3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLTC2850IMS8#PBF
Analog Devices · RS-485/RS-422 ICs · MSOP-8
LTC2850IMS8#PBF from Analog Devices, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver output: goes high when A-B is greater than +200mV, low when A-B is less than -200mV, and high when the inputs are open, shorted, or undriven; it is high-impedance when the receiver is disabled (RE high). |
| 2 | RE | input | Receiver enable: a low enables the receiver and a high forces RO into a high-impedance state; RE high with DE low puts the part into low-power shutdown. |
| 3 | DE | input | Driver enable: a high enables the driver, and a low forces the driver outputs into high impedance; RE high with DE low enters low-power shutdown. |
| 4 | DI | input | Driver input: with the driver enabled (DE high), a high on DI drives A high and B low, and a low on DI drives A low and B high. |
| 5 | GND | power_in | Ground reference for the device; the datasheet references all voltages to device ground. |
| 6 | A | bidirectional | Noninverting receiver input and noninverting driver output on the LTC2850; input impedance is greater than 96kΩ in receive mode or when unpowered, and the bus common-mode range is -7V to 12V. |
| 7 | B | bidirectional | Inverting receiver input and inverting driver output on the LTC2850; input impedance is greater than 96kΩ in receive mode or when unpowered, and the bus common-mode range is -7V to 12V. |
| 8 | VCC | power_in | Positive supply: 3V ≤ VCC ≤ 3.6V; the datasheet recommends bypassing with a 0.1µF ceramic capacitor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-8 |
| Category | Communication Interface Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | -0.3 | 7 | V | 2 | ||
| Logic Input Voltages (RE, DE, DI) | -0.3 | 7 | V | 2 | |||
| Interface I/O Voltage (A, B, Y, Z) | 15 | V | Lower limit printed as (VCC, 15V) | 2 | |||
| Receiver Output Voltage | RO | -0.3 | V | Upper limit printed as (VCC + 0.3V) | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Maximum Junction Temperature | TJMAX | 150 | °C | 2 | |||
| Operating Temperature Range (I-Grade) | -40 | 85 | °C | LTC285xI | 2 | ||
| Positive Supply Voltage | VCC | 3 | 3.6 | V | 9 | ||
| Differential Driver Output Voltage | /VOD/ | 1.5 | V | R = ∞, VCC = 3V (Figure 1) | 4 | ||
| Differential Driver Output Voltage | /VOD/ | 2 | V | R = 27Ω, VCC = 3V (Figure 1) | 4 | ||
| Difference in Magnitude of Driver Differential Output Voltage for Complementary Output States | Δ/VOD/ | 0.2 | V | R = 27Ω or 50Ω (Figure 1) | 4 | ||
| Driver Common Mode Output Voltage | VOC | 3 | V | R = 27Ω or 50Ω (Figure 1) | 4 | ||
| Difference in Magnitude of Driver Common Mode Output Voltage for Complementary Output States | Δ/VOC/ | 0.2 | V | R = 27Ω or 50Ω (Figure 1) | 4 | ||
| Maximum Driver Short-Circuit Current | IOSD | -250 | 180 | 250 | mA | -7V ≤ (Y or Z) ≤ 12V (Figure 2) | 4 |
| Receiver Input Current (A, B) | IIN | 125 | µA | DE = TE = 0V, VCC = 0V or 3.3V, VIN = 12V (Figure 3) (C, I-Grade) | 4 | ||
| Receiver Input Current (A, B) | IIN | -100 | µA | DE = TE = 0V, VCC = 0V or 3.3V, VIN = -7V (Figure 3) (C, I-Grade) | 4 | ||
| Receiver Input Resistance | RIN | 96 | 125 | kΩ | RE = VCC or 0V, DE = TE = 0V, VIN = -7V, -3V, 3V, 7V, 12V (Figure 3) (C, I-Grade) | 4 | |
| Receiver Differential Input Threshold Voltage | VTH | -0.2 | 0.2 | V | -7V ≤ B ≤ 12V | 4 | |
| Receiver Output High Voltage | VOH | 2.4 | V | I(RO) = -4mA, A-B = 200mV, VCC = 3V | 4 | ||
| Receiver Output Low Voltage | VOL | 0.4 | V | I(RO) = 4mA, A-B = -200mV, VCC = 3V | 4 | ||
| Receiver Three-State Output Current on RO | IOZR | -1 | 1 | µA | RE = VCC, 0V ≤ RO ≤ VCC (LTC2850, LTC2852) | 4 | |
| Receiver Short-Circuit Current | IOSR | -85 | 85 | mA | 0V ≤ RO ≤ VCC | 4 | |
| Logic Input High Voltage | VIH | 2 | V | VCC = 3.6V | 4 | ||
| Logic Input Low Voltage | VIL | 0.8 | V | VCC = 3V | 4 | ||
| Logic Input Current | IINL | -10 | 0 | 10 | µA | 4 | |
| Maximum Data Rate | fMAX | 20 | Mbps | 5 | |||
| Driver Input to Output | tPLHD, tPHLD | 10 | 50 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 5 | |
| Driver Input to Output Difference /tPLHD, tPHLD/ | ΔtPD | 1 | 6 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 5 | |
| Driver Output Skew | tSKEWD | -6 | 1 | 6 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 5 |
| Driver Rise or Fall Time | tRD, tFD | 4 | 12.5 | ns | RDIFF = 54Ω, CL = 100pF (Figure 4) | 5 | |
| Driver Enable or Disable Time | tZLD, tZHD, tLZD, tHZD | 70 | ns | RL = 500Ω, CL = 50pF, RE = 0V (Figure 5) (LTC2850, LTC2852) | 5 | ||
| Driver Enable from Shutdown | tZHSD, tZLSD | 8 | µs | RL = 500Ω, CL = 50pF, RE = VCC (Figure 5) (LTC2850, LTC2852) | 5 | ||
| Time to Shutdown | tSHDN | 100 | ns | RL = 500Ω, CL = 50pF, (DE = ↓, RE = VCC) or (DE = 0V, RE = ↑) (Figure 5) (LTC2850, LTC2852) | 5 | ||
| Receiver Input to Output | tPLHR, tPHLR | 50 | 70 | ns | CL = 15pF, VCM = 1.5V, /VAB/ = 1.5V, tR and tF < 4ns (Figure 6) | 5 | |
| Differential Receiver Skew /tPLHR, tPHLR/ | tSKEWR | 1 | 6 | ns | CL = 15pF (Figure 6) | 5 | |
| Receiver Output Rise or Fall Time | tRR, tFR | 3 | 12.5 | ns | CL = 15pF (Figure 6) | 5 | |
| Receiver Enable/Disable | tZLR, tZHR, tLZR, tHZR | 50 | ns | RL = 1k, CL = 15pF, DE = VCC (Figure 7) (LTC2850, LTC2852) | 5 | ||
| Receiver Enable from Shutdown | tZHSR, tZLSR | 8 | µs | RL = 1k, CL = 15pF, DE = 0V (Figure 7) (LTC2850, LTC2852) | 5 | ||
| Supply Current in Shutdown Mode | ICCS | 0 | 5 | µA | DE = 0V, RE = VCC, LTC2850, LTC2852 (C and I-Grade) | 5 | |
| Supply Current in Receive Mode | ICCR | 370 | 900 | µA | DE = 0V, RE = 0V (LTC2850, LTC2852) | 5 | |
| Supply Current in Transmit Mode | ICCT | 450 | 1000 | µA | No Load, DE = VCC, RE = VCC (LTC2850, LTC2852) | 5 | |
| Supply Current with Both Driver and Receiver Enabled | ICCTR | 450 | 1000 | µA | No Load, DE = VCC, RE = 0V | 5 | |
| Receiver Input Hysteresis | ΔVTH | 25 | mV | B = 0V | 4 | ||
| Thermal Resistance, Junction-to-Ambient (MS8) | θJA | 200 | °C/W | MS8 package | 2 | ||
| Thermal Resistance, Junction-to-Case (MS8) | θJC | 40 | °C/W | MS8 package | 2 |
CAD (KiCad official)
- Symbol:
LTC2850IMS8#PBF - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
ltc2850ims8-pbf-etched.step/ltc2850ims8-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc2850ims8-pbf.step/ltc2850ims8-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (18 pp, sha256
68e25e1cc3687b9f, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).