main
Ray
Publish 0.1.0
07893d0
LTC1799CS5#TRPBF
Analog Devices · Timers / Clock Oscillators · TSOT-23-5
LTC1799CS5#TRPBF from Analog Devices, in a TSOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V+ | power_in | Voltage supply input rated 2.7V to 5.5V, which must be kept free from noise and ripple and bypassed directly to a ground plane with a 0.1µF capacitor. |
| 2 | GND | power_in | Ground reference pin that should be tied to a ground plane for best performance. |
| 3 | SET | input | Frequency-setting resistor input where the resistor between SET and V+ sets the oscillator frequency; SET is held about 1.13V below V+, a precision metal film resistor of 10k to 200k is recommended, and capacitance on this pin should be limited to less than 10pF. |
| 4 | DIV | input | Three-state divider-select input that selects ÷1 when tied to GND, ÷10 when floated, and ÷100 when tied to V+, and driving it high or low requires sourcing or sinking about 5µA against the internal midsupply pull. |
| 5 | OUT | output | Oscillator rail-to-rail CMOS square-wave output that can drive 5kΩ and/or 10pF loads, and transients will not cause latchup if the current into or out of the pin is limited to 50mA. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSOT-23-5 |
| Category | Clock and Timing |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating supply range | V+ | 2.7 | 5.5 | V | 3 | ||
| Supply voltage V+ to GND | V+ | -0.3 | 6 | V | 2 | ||
| Operating temperature range, LTC1799C | TA | 0 | 70 | °C | LTC1799C grade | 2 | |
| Storage temperature range | TSTG | -65 | 150 | °C | 2 | ||
| Lead temperature (soldering) | 300 | °C | 10 sec soldering | 2 | |||
| Maximum junction temperature | TJMAX | 150 | °C | 2 | |||
| Thermal resistance junction to ambient | θJA | 256 | °C/W | 2 | |||
| Frequency-setting resistor range | RSET | 5 | 200 | kΩ | /∆f/ < 1.5%, V+ = 5V | 3 | |
| Frequency-setting resistor range | RSET | 10 | 200 | kΩ | /∆f/ < 1.5%, V+ = 3V | 3 | |
| Maximum frequency | fMAX | 33 | MHz | /∆f/ < 2.5%, Pin 4 = 0V, V+ = 5V | 3 | ||
| Maximum frequency | fMAX | 20 | MHz | /∆f/ < 2.5%, Pin 4 = 0V, V+ = 3V | 3 | ||
| Minimum frequency | fMIN | 1 | kHz | /∆f/ < 2.5%, Pin 4 = V+ | 3 | ||
| Frequency drift over temperature | ∆f/∆T | -0.004 | 0.004 | %/°C | RSET = 31.6k | 3 | |
| Frequency drift over supply | ∆f/∆V | 0.05 | 0.1 | %/V | V+ = 3V to 5V, RSET = 31.6k | 3 | |
| Duty cycle | 49 | 50 | 51 | % | Pin 4 = V+ or Open (DIV by 100 or 10) | 3 | |
| Duty cycle | 45 | 50 | 55 | % | Pin 4 = 0V (DIV by 1), RSET = 5k to 200k | 3 | |
| Supply current | IS | 0.7 | 1.1 | mA | RSET = 200k, Pin 4 = V+, RL = ∞, V+ = 5V | 3 | |
| Supply current | IS | 2.4 | mA | RSET = 10k, Pin 4 = 0V, RL = ∞, V+ = 5V | 3 | ||
| Supply current | IS | 2 | mA | RSET = 10k, Pin 4 = 0V, RL = ∞, V+ = 3V | 3 | ||
| Low level DIV input voltage | VIL | 0.5 | V | 3 | |||
| DIV input current | IDIV | -8 | -5 | µA | Pin 4 = V+, V+ = 5V | 3 | |
| DIV input current | IDIV | 5 | 8 | µA | Pin 4 = 0V, V+ = 5V | 3 | |
| High level output voltage | VOH | 4.8 | 4.95 | V | V+ = 5V, IOH = -1mA | 4 | |
| High level output voltage | VOH | 4.5 | 4.8 | V | V+ = 5V, IOH = -4mA | 4 | |
| High level output voltage | VOH | 2.7 | 2.9 | V | V+ = 3V, IOH = -1mA | 4 | |
| High level output voltage | VOH | 2.2 | 2.6 | V | V+ = 3V, IOH = -4mA | 4 | |
| Low level output voltage | VOL | 0.05 | 0.15 | V | V+ = 5V, IOL = 1mA | 4 | |
| Low level output voltage | VOL | 0.2 | 0.4 | V | V+ = 5V, IOL = 4mA | 4 | |
| Low level output voltage | VOL | 0.1 | 0.3 | V | V+ = 3V, IOL = 1mA | 4 | |
| Low level output voltage | VOL | 0.4 | 0.7 | V | V+ = 3V, IOL = 4mA | 4 | |
| Timing jitter | 0.06 | % | Pin 4 = V+ | 3 | |||
| Timing jitter | 0.13 | % | Pin 4 = Open | 3 | |||
| Timing jitter | 0.4 | % | Pin 4 = 0V | 3 | |||
| Long-term stability of output frequency | 300 | ppm/√kHr | 3 | ||||
| OUT rise time | tr | 14 | ns | V+ = 5V, Pin 4 = V+ or Floating, RL = ∞ | 4 | ||
| OUT rise time | tr | 7 | ns | V+ = 5V, Pin 4 = 0V, RL = ∞ | 4 | ||
| OUT rise time | tr | 19 | ns | V+ = 3V, Pin 4 = V+ or Floating, RL = ∞ | 4 | ||
| OUT rise time | tr | 11 | ns | V+ = 3V, Pin 4 = 0V, RL = ∞ | 4 | ||
| OUT fall time | tf | 13 | ns | V+ = 5V, Pin 4 = V+ or Floating, RL = ∞ | 4 | ||
| OUT fall time | tf | 6 | ns | V+ = 5V, Pin 4 = 0V, RL = ∞ | 4 | ||
| OUT fall time | tf | 19 | ns | V+ = 3V, Pin 4 = V+ or Floating, RL = ∞ | 4 | ||
| OUT fall time | tf | 10 | ns | V+ = 3V, Pin 4 = 0V, RL = ∞ | 4 |
CAD (KiCad official)
- Symbol:
LTC1799CS5#TRPBF - Footprint:
Package_TO_SOT_SMD:TSOT-23-5 - 3D model: TSOT-23-5 (KiCad packages3D, STEP)
- 3D model files:
ltc1799cs5-trpbf-etched.step/ltc1799cs5-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ltc1799cs5-trpbf.step/ltc1799cs5-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (14 pp, sha256
ce4553360ca47502, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LTC1799CS5#TRPBF
**Analog Devices** · Timers / Clock Oscillators · TSOT-23-5
LTC1799CS5#TRPBF from Analog Devices, in a TSOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V+ | power_in | Voltage supply input rated 2.7V to 5.5V, which must be kept free from noise and ripple and bypassed directly to a ground plane with a 0.1µF capacitor. |
| 2 | GND | power_in | Ground reference pin that should be tied to a ground plane for best performance. |
| 3 | SET | input | Frequency-setting resistor input where the resistor between SET and V+ sets the oscillator frequency; SET is held about 1.13V below V+, a precision metal film resistor of 10k to 200k is recommended, and capacitance on this pin should be limited to less than 10pF. |
| 4 | DIV | input | Three-state divider-select input that selects ÷1 when tied to GND, ÷10 when floated, and ÷100 when tied to V+, and driving it high or low requires sourcing or sinking about 5µA against the internal midsupply pull. |
| 5 | OUT | output | Oscillator rail-to-rail CMOS square-wave output that can drive 5kΩ and/or 10pF loads, and transients will not cause latchup if the current into or out of the pin is limited to 50mA. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSOT-23-5 |
| Category | Clock and Timing |
| Pins | 5 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating supply range | V+ | 2.7 | | 5.5 | V | | 3 |
| Supply voltage V+ to GND | V+ | -0.3 | | 6 | V | | 2 |
| Operating temperature range, LTC1799C | TA | 0 | | 70 | °C | LTC1799C grade | 2 |
| Storage temperature range | TSTG | -65 | | 150 | °C | | 2 |
| Lead temperature (soldering) | | | | 300 | °C | 10 sec soldering | 2 |
| Maximum junction temperature | TJMAX | | | 150 | °C | | 2 |
| Thermal resistance junction to ambient | θJA | | 256 | | °C/W | | 2 |
| Frequency-setting resistor range | RSET | 5 | | 200 | kΩ | /∆f/ < 1.5%, V+ = 5V | 3 |
| Frequency-setting resistor range | RSET | 10 | | 200 | kΩ | /∆f/ < 1.5%, V+ = 3V | 3 |
| Maximum frequency | fMAX | 33 | | | MHz | /∆f/ < 2.5%, Pin 4 = 0V, V+ = 5V | 3 |
| Maximum frequency | fMAX | 20 | | | MHz | /∆f/ < 2.5%, Pin 4 = 0V, V+ = 3V | 3 |
| Minimum frequency | fMIN | | | 1 | kHz | /∆f/ < 2.5%, Pin 4 = V+ | 3 |
| Frequency drift over temperature | ∆f/∆T | -0.004 | | 0.004 | %/°C | RSET = 31.6k | 3 |
| Frequency drift over supply | ∆f/∆V | | 0.05 | 0.1 | %/V | V+ = 3V to 5V, RSET = 31.6k | 3 |
| Duty cycle | | 49 | 50 | 51 | % | Pin 4 = V+ or Open (DIV by 100 or 10) | 3 |
| Duty cycle | | 45 | 50 | 55 | % | Pin 4 = 0V (DIV by 1), RSET = 5k to 200k | 3 |
| Supply current | IS | | 0.7 | 1.1 | mA | RSET = 200k, Pin 4 = V+, RL = ∞, V+ = 5V | 3 |
| Supply current | IS | | | 2.4 | mA | RSET = 10k, Pin 4 = 0V, RL = ∞, V+ = 5V | 3 |
| Supply current | IS | | | 2 | mA | RSET = 10k, Pin 4 = 0V, RL = ∞, V+ = 3V | 3 |
| Low level DIV input voltage | VIL | | | 0.5 | V | | 3 |
| DIV input current | IDIV | -8 | | -5 | µA | Pin 4 = V+, V+ = 5V | 3 |
| DIV input current | IDIV | 5 | | 8 | µA | Pin 4 = 0V, V+ = 5V | 3 |
| High level output voltage | VOH | 4.8 | | 4.95 | V | V+ = 5V, IOH = -1mA | 4 |
| High level output voltage | VOH | 4.5 | | 4.8 | V | V+ = 5V, IOH = -4mA | 4 |
| High level output voltage | VOH | 2.7 | | 2.9 | V | V+ = 3V, IOH = -1mA | 4 |
| High level output voltage | VOH | 2.2 | | 2.6 | V | V+ = 3V, IOH = -4mA | 4 |
| Low level output voltage | VOL | | 0.05 | 0.15 | V | V+ = 5V, IOL = 1mA | 4 |
| Low level output voltage | VOL | | 0.2 | 0.4 | V | V+ = 5V, IOL = 4mA | 4 |
| Low level output voltage | VOL | | 0.1 | 0.3 | V | V+ = 3V, IOL = 1mA | 4 |
| Low level output voltage | VOL | | 0.4 | 0.7 | V | V+ = 3V, IOL = 4mA | 4 |
| Timing jitter | | | 0.06 | | % | Pin 4 = V+ | 3 |
| Timing jitter | | | 0.13 | | % | Pin 4 = Open | 3 |
| Timing jitter | | | 0.4 | | % | Pin 4 = 0V | 3 |
| Long-term stability of output frequency | | | 300 | | ppm/√kHr | | 3 |
| OUT rise time | tr | | 14 | | ns | V+ = 5V, Pin 4 = V+ or Floating, RL = ∞ | 4 |
| OUT rise time | tr | | 7 | | ns | V+ = 5V, Pin 4 = 0V, RL = ∞ | 4 |
| OUT rise time | tr | | 19 | | ns | V+ = 3V, Pin 4 = V+ or Floating, RL = ∞ | 4 |
| OUT rise time | tr | | 11 | | ns | V+ = 3V, Pin 4 = 0V, RL = ∞ | 4 |
| OUT fall time | tf | | 13 | | ns | V+ = 5V, Pin 4 = V+ or Floating, RL = ∞ | 4 |
| OUT fall time | tf | | 6 | | ns | V+ = 5V, Pin 4 = 0V, RL = ∞ | 4 |
| OUT fall time | tf | | 19 | | ns | V+ = 3V, Pin 4 = V+ or Floating, RL = ∞ | 4 |
| OUT fall time | tf | | 10 | | ns | V+ = 3V, Pin 4 = 0V, RL = ∞ | 4 |
## CAD (KiCad official)
- Symbol: `LTC1799CS5#TRPBF`
- Footprint: `Package_TO_SOT_SMD:TSOT-23-5`
- 3D model: TSOT-23-5 (KiCad packages3D, STEP)
- 3D model files: `ltc1799cs5-trpbf-etched.step` / `ltc1799cs5-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ltc1799cs5-trpbf.step` / `ltc1799cs5-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/LTC1799.pdf) (14 pp, sha256 `ce4553360ca47502`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ltc1799cs5-trpbf-datasheet.pdf)