main
Ray
Publish 0.1.0
2745573
LTC2855IGN#TRPBF
Analog Devices · RS-485/RS-422 ICs · SSOP-16-150mil
LTC2855IGN#TRPBF from Analog Devices, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver output: goes high when A > B by 200mV and low when A < B by 200mV, and stays high if the inputs are open, shorted, or terminated without a signal; it is high-impedance when the receiver is disabled (RE high). |
| 2 | RE | input | Receiver enable: a low enables the receiver, and a high forces RO into a high-impedance state. |
| 3 | DE | input | Driver enable: a high enables the driver and a low forces the driver outputs into high impedance; with RE high and TE low the part enters low-power shutdown. |
| 4 | DI | input | Driver input: with the driver enabled, a low on DI drives Y low and Z high, and a high on DI drives Y high and Z low. |
| 5 | TE | input | Internal termination enable: a high connects a 120Ω typical termination resistor between pins A and B. |
| 6 | GND | power_in | Ground reference for the device. |
| 7 | NC | unconnected | No internal connection. |
| 8 | NC | unconnected | No internal connection. |
| 9 | NC | unconnected | No internal connection. |
| 10 | NC | unconnected | No internal connection. |
| 11 | NC | unconnected | No internal connection. |
| 12 | Y | output | Positive (non-inverting) driver output for the LTC2855; driver outputs are protected from shorts to any voltage between (VCC -15V) and +15V and have ESD protection of ±15kV HBM. |
| 13 | Z | output | Negative (inverting) driver output for the LTC2855; driver outputs are protected from shorts to any voltage between (VCC -15V) and +15V and have ESD protection of ±15kV HBM. |
| 14 | B | input | Negative receiver input; the receiver input resistance is greater than 96kΩ (C-, I-Grade) with termination disabled, and the common-mode range is -7V to +12V. |
| 15 | A | input | Positive receiver input; the receiver input resistance is greater than 96kΩ (C-, I-Grade) with termination disabled, and the common-mode range is -7V to +12V. |
| 16 | VCC | power_in | Positive supply, specified for 3.0V to 3.6V; bypass with a 0.1µF ceramic capacitor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SSOP-16-150mil |
| Category | Interface ICs |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Differential driver output voltage (R = 27Ω, VCC = 3V) | /VOD/ | 1.5 | V | R = 27Ω, VCC = 3V (Figure 1) | 3 | ||
| Differential driver output voltage (R = 50Ω, VCC = 3.13V) | /VOD/ | 2 | V | R = 50Ω, VCC = 3.13V (Figure 1) | 3 | ||
| Change in magnitude of driver differential output voltage for complementary states | D/VOD/ | 0.2 | V | R = 27Ω or R = 50Ω (Figure 1) | 3 | ||
| Driver common mode output voltage | VOC | 3 | V | R = 27Ω or R = 50Ω (Figure 1) | 3 | ||
| Change in magnitude of driver common mode output voltage for complementary states | D/VOC/ | 0.2 | V | R = 27Ω or R = 50Ω (Figure 1) | 3 | ||
| Driver three-state output current on Y and Z (C-, I-Grade) | IOZD | -10 | 10 | µA | DE = OV, (Y or Z) = -7V, 12V (LTC2855) | 3 | |
| Maximum driver short-circuit current | IOSD | -250 | 180 | 250 | mA | -7V ≤ (Y or Z) ≤ 12V (Figure 2) | 3 |
| Receiver input current (A, B), VIN = 12V (C-, I-Grade) | IIN | 125 | µA | DE = TE = 0V, VCC = 0V or 3.3V, VIN = 12V (Figure 3) | 3 | ||
| Receiver input current (A, B), VIN = -7V (C-, I-Grade) | IIN | -100 | µA | DE = TE = 0V, VCC = 0V or 3.3V, VIN = -7V (Figure 3) | 3 | ||
| Receiver input resistance (C-, I-Grade) | RIN | 96 | 125 | kΩ | RE = VCC or 0V, DE = TE = 0V, VIN = -7V, -3V, 3V, 7V, 12V (Figure 3) | 3 | |
| Receiver differential input threshold voltage | VTH | -0.2 | 0.2 | V | -7V ≤ B ≤ 12V | 3 | |
| Receiver output HIGH voltage | VOH | 2.4 | V | I(RO) = -4mA, A-B = 200mV, VCC = 3V | 3 | ||
| Receiver output LOW voltage | VOL | 0.4 | V | I(RO) = 4mA, A-B = -200mV, VCC = 3V | 3 | ||
| Receiver three-state output current on RO | IOZR | -1 | 1 | µA | RE = VCC, 0V ≤ RO ≤ VCC | 3 | |
| Receiver short-circuit current | IOSR | -85 | 85 | mA | 0V ≤ RO ≤ VCC | 3 | |
| Receiver input terminating resistor | RTERM | 108 | 120 | 156 | Ω | TE = VCC, VAB = 2V, VB = -7V, 0V, 10V (Figure 8) | 3 |
| Logic input high voltage | VIH | 2 | V | VCC = 3.6V | 3 | ||
| Logic input low voltage | VIL | 0.8 | V | VCC = 3V | 3 | ||
| Logic input current | IINL | -10 | 0 | 10 | µA | 3 | |
| Supply current in shutdown mode (C-, I-Grade) | ICCS | 0 | 5 | µA | DE = 0V, RE = VCC, TE = 0V | 3 | |
| Supply current in receive mode | ICCR | 370 | 900 | µA | DE = 0V, RE = 0V, TE = 0V | 3 | |
| Maximum data rate | fMAX | 20 | Mbps | Note 3 | 4 | ||
| Driver input to output propagation delay | tPLHD, tPHLD | 10 | 50 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 4 | |
| Driver input to output delay difference | DtPD | 1 | 6 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 4 | |
| Driver output Y to output Z skew | tSKEWD | -6 | 1 | 6 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 4 |
| Driver rise or fall time | tRD, tFD | 4 | 12.5 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 4 | |
| Driver enable or disable time | tZLD, tZHD, tLZD, tHZD | 70 | ns | RL = 500Ω, CL = 50pF, RE = 0 (Figure 5) | 4 | ||
| Driver enable from shutdown | tZHSD, tZLSD | 8 | µs | RL = 500Ω, CL = 50pF, RE = VCC (Figure 5) | 4 | ||
| Time to shutdown | tSHDN | 100 | ns | RL = 500Ω, CL = 50pF (DE = ↓, RE = VCC) or (DE = 0, RE ↑) (Figure 5) | 4 | ||
| Receiver input to output propagation delay | tPLHR, tPHLR | 50 | 70 | ns | CL = 15pF, VCM = 1.5V, /VAB/ = 1.5V, tR and tF < 4ns (Figure 6) | 4 | |
| Differential receiver skew | tSKEWR | 1 | 6 | ns | CL = 15pF (Figure 6) | 4 | |
| Receiver output rise or fall time | tRR, tFR | 3 | 12.5 | ns | CL = 15pF (Figure 6) | 4 | |
| Receiver enable or disable time | tZLR, tZHR, tLZR, tHZR | 50 | ns | RL = 1k, CL = 15pF, DE = VCC (Figure 7) | 4 | ||
| Receiver enable from shutdown | tZHSR, tZLSR | 8 | µs | RL = 1k, CL = 15pF, DE = 0V (Figure 7) | 4 | ||
| Termination enable or disable time | tRTEN, tRTZ | 100 | µs | VB = 0V, VAB = 2V, RE = VCC, DE = 0V (Figure 8) | 4 | ||
| Supply current in transmit mode | ICCT | 450 | 1000 | µA | No load, DE = VCC, RE = VCC, TE = 0V | 4 | |
| Supply current with driver and receiver enabled | ICCTR | 450 | 1000 | µA | No load, DE = VCC, RE = 0V, TE = 0V | 4 | |
| Supply current in termination mode | ICCTERM | 110 | 180 | µA | DE = 0V, RE = VCC, TE = VCC | 4 | |
| Supply current in receive and termination mode | ICCTERMR | 450 | 950 | µA | DE = 0V, RE = 0V, TE = VCC | 4 | |
| Supply current in transmit and termination mode | ICCTERMT | 470 | 1000 | µA | DE = VCC, RE = VCC, TE = VCC | 4 | |
| Supply current with driver, receiver and termination enabled | ICCTERMTR | 470 | 1000 | µA | DE = VCC, RE = 0V, TE = VCC | 4 | |
| ESD protection, human body model (Y, Z, A, B on LTC2855) | ESD HBM | -15 | 15 | kV | Human body model, Y, Z, A, B on LTC2855 | 4 | |
| Supply voltage | VCC | -0.3 | 7 | V | 2 | ||
| Logic input voltages (RE, DE, DI, TE) | -0.3 | 7 | V | 2 | |||
| Interface I/O voltage (A, B, Y, Z) | 15 | V | 2 | ||||
| (A-B) or (B-A) differential voltage with terminator enabled | 6 | V | Terminator enabled | 2 | |||
| Receiver output voltage (RO) | RO | -0.3 | V | Referenced to VCC +0.3V (Note 1) | 2 | ||
| Operating temperature range (LTC2855I) | -40 | 85 | °C | LTC2855I | 2 | ||
| Storage temperature range | -65 | 150 | °C | 2 | |||
| Lead temperature (soldering, 10 sec) | 300 | °C | GN package, 10 sec soldering | 2 | |||
| Maximum junction temperature | TJMAX | 150 | °C | GN16 package | 2 | ||
| Supply voltage (recommended) | VCC | 3 | 3.6 | V | 3.0V < VCC < 3.6V (pin function description) | 8 | |
| Thermal resistance, junction to ambient | θJA | 110 | °C/W | GN16 (SSOP) package | 2 | ||
| Thermal resistance, junction to case | θJC | 40 | °C/W | GN16 (SSOP) package | 2 |
CAD (KiCad official)
- Symbol:
LTC2855IGN#TRPBF - Footprint:
Package_SO:SSOP-16_3.9x4.9mm_P0.635mm - 3D model: SSOP-16-150mil (KiCad packages3D, STEP)
- 3D model files:
ltc2855ign-etched.step/ltc2855ign-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc2855ign.step/ltc2855ign.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (18 pp, sha256
78130b7ef684fd8c, retrieved 2026-11-13, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LTC2855IGN#TRPBF
**Analog Devices** · RS-485/RS-422 ICs · SSOP-16-150mil
LTC2855IGN#TRPBF from Analog Devices, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver output: goes high when A > B by 200mV and low when A < B by 200mV, and stays high if the inputs are open, shorted, or terminated without a signal; it is high-impedance when the receiver is disabled (RE high). |
| 2 | RE | input | Receiver enable: a low enables the receiver, and a high forces RO into a high-impedance state. |
| 3 | DE | input | Driver enable: a high enables the driver and a low forces the driver outputs into high impedance; with RE high and TE low the part enters low-power shutdown. |
| 4 | DI | input | Driver input: with the driver enabled, a low on DI drives Y low and Z high, and a high on DI drives Y high and Z low. |
| 5 | TE | input | Internal termination enable: a high connects a 120Ω typical termination resistor between pins A and B. |
| 6 | GND | power_in | Ground reference for the device. |
| 7 | NC | unconnected | No internal connection. |
| 8 | NC | unconnected | No internal connection. |
| 9 | NC | unconnected | No internal connection. |
| 10 | NC | unconnected | No internal connection. |
| 11 | NC | unconnected | No internal connection. |
| 12 | Y | output | Positive (non-inverting) driver output for the LTC2855; driver outputs are protected from shorts to any voltage between (VCC -15V) and +15V and have ESD protection of ±15kV HBM. |
| 13 | Z | output | Negative (inverting) driver output for the LTC2855; driver outputs are protected from shorts to any voltage between (VCC -15V) and +15V and have ESD protection of ±15kV HBM. |
| 14 | B | input | Negative receiver input; the receiver input resistance is greater than 96kΩ (C-, I-Grade) with termination disabled, and the common-mode range is -7V to +12V. |
| 15 | A | input | Positive receiver input; the receiver input resistance is greater than 96kΩ (C-, I-Grade) with termination disabled, and the common-mode range is -7V to +12V. |
| 16 | VCC | power_in | Positive supply, specified for 3.0V to 3.6V; bypass with a 0.1µF ceramic capacitor. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SSOP-16-150mil |
| Category | Interface ICs |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Differential driver output voltage (R = 27Ω, VCC = 3V) | /VOD/ | 1.5 | | | V | R = 27Ω, VCC = 3V (Figure 1) | 3 |
| Differential driver output voltage (R = 50Ω, VCC = 3.13V) | /VOD/ | 2 | | | V | R = 50Ω, VCC = 3.13V (Figure 1) | 3 |
| Change in magnitude of driver differential output voltage for complementary states | D/VOD/ | | | 0.2 | V | R = 27Ω or R = 50Ω (Figure 1) | 3 |
| Driver common mode output voltage | VOC | | | 3 | V | R = 27Ω or R = 50Ω (Figure 1) | 3 |
| Change in magnitude of driver common mode output voltage for complementary states | D/VOC/ | | | 0.2 | V | R = 27Ω or R = 50Ω (Figure 1) | 3 |
| Driver three-state output current on Y and Z (C-, I-Grade) | IOZD | -10 | | 10 | µA | DE = OV, (Y or Z) = -7V, 12V (LTC2855) | 3 |
| Maximum driver short-circuit current | IOSD | -250 | 180 | 250 | mA | -7V ≤ (Y or Z) ≤ 12V (Figure 2) | 3 |
| Receiver input current (A, B), VIN = 12V (C-, I-Grade) | IIN | | | 125 | µA | DE = TE = 0V, VCC = 0V or 3.3V, VIN = 12V (Figure 3) | 3 |
| Receiver input current (A, B), VIN = -7V (C-, I-Grade) | IIN | -100 | | | µA | DE = TE = 0V, VCC = 0V or 3.3V, VIN = -7V (Figure 3) | 3 |
| Receiver input resistance (C-, I-Grade) | RIN | 96 | 125 | | kΩ | RE = VCC or 0V, DE = TE = 0V, VIN = -7V, -3V, 3V, 7V, 12V (Figure 3) | 3 |
| Receiver differential input threshold voltage | VTH | -0.2 | | 0.2 | V | -7V ≤ B ≤ 12V | 3 |
| Receiver output HIGH voltage | VOH | 2.4 | | | V | I(RO) = -4mA, A-B = 200mV, VCC = 3V | 3 |
| Receiver output LOW voltage | VOL | | | 0.4 | V | I(RO) = 4mA, A-B = -200mV, VCC = 3V | 3 |
| Receiver three-state output current on RO | IOZR | -1 | | 1 | µA | RE = VCC, 0V ≤ RO ≤ VCC | 3 |
| Receiver short-circuit current | IOSR | -85 | | 85 | mA | 0V ≤ RO ≤ VCC | 3 |
| Receiver input terminating resistor | RTERM | 108 | 120 | 156 | Ω | TE = VCC, VAB = 2V, VB = -7V, 0V, 10V (Figure 8) | 3 |
| Logic input high voltage | VIH | 2 | | | V | VCC = 3.6V | 3 |
| Logic input low voltage | VIL | | | 0.8 | V | VCC = 3V | 3 |
| Logic input current | IINL | -10 | 0 | 10 | µA | | 3 |
| Supply current in shutdown mode (C-, I-Grade) | ICCS | 0 | | 5 | µA | DE = 0V, RE = VCC, TE = 0V | 3 |
| Supply current in receive mode | ICCR | | 370 | 900 | µA | DE = 0V, RE = 0V, TE = 0V | 3 |
| Maximum data rate | fMAX | 20 | | | Mbps | Note 3 | 4 |
| Driver input to output propagation delay | tPLHD, tPHLD | | 10 | 50 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 4 |
| Driver input to output delay difference | DtPD | | 1 | 6 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 4 |
| Driver output Y to output Z skew | tSKEWD | -6 | 1 | 6 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 4 |
| Driver rise or fall time | tRD, tFD | | 4 | 12.5 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 4 |
| Driver enable or disable time | tZLD, tZHD, tLZD, tHZD | | | 70 | ns | RL = 500Ω, CL = 50pF, RE = 0 (Figure 5) | 4 |
| Driver enable from shutdown | tZHSD, tZLSD | | | 8 | µs | RL = 500Ω, CL = 50pF, RE = VCC (Figure 5) | 4 |
| Time to shutdown | tSHDN | | | 100 | ns | RL = 500Ω, CL = 50pF (DE = ↓, RE = VCC) or (DE = 0, RE ↑) (Figure 5) | 4 |
| Receiver input to output propagation delay | tPLHR, tPHLR | | 50 | 70 | ns | CL = 15pF, VCM = 1.5V, /VAB/ = 1.5V, tR and tF < 4ns (Figure 6) | 4 |
| Differential receiver skew | tSKEWR | | 1 | 6 | ns | CL = 15pF (Figure 6) | 4 |
| Receiver output rise or fall time | tRR, tFR | | 3 | 12.5 | ns | CL = 15pF (Figure 6) | 4 |
| Receiver enable or disable time | tZLR, tZHR, tLZR, tHZR | | | 50 | ns | RL = 1k, CL = 15pF, DE = VCC (Figure 7) | 4 |
| Receiver enable from shutdown | tZHSR, tZLSR | | | 8 | µs | RL = 1k, CL = 15pF, DE = 0V (Figure 7) | 4 |
| Termination enable or disable time | tRTEN, tRTZ | | | 100 | µs | VB = 0V, VAB = 2V, RE = VCC, DE = 0V (Figure 8) | 4 |
| Supply current in transmit mode | ICCT | | 450 | 1000 | µA | No load, DE = VCC, RE = VCC, TE = 0V | 4 |
| Supply current with driver and receiver enabled | ICCTR | | 450 | 1000 | µA | No load, DE = VCC, RE = 0V, TE = 0V | 4 |
| Supply current in termination mode | ICCTERM | | 110 | 180 | µA | DE = 0V, RE = VCC, TE = VCC | 4 |
| Supply current in receive and termination mode | ICCTERMR | | 450 | 950 | µA | DE = 0V, RE = 0V, TE = VCC | 4 |
| Supply current in transmit and termination mode | ICCTERMT | | 470 | 1000 | µA | DE = VCC, RE = VCC, TE = VCC | 4 |
| Supply current with driver, receiver and termination enabled | ICCTERMTR | | 470 | 1000 | µA | DE = VCC, RE = 0V, TE = VCC | 4 |
| ESD protection, human body model (Y, Z, A, B on LTC2855) | ESD HBM | -15 | | 15 | kV | Human body model, Y, Z, A, B on LTC2855 | 4 |
| Supply voltage | VCC | -0.3 | | 7 | V | | 2 |
| Logic input voltages (RE, DE, DI, TE) | | -0.3 | | 7 | V | | 2 |
| Interface I/O voltage (A, B, Y, Z) | | | | 15 | V | | 2 |
| (A-B) or (B-A) differential voltage with terminator enabled | | | | 6 | V | Terminator enabled | 2 |
| Receiver output voltage (RO) | RO | -0.3 | | | V | Referenced to VCC +0.3V (Note 1) | 2 |
| Operating temperature range (LTC2855I) | | -40 | | 85 | °C | LTC2855I | 2 |
| Storage temperature range | | -65 | | 150 | °C | | 2 |
| Lead temperature (soldering, 10 sec) | | | | 300 | °C | GN package, 10 sec soldering | 2 |
| Maximum junction temperature | TJMAX | | | 150 | °C | GN16 package | 2 |
| Supply voltage (recommended) | VCC | 3 | | 3.6 | V | 3.0V < VCC < 3.6V (pin function description) | 8 |
| Thermal resistance, junction to ambient | θJA | | 110 | | °C/W | GN16 (SSOP) package | 2 |
| Thermal resistance, junction to case | θJC | | 40 | | °C/W | GN16 (SSOP) package | 2 |
## CAD (KiCad official)
- Symbol: `LTC2855IGN#TRPBF`
- Footprint: `Package_SO:SSOP-16_3.9x4.9mm_P0.635mm`
- 3D model: SSOP-16-150mil (KiCad packages3D, STEP)
- 3D model files: `ltc2855ign-etched.step` / `ltc2855ign-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ltc2855ign.step` / `ltc2855ign.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/285455fc.pdf) (18 pp, sha256 `78130b7ef684fd8c`, retrieved 2026-11-13, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ltc2855ign-datasheet.pdf)