main
Ray Publish 0.1.0 17a4952

LT8619EMSE-5#PBF

Analog Devices · DC-DC Converters · MSOP-16-EP

LT8619EMSE-5#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No connect; this pin is not connected to the internal circuitry.
2 VIN power_in Supplies current to the internal circuitry and the internal top-side power switch, and the input bypass capacitor should be placed as close as possible to this pin and the GND pin; the datasheet gives a 3.0V minimum input voltage and a 60V absolute maximum for VIN.
3 NC unconnected No connect; this pin is not connected to the internal circuitry.
4 EN/UV input Active-high enable with a 1V power-on threshold; forcing it below 0.56V puts the IC into low-current shutdown, a resistor divider from VIN can program VIN undervoltage lockout, and the absolute maximum rating is 60V.
5 RT passive A resistor from this pin to ground sets the switching frequency, and the resistor must be chosen so the frequency is at or below the synchronization frequency when synchronizing; do not apply an external voltage to this pin.
6 PG output Open-drain power good output that stays low until the FB pin is within ±7.5% of the final regulation voltage, with a pull-up to INTVCC, VOUT, or an external supply lower than 6V (absolute maximum 6V).
7 SYNC input External clock synchronization input: tie to a clock for forced continuous mode synchronization, ground for Burst Mode operation, connect to INTVCC for forced continuous mode, or float for pulse-skipping mode; the absolute maximum rating is 6V.
8 GND power_in Ground; connect to the negative terminal of the input capacitor and solder to the PCB to lower thermal resistance.
9 OUT input On the LT8619-5 this pin connects to the regulator output VOUT and to the internal 10MΩ feedback divider that sets the fixed 5V output.
10 OUT input On the LT8619-5 this pin connects to the regulator output VOUT and to the internal 10MΩ feedback divider that sets the fixed 5V output.
11 BIAS power_in When tied above 3.1V the internal regulator draws current from BIAS instead of VIN; for outputs of 3.3V and above it should be tied to VOUT, and the absolute maximum rating is 30V.
12 INTVCC power_out Internal 3.3V regulator output that powers the internal drivers and control circuits, with a maximum external load of 20mA, requires at least 1µF low ESR decoupling to GND, and must not be loaded with external circuitry.
13 NC unconnected No connect; this pin is not connected to the internal circuitry.
14 BST passive Provides a drive voltage above the input voltage to the top-side power switch through a 0.1µF boost capacitor placed as close as possible to the IC, with BST above SW rated at 4V absolute maximum.
15 SW output Output of the internal power switches that connects to the inductor and boost capacitor; this node should be kept small on the PCB for good performance.
16 SW output Output of the internal power switches that connects to the inductor and boost capacitor; this node should be kept small on the PCB for good performance.
17 GND power_in Exposed pad is ground and must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Regulated Output Voltage (LT8619-5), 25°C 4.975 5 5.025 V LT8619-5, VIN = 12V, VSYNC = INTVCC, No Load, TA = 25°C 3
Regulated Output Voltage (LT8619-5), full operating temperature range 4.925 5 5.075 V LT8619-5, VIN = 12V, VSYNC = INTVCC, No Load, l (full operating temperature range) 3
VIN Quiescent Current at No Load, 25°C 0.6 1 µA VIN = 12V, VEN/UV = 0V 3
VIN Quiescent Current at No Load, full operating temperature range 0.6 3 µA VIN = 12V, VEN/UV = 0V, l (full operating temperature range) 3
VIN Quiescent Current (Burst Mode, no load), 25°C 6 10 µA VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V 3
VIN Quiescent Current (Burst Mode, no load), full operating temperature range 6 18 µA VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V, l (full operating temperature range) 3
VIN Current in Regulation at ILOAD = 100µA 38 65 µA VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V, ILOAD = 100µA, l (full operating temperature range) 3
VIN Current in Regulation at ILOAD = 1mA 320 400 µA VIN = 12V, VOUT = 3.3V, RT = 66.5k, BIAS = VOUT, VSYNC = 0V, ILOAD = 1mA, l (full operating temperature range) 3
Feedback Voltage Line Regulation (LT8619-5) -0.03 0.004 0.03 %/V LT8619-5, VIN = 6V to 50V, VSYNC = INTVCC, Note 5 (guaranteed by design, not subject to test) 3
Minimum Off-Time 100 150 180 ns 3
Top Switch Peak Current Limit 1.5 1.75 2 A l (full operating temperature range) 3
Operating Frequency, RT = 162k 260 300 340 kHz RT = 162k, l (full operating temperature range) 3
Operating Frequency, RT = 66.5k 630 700 770 kHz RT = 66.5k, l (full operating temperature range) 3
Operating Frequency, RT = 20k 1.9 2 2.1 MHz RT = 20k, l (full operating temperature range) 3
Synchronization Frequency fSYNC 0.3 2.2 MHz fSYNC ≥ fOSC, l (full operating temperature range) 3
EN/UV Power-On Threshold 0.94 1 1.1 V EN/UV rising, l (full operating temperature range) 4
EN/UV Shutdown Threshold 0.34 0.56 0.92 V EN/UV falling, l (full operating temperature range) 4
EN/UV Pin Current -100 100 nA VEN/UV = 2V 4
Positive Power Good Threshold 5 7.5 10 % VFB/VOUT rising wrt. regulated VFB/VOUT, l (full operating temperature range) 4
Negative Power Good Threshold -5 -7.5 -10 % VFB/VOUT rising wrt. regulated VFB/VOUT, l (full operating temperature range) 4
PG Leakage -100 100 nA VPG = 3.3V, Power Good 4
PG VOL 0.01 0.3 V IPG = 100µA, l (full operating temperature range) 4
VIN Minimum Input Voltage 3 V 3
VIN, EN/UV (Absolute Maximum) VIN, EN/UV 60 V 2
BIAS (Absolute Maximum) BIAS 30 V 2
BST Pin Above SW Pin (Absolute Maximum) 4 V BST pin above SW pin 2
PG, SYNC, OUT (Absolute Maximum) PG, SYNC, OUT 6 V 2
Storage Temperature Range -65 150 °C 2
Operating Junction Temperature (LT8619E-5) -40 125 °C LT8619E-5 (E grade, MSE package) 2
Thermal Resistance Junction-to-Ambient, θJA θJA 40 °C/W MSE package (16-lead plastic MSOP) 2
Thermal Resistance Junction-to-Case, θJC θJC 10 °C/W MSE package (16-lead plastic MSOP) 2

CAD (KiCad official)

  • Symbol: LT8619EMSE-5#PBF
  • Footprint: Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm
  • 3D model: MSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lt8619emse-5-pbf-etched.step / lt8619emse-5-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8619emse-5-pbf.step / lt8619emse-5-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (28 pp, sha256 7156fb4077c7704f, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF