main
Ray Publish 0.1.0 5b18756

LT8610ABEMSE-3.3#PBF

Analog Devices · DC-DC Converters · MSOP-16-EP

LT8610ABEMSE-3.3#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SYNC input External clock synchronization input that must not float; ground it for low-ripple Burst Mode, apply a DC voltage of 3V or higher or tie it to INTVCC for pulse-skipping mode.
2 TR/SS bidirectional Output tracking and soft-start pin where a voltage below 0.97V forces FB to follow it, and an internal 2.2µA pull-up from INTVCC sets the output voltage slew rate through an external capacitor.
3 RT passive A resistor tied between RT and ground sets the switching frequency.
4 EN/UV input Enable and undervoltage pin that shuts the regulator down when low, with a hysteretic threshold of 1.00V rising and 0.96V falling, and is tied to VIN if the shutdown feature is not used.
5 VIN power_in Input supply pin that powers the internal circuitry and top-side power switch; it must be tied together with pin 6 and locally bypassed.
6 VIN power_in Input supply pin that powers the internal circuitry and top-side power switch; it must be tied together with pin 5 and locally bypassed.
7 NC unconnected No connect pin that is not connected to internal circuitry.
8 GND power_in Ground return for the internal bottom-side switch that must be tied together with the other ground pins and the exposed pad.
9 SW output Output of the internal power switches that must be tied together with pins 10 and 11 and connected to the inductor and boost capacitor with a small PCB node.
10 SW output Output of the internal power switches that must be tied together with pins 9 and 11 and connected to the inductor and boost capacitor with a small PCB node.
11 SW output Output of the internal power switches that must be tied together with pins 9 and 10 and connected to the inductor and boost capacitor with a small PCB node.
12 BST passive Provides a drive voltage higher than the input voltage to the top-side power switch and requires a 0.1µF boost capacitor placed as close to the IC as possible.
13 INTVCC power_out Internal 3.4V regulator bypass pin with a maximum output current of 20mA that must not be loaded externally and needs at least 1µF low ESR ceramic decoupling.
14 BIAS power_in Supplies the internal regulator from BIAS instead of VIN when tied above 3.1V, and for output voltages of 3.3V and above it should be tied to VOUT.
15 PG output Open-drain power-good output that remains low until FB is within ±9% of the final regulation voltage with no fault conditions, and is valid when VIN is above 3.4V.
16 VOUT input Output voltage sense pin for the fixed-output versions that regulates to 3.3V through a 14.3MΩ internal feedback divider for the -3.3 variant.
17 GND power_in Exposed pad ground that must be soldered to the PCB to lower the thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Output Voltage (LT8610AB-3.3) VOUT 3.28 3.3 3.32 V VIN = 8V, ILOAD = 0.5A, 25C 3
Output Voltage (LT8610AB-3.3) full temp VOUT 3.26 3.3 3.34 V VIN = 8V, ILOAD = 0.5A, full operating temperature range 3
Minimum Input Voltage VIN 2.9 3.4 V Note 4 3
VIN Quiescent Current, VEN/UV = 0V IQ 1 3 µA VEN/UV = 0V 3
VIN Quiescent Current, VEN/UV = 0V full temp IQ 1 8 µA VEN/UV = 0V, full temperature range 3
VIN Quiescent Current, not switching, VSYNC = 0V IQ 1.7 4 µA VEN/UV = 2V, Not Switching, VSYNC = 0V 3
VIN Quiescent Current, not switching, VSYNC = 0V full temp IQ 1.7 10 µA VEN/UV = 2V, Not Switching, VSYNC = 0V, full temperature range 3
VIN Quiescent Current, VSYNC = 2V IQ 0.26 0.5 mA VEN/UV = 2V, Not Switching, VSYNC = 2V 3
VIN Current in Regulation, 100µA load (LT8610AB-3.3) 55 100 µA VOUT = 3.3V, VIN = 8V, Output Load = 100µA (LT8610AB-3.3) 3
VIN Current in Regulation, 1mA load (LT8610AB-3.3) 500 800 µA VOUT = 3.3V, VIN = 8V, Output Load = 1mA (LT8610AB-3.3) 3
Voltage Line Regulation (LT8610AB-3.3) 0.004 0.02 %/V VIN = 4V to 42V, ILOAD = 1A 3
Internal Feedback Resistor Divider (3.3V) 14.3 MΩ 4
INTVCC Voltage, VBIAS = 0V 3.23 3.4 3.57 V ILOAD = 0mA, VBIAS = 0V 4
INTVCC Voltage, VBIAS = 3.3V 3.25 3.29 3.35 V ILOAD = 0mA, VBIAS = 3.3V 4
INTVCC Undervoltage Lockout 2.5 2.6 2.7 V 4
BIAS Pin Current Consumption 9 mA VBIAS = 3.3V, ILOAD = 1A, 2MHz 4
Minimum On-Time, SYNC = 0V tON(MIN) 15 30 45 ns ILOAD = 1A, SYNC = 0V 4
Minimum On-Time, SYNC = 3.3V tON(MIN) 15 30 45 ns ILOAD = 1A, SYNC = 3.3V 4
Minimum Off-Time tOFF(MIN) 95 125 ns 4
Oscillator Frequency, RT = 221k fSW 180 210 240 kHz RT = 221k, ILOAD = 1A 4
Oscillator Frequency, RT = 60.4k fSW 665 700 735 kHz RT = 60.4k, ILOAD = 1A 4
Oscillator Frequency, RT = 18.2k fSW 1.85 2 2.15 MHz RT = 18.2k, ILOAD = 1A 4
Top Power NMOS On-Resistance 120 mΩ ISW = 1A 4
Top Power NMOS Current Limit (LT8610AB) ILIM 5 6.7 8 A LT8610AB 4
Bottom Power NMOS On-Resistance 65 mΩ VINTVCC = 3.4V, ISW = 1A 4
Bottom Power NMOS Current Limit 3.4 4.3 5.4 A VINTVCC = 3.4V 4
SW Leakage Current -1.5 1.5 µA VIN = 42V, VSW = 0V, 42V 4
EN/UV Pin Threshold 0.94 1 1.06 V EN/UV Rising 4
EN/UV Pin Hysteresis 40 mV 4
EN/UV Pin Current -20 20 nA VEN/UV = 2V 4
PG Upper Threshold Offset from VFB 6 9 12 % VFB Falling 4
PG Lower Threshold Offset from VFB -12 -9 -6 % VFB Rising 4
PG Hysteresis 1.3 % 4
PG Leakage -40 40 nA VPG = 3.3V 4
PG Pull-Down Resistance 680 2000 Ω VPG = 0.1V 4
SYNC Threshold Falling 0.8 1.1 1.4 V SYNC Falling 4
SYNC Threshold Rising 1.6 2 2.4 V SYNC Rising 4
SYNC Pin Current -40 40 nA VSYNC = 6V 4
TR/SS Source Current 1 2 3.2 µA 4
TR/SS Pull-Down Resistance 230 Ω Fault Condition, TR/SS = 0.1V 4
Maximum VIN, EN/UV, PG 42 V 2
BST Pin Above SW Pin 4 V 2
FB, TR/SS, RT, INTVCC 4 V 2
VOUT, SYNC Voltage 6 V 2
Operating Junction Temperature Range (LT8610ABE) TJ -40 125 °C Note 2 2
Storage Temperature Range TSTG -65 150 °C 2
Thermal Resistance Junction-Ambient θJA 40 °C/W MSE package 2
Thermal Resistance Junction-Case (Pad) θJC(PAD) 10 °C/W MSE package 2

CAD (KiCad official)

  • Symbol: LT8610ABEMSE-3.3#PBF
  • Footprint: Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm
  • 3D model: MSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lt8610abemse-3-3-pbf-etched.step / lt8610abemse-3-3-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8610abemse-3-3-pbf.step / lt8610abemse-3-3-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (26 pp, sha256 b37433c4b3415525, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF