3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT8610AIMSE#PBF
Analog Devices · DC-DC Converters · MSOP-16-EP
LT8610AIMSE#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SYNC | input | External clock synchronization input; ground for low ripple Burst Mode operation, tie to a clock source to synchronize, or apply 3V or higher / tie to INTVCC for pulse-skipping mode; do not float. |
| 2 | TR/SS | input | Output tracking and soft-start pin; FB regulates to TR/SS voltage below 0.97V, internal 2.2µA pull-up from INTVCC sets ramp with a capacitor, pulled to ground by 230Ω MOSFET in shutdown and fault, may be left floating. |
| 3 | RT | passive | A resistor tied between RT and ground sets the switching frequency (200kHz to 2.2MHz). |
| 4 | EN/UV | input | Shuts down the part when low and is active when high, with a hysteretic threshold of 1.00V rising and 0.96V falling; tie to VIN if unused, or use a resistor divider from VIN to program a VIN undervoltage threshold. |
| 5 | VIN | power_in | Supplies current to internal circuitry and the topside power switch (3.4V to 42V operation); must be tied to pin 6 and locally bypassed. |
| 6 | VIN | power_in | Supplies current to internal circuitry and the topside power switch; must be tied to pin 5 and locally bypassed. |
| 7 | NC | unconnected | No connect; this pin is not connected to internal circuitry. |
| 8 | GND | power_in | Ground, return path of the internal bottom-side switch; must be tied to the exposed pad. |
| 9 | SW | power_out | Output of the internal power switches; tie to pins 10 and 11 and connect to the inductor and boost capacitor, keeping the node small on the PCB. |
| 10 | SW | power_out | Output of the internal power switches; tie to pins 9 and 11 and connect to the inductor and boost capacitor. |
| 11 | SW | power_out | Output of the internal power switches; tie to pins 9 and 10 and connect to the inductor and boost capacitor. |
| 12 | BST | passive | Provides drive voltage higher than the input voltage to the topside power switch; place a 0.1µF boost capacitor close to the IC (max 4V above SW). |
| 13 | INTVCC | power_out | Internal 3.4V regulator bypass pin, maximum output current 20mA, do not load externally; decouple to ground with at least a 1µF low ESR ceramic capacitor. |
| 14 | BIAS | power_in | Internal regulator draws current from BIAS instead of VIN when tied above 3.1V; tie to VOUT for outputs of 3.3V and above, or use a 1µF local bypass capacitor if tied to another supply (30V max). |
| 15 | PG | output | Open-drain output of an internal comparator that stays low until FB is within ±9% of final regulation and no faults exist; valid when VIN is above 3.4V regardless of EN/UV state. |
| 16 | FB | input | Feedback pin regulated to 0.970V; connect the feedback resistor divider tap here and a 4.7pF to 10pF phase lead capacitor between FB and VOUT. |
| 17 | GND | power_in | Exposed pad, ground; must be tied to GND pin 8 and soldered to the PCB to lower thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | VIN(MIN) | 2.9 | 3.4 | V | full temperature range | 3 | |
| VIN Quiescent Current | IQ | 1 | 3 | µA | VEN/UV = 0V | 3 | |
| VIN Quiescent Current (not switching) | IQ | 1.7 | 4 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V | 3 | |
| VIN Quiescent Current (SYNC high) | IQ | 0.26 | 0.5 | mA | VEN/UV = 2V, Not Switching, VSYNC = 2V | 3 | |
| VIN Current in Regulation | 24 | 50 | µA | VOUT = 0.97V, VIN = 6V, Output Load = 100µA (LT8610A) | 3 | ||
| VIN Current in Regulation | 210 | 350 | µA | VOUT = 0.97V, VIN = 6V, Output Load = 1mA (LT8610A) | 3 | ||
| Feedback Reference Voltage | VFB | 0.964 | 0.97 | 0.976 | V | VIN = 6V, ILOAD = 0.5A | 3 |
| Feedback Reference Voltage (full temp) | VFB | 0.958 | 0.97 | 0.982 | V | VIN = 6V, ILOAD = 0.5A, full temperature range | 3 |
| Feedback Voltage Line Regulation | 0.004 | 0.02 | %/V | VIN = 4V to 42V, ILOAD = 1A | 3 | ||
| Feedback Pin Input Current | -20 | 20 | nA | VFB = 1V | 3 | ||
| INTVCC Voltage | 3.23 | 3.4 | 3.57 | V | ILOAD = 0mA, VBIAS = 0V | 4 | |
| INTVCC Voltage | 3.25 | 3.29 | 3.35 | V | ILOAD = 0mA, VBIAS = 3.3V | 4 | |
| INTVCC Undervoltage Lockout | 2.5 | 2.6 | 2.7 | V | 4 | ||
| BIAS Pin Current Consumption | 9 | mA | VBIAS = 3.3V, ILOAD = 1A, 2MHz | 4 | |||
| Minimum On-Time | tON(MIN) | 15 | 30 | 45 | ns | ILOAD = 1A, SYNC = 0V | 4 |
| Minimum Off-Time | tOFF(MIN) | 95 | 125 | ns | 4 | ||
| Oscillator Frequency | fSW | 180 | 210 | 240 | kHz | RT = 221k, ILOAD = 1A | 4 |
| Oscillator Frequency | fSW | 665 | 700 | 735 | kHz | RT = 60.4k, ILOAD = 1A | 4 |
| Oscillator Frequency | fSW | 1.85 | 2 | 2.15 | MHz | RT = 18.2k, ILOAD = 1A | 4 |
| Top Power NMOS On-Resistance | 120 | mΩ | ISW = 1A | 4 | |||
| Top Power NMOS Current Limit | 5 | 6.7 | 8 | A | LT8610A | 4 | |
| Bottom Power NMOS On-Resistance | 65 | mΩ | VINTVCC = 3.4V, ISW = 1A | 4 | |||
| Bottom Power NMOS Current Limit | 3.4 | 4.3 | 5.4 | A | VINTVCC = 3.4V | 4 | |
| SW Leakage Current | -1.5 | 1.5 | µA | VIN = 42V, VSW = 0V, 42V | 4 | ||
| EN/UV Pin Threshold | 0.94 | 1 | 1.06 | V | EN/UV Rising | 4 | |
| EN/UV Pin Hysteresis | 40 | mV | 4 | ||||
| EN/UV Pin Current | -20 | 20 | nA | VEN/UV = 2V | 4 | ||
| PG Upper Threshold Offset from VFB | 6 | 9 | 12 | % | VFB Falling | 4 | |
| PG Lower Threshold Offset from VFB | -12 | -9 | -6 | % | VFB Rising | 4 | |
| PG Hysteresis | 1.3 | % | 4 | ||||
| PG Leakage | -40 | 40 | nA | VPG = 3.3V | 4 | ||
| PG Pull-Down Resistance | 680 | 2000 | Ω | VPG = 0.1V | 4 | ||
| SYNC Threshold Falling | 0.8 | 1.1 | 1.4 | V | SYNC Falling | 4 | |
| SYNC Threshold Rising | 1.6 | 2 | 2.4 | V | SYNC Rising | 4 | |
| SYNC Pin Current | -40 | 40 | nA | VSYNC = 6V | 4 | ||
| TR/SS Source Current | 1 | 2 | 3.2 | µA | 4 | ||
| TR/SS Pull-Down Resistance | 230 | Ω | Fault Condition, TR/SS = 0.1V | 4 | |||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | LT8610AI (Note 2) | 2 | |
| VIN, EN/UV, PG Voltage | 42 | V | 2 | ||||
| BST Pin Above SW Pin | 4 | V | 2 | ||||
| FB, TR/SS, RT, INTVCC Voltage | 4 | V | 2 | ||||
| VOUT, SYNC Voltage | 6 | V | 2 | ||||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Thermal Resistance Junction-Ambient | θJA | 40 | °C/W | MSE package | 2 | ||
| Thermal Resistance Junction-Case (pad) | θJC(PAD) | 10 | °C/W | MSE package | 2 |
CAD (KiCad official)
- Symbol:
LT8610AIMSE#PBF - Footprint:
Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm - 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lt8610aimse-pbf-etched.step/lt8610aimse-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8610aimse-pbf.step/lt8610aimse-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (26 pp, sha256
b37433c4b3415525, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).