timer On, VPGT ≤ 0.9V 3
Power Good Timer Fault Detected Voltage Threshold VPGT 0.93 1 1.07 V VCC = 5V 3
DONE Pin Pull-Down Resistance to GND RD(LO) 100 Ω DONE = Low, I = 2mA 4
DONE Pin Off Leakage Current ID(HI) 15 µA DONE = High 4
FAULT Pin Pull-Down Resistance to GND RFAULT(LO) 400 Ω FAULT Being Pulled Low Internally, I = 2mA 4
FAULT Pin Off Leakage Current IFAULT(HI) 2 µA FAULT High 4
Voltage Above Which an Externally Generated FAULT Condition Will Not be Detected VFAULT(HI) 1.6 V 4
Voltage Below Which an Externally Generated FAULT Condition Will be Detected VFAULT(LO) 0.6 V 4
External Pull-Up Resistance on FAULT RF(EXT) 10 kΩ 4
Externally Commanded FAULT Below VFAULT(LO) to OUT1-OUT4 Pull-Down On Delay tFAULT 1 µs 4
Externally Commanded FAULT Minimum Time Below VFAULT(LO) tFAULT(MIN) 1 µs Determined by design, not production tested (Note 4) 4
Supply Voltage (VCC) VCC -0.3 6.5 V 2
Operating Temperature Range, LTC2924C TA 0 70 °C LTC2924CGN (commercial grade) 2
Storage Temperature Range TSTG -65 150 °C 2
Maximum Junction Temperature TJMAX 125 °C 2
Junction-to-Ambient Thermal Resistance θJA 130 °C/W GN package 2

CAD (KiCad official)

  • Symbol: LTC2924CGN#TRPBF
  • Footprint: Package_SO:SSOP-16_3.9x4.9mm_P0.635mm
  • 3D model: SSOP-16-150mil (KiCad packages3D, STEP)
  • 3D model files: ltc2924cgn-etched.step / ltc2924cgn-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ltc2924cgn.step / ltc2924cgn.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (22 pp, sha256 024f313858bb1c22, retrieved 2026-11-13, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF