main
Ray Publish 0.1.0 6cc01f8

LT8610ABEMSE-5#TRPBF

Analog Devices · DC-DC Converters · MSOP-16-EP

LT8610ABEMSE-5#TRPBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SYNC input External clock synchronization input that must be grounded for low-ripple Burst Mode at low loads, must receive a DC voltage of 3V or higher or be tied to INTVCC for pulse-skipping mode, and must not be left floating.
2 TR/SS passive Output tracking and soft-start pin where a voltage below 0.97V forces FB to follow it, an internal 2.2µA pull-up from INTVCC sets the capacitor-programmed ramp rate, and an internal 230Ω pull-down is active in shutdown and fault conditions.
3 RT passive A resistor tied between RT and ground sets the switching frequency.
4 EN/UV input Enable and undervoltage input that shuts the device down when low, with a hysteretic threshold of 1.00V rising and 0.96V falling, and an external resistor divider from VIN can set the VIN shutdown threshold.
5 VIN power_in Input supply pin for the internal circuitry and top power switch that must be tied together with pin 6 and locally bypassed.
6 VIN power_in Input supply pin for the internal circuitry and top power switch that must be tied together with pin 5 and locally bypassed.
7 NC unconnected No connect pin that is not connected to internal circuitry.
8 GND power_in Ground return for the internal bottom-side switch that must be tied together with the other GND connections and the exposed pad.
9 SW output Output of the internal power switches that must be tied together with pins 10 and 11 and connected to the inductor and boost capacitor with a small PCB node.
10 SW output Output of the internal power switches that must be tied together with pins 9 and 11 and connected to the inductor and boost capacitor with a small PCB node.
11 SW output Output of the internal power switches that must be tied together with pins 9 and 10 and connected to the inductor and boost capacitor with a small PCB node.
12 BST passive Provides a drive voltage higher than the input voltage to the top power switch and requires a 0.1µF boost capacitor placed as close as possible to the IC.
13 INTVCC power_out Internal 3.4V regulator bypass pin with a maximum output current of 20mA that must not be loaded externally and needs at least a 1µF low-ESR ceramic decoupling capacitor.
14 BIAS power_in Supply input for the internal regulator that draws current from BIAS when tied above 3.1V, and should be tied to VOUT for outputs of 3.3V and above or bypassed with 1µF if tied to another supply.
15 PG output Open-drain power-good output that remains low until FB is within ±9% of the regulation voltage with no fault conditions, and is valid when VIN is above 3.4V.
16 VOUT input Output voltage sense pin for the LT8610A-5/LT8610AB-5 fixed 5V version that connects to a 12.5MΩ internal feedback divider, regulating VOUT to 5V.
17 GND power_in Exposed pad ground that must be soldered to the PCB to lower thermal resistance and is the return path for the GND pins.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output Voltage (LT8610A-5/LT8610AB-5) VOUT 4.97 5 5.03 V VIN = 8V, ILOAD = 0.5A 3
Output Voltage (LT8610A-5/LT8610AB-5), full temperature range VOUT 4.94 5 5.06 V VIN = 8V, ILOAD = 0.5A, full operating temperature range 3
Voltage Line Regulation (LT8610A-5/LT8610AB-5) 0.004 0.02 %/V VIN = 6V to 42V, ILOAD = 1A 3
Minimum Input Voltage 2.9 3.4 V Full operating temperature range (l); Note 4 3
VIN Quiescent Current IQ 1 3 µA VEN/UV = 0V 3
VIN Quiescent Current, full temperature range IQ 1 8 µA VEN/UV = 0V, full operating temperature range 3
VIN Quiescent Current IQ 1.7 4 µA VEN/UV = 2V, Not Switching, VSYNC = 0V 3
VIN Quiescent Current, full temperature range IQ 1.7 10 µA VEN/UV = 2V, Not Switching, VSYNC = 0V, full operating temperature range 3
VIN Quiescent Current IQ 0.26 0.5 mA VEN/UV = 2V, Not Switching, VSYNC = 2V 3
VIN Current in Regulation (LT8610AB-5) 180 1200 µA VOUT = 5V, VIN = 8V, Output Load = 100µA 3
VIN Current in Regulation (LT8610AB-5) 150 1100 µA VOUT = 5V, VIN = 8V, Output Load = 1mA 3
Internal Feedback Resistor Divider (LT8610AB-5) 12.5 MΩ 4
INTVCC Voltage INTVCC 3.23 3.25 3.4 V ILOAD = 0mA, VBIAS = 0V 4
INTVCC Undervoltage Lockout INTVCC 2.5 2.6 2.7 V 4
Minimum On-Time 15 30 45 ns ILOAD = 1A, SYNC = 0V 4
Minimum Off-Time 95 125 ns 4
Oscillator Frequency fSW 180 210 240 kHz RT = 221k, ILOAD = 1A 4
Oscillator Frequency fSW 665 700 735 kHz RT = 60.4k, ILOAD = 1A 4
Oscillator Frequency fSW 1.85 2 2.15 MHz RT = 18.2k, ILOAD = 1A 4
Top Power NMOS Current Limit (LT8610AB) 5 6.7 8 A 4
Bottom Power NMOS Current Limit 3.4 4.3 5.4 A VINTVCC = 3.4V 4
SW Leakage Current -1.5 1.5 µA VIN = 42V, VSW = 0V, 42V 4
EN/UV Pin Threshold 0.94 1 1.06 V EN/UV Rising 4
EN/UV Pin Current -20 20 nA VEN/UV = 2V 4
PG Upper Threshold Offset from VFB 6 9 12 % VFB Falling 4
PG Lower Threshold Offset from VFB -12 -9 -6 % VFB Rising 4
PG Leakage -40 40 nA VPG = 3.3V 4
PG Pull-Down Resistance 680 2000 Ω VPG = 0.1V 4
SYNC Threshold (SYNC Falling) 0.8 1.1 1.4 V SYNC Falling 4
SYNC Threshold (SYNC Rising) 1.6 2 2.4 V SYNC Rising 4
SYNC Pin Current -40 40 nA VSYNC = 6V 4
TR/SS Source Current 1 2 3.2 µA 4
Operating Junction Temperature Range (LT8610ABE) TJ -40 125 °C LT8610ABE grade 2
VIN, EN/UV, PG voltage VIN, EN/UV, PG 42 V 2
BST Pin Above SW Pin BST-SW 4 V 2
FB, TR/SS, RT, INTVCC voltage FB, TR/SS, RT, INTVCC 4 V 2
VOUT, SYNC voltage VOUT, SYNC 6 V 2
Storage Temperature Range TSTG -65 150 °C 2
Thermal Resistance Junction-to-Ambient θJA 40 °C/W 16-lead plastic MSOP 2
Thermal Resistance Junction-to-Case (Pad) θJC(PAD) 10 °C/W 16-lead plastic MSOP 2

CAD (KiCad official)

  • Symbol: LT8610ABEMSE-5#TRPBF
  • Footprint: Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm
  • 3D model: MSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lt8610abemse-5-trpbf-etched.step / lt8610abemse-5-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8610abemse-5-trpbf.step / lt8610abemse-5-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (26 pp, sha256 b37433c4b3415525, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF