main
Ray Publish 0.1.0 18cd16c

LT8609IMSE#PBF

Analog Devices · DC-DC Converters · MSOP-10-EP

LT8609IMSE#PBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BST power_out Provides a drive voltage higher than the input voltage to the topside power switch, so a 0.1µF boost capacitor must be placed as close as possible to the IC and no resistor may be placed in series with this pin.
2 SW power_out Output of the internal power switches that connects to the inductor and boost capacitor, and this node should be kept small on the PCB for good performance.
3 INTVCC power_out Internal 3.5V regulator bypass pin with a maximum output current of 20mA that varies between 2.8V and 3.5V, to be decoupled to power ground with at least a 1µF low ESR ceramic capacitor and not loaded with external circuitry.
4 RT passive A resistor tied between RT and ground sets the switching frequency.
5 SYNC input External clock synchronization input that is grounded for low-ripple Burst Mode operation at low output loads, tied to a clock source to synchronize, left floating for pulse-skipping mode without spread spectrum, or tied to INTVCC or a voltage between 3.2V and 5.0V for pulse-skipping mode with spread spectrum modulation.
6 FB input Feedback pin of the adjustable output parts that the device regulates to 0.782V, with the feedback resistor divider tap connected to this pin.
7 TR/SS input Output tracking and soft-start pin where a voltage below 0.782V forces FB to follow the TR/SS voltage and an internal 2µA pull-up from INTVCC sets the output ramp rate, and it is pulled to ground through a 300Ω MOSFET during shutdown and fault conditions.
8 PG output Open-drain power good output that stays low until FB is within ±8.5% of the final regulation voltage with no fault conditions, and is valid when VIN is above 3.2V regardless of the EN/UV state.
9 VIN power_in Supplies current to the internal circuitry and the internal topside power switch, has an absolute maximum rating of 42V, and must be locally bypassed with the input capacitor positive terminal placed as close as possible to the VIN pins.
10 EN/UV input Shutdown pin that disables the part when low and enables it when high, with a hysteretic threshold of 1.05V rising and 1.00V falling, and it should be tied to VIN if the shutdown feature is not used.
11 GND power_in Exposed pad that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower the thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-10-EP
Category Power Management
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Input Voltage 2.7 3 3.2 V full temp range (l) 4
VIN Quiescent Current (LT8609/LT8609A), VEN/UV = 0V, VSYNC = 0V 1 4 µA VEN/UV = 0V, VSYNC = 0V 4
VIN Quiescent Current (LT8609/LT8609A), VEN/UV = 2V, Not Switching, VSYNC = 0V 1.7 12 µA VEN/UV = 2V, Not Switching, VSYNC = 0V, full temp range (l) 4
VIN Current in Regulation (LT8609/LT8609A), 100µA load 46 90 µA VIN = 6V, VOUT = 2.7V, Output Load = 100µA, full temp range (l) 4
VIN Current in Regulation (LT8609/LT8609A), 1mA load 480 700 µA VIN = 6V, VOUT = 2.7V, Output Load = 1mA, full temp range (l) 4
Feedback Reference Voltage (LT8609/LT8609A E/I/H-Grade), 25°C row 0.778 0.782 0.786 V VIN = 6V, ILOAD = 100mA 4
Feedback Reference Voltage (LT8609/LT8609A E/I/H-Grade), full temp range 0.77 0.782 0.794 V VIN = 6V, ILOAD = 100mA, full temp range (l) 4
Feedback Voltage Line Regulation (LT8609/LT8609A) 0.004 0.02 %/V VIN = 4.0V to 40V, full temp range (l) 4
Feedback Pin Input Current -20 20 nA VFB = 1.0V, full temp range (l) 4
Minimum On-Time, SYNC = 0V 45 75 ns ILOAD = 1.5A, SYNC = 0V, full temp range (l) 4
Minimum On-Time, SYNC = 1.9V 45 60 ns ILOAD = 1.5A, SYNC = 1.9V, full temp range (l) 4
Minimum Off Time 90 130 ns 4
Oscillator Frequency (LT8609/LT8609A), RT = 221k 155 200 245 kHz RT = 221k, ILOAD = 0.5A, full temp range (l) 5
Oscillator Frequency (LT8609/LT8609A), RT = 60.4k 640 700 760 kHz RT = 60.4k, ILOAD = 0.5A, full temp range (l) 5
Oscillator Frequency (LT8609/LT8609A), RT = 18.2k 1.925 2 2.075 MHz RT = 18.2k, ILOAD = 0.5A, full temp range (l) 5
Top Power NMOS Current Limit 3.4 4.5 5.7 A full temp range (l) 5
EN/UV Pin Threshold, EN/UV Rising 0.99 1.05 1.11 V EN/UV Rising, full temp range (l) 5
EN/UV Pin Current (LT8609/LT8609A) -20 20 nA VEN/UV = 2V, full temp range (l) 5
PG Upper Threshold Offset from VFB (LT8609/LT8609A) 5 8.5 13 % VFB Rising, full temp range (l) 5
PG Lower Threshold Offset from VFB (LT8609/LT8609A) 5 8.5 13 % VFB Falling, full temp range (l) 5
PG Leakage -200 200 nA VPG = 42V, full temp range (l) 5
PG Pull-Down Resistance 550 1200 Ω VPG = 0.1V 5
Sync Low Input Voltage (LT8609/LT8609A) 0.4 0.9 V full temp range (l) 5
Sync High Input Voltage (LT8609/LT8609A) 2.7 3.2 V INTVCC = 3.5V, full temp range (l) 5
TR/SS Source Current 1 2 3 µA full temp range (l) 5
TR/SS Pull-Down Resistance 300 900 Ω Fault Condition, TR/SS = 0.1V 5
Spread Spectrum Modulation Frequency (LT8609/LT8609A) 1 3 6 kHz VSYNC = 3.3V 5
FB, TR/SS pin voltage (absolute maximum) 4 V FB, TR/SS 2
SYNC, VOUT pin voltage (absolute maximum) 6 V SYNC, VOUT 2
Operating Junction Temperature Range (LT8609I) -40 125 °C LT8609I/LT8609AI/LT8609BI 2
Storage Temperature Range -65 150 °C 2
Thermal Resistance, Junction-to-Ambient (MSE package) θJA 40 °C/W 10-Lead Plastic MSOP (MSE package) 2

CAD (KiCad official)

  • Symbol: LT8609IMSE#PBF
  • Footprint: Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm
  • 3D model: MSOP-10-EP (KiCad packages3D, STEP)
  • 3D model files: lt8609imse-pbf-etched.step / lt8609imse-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8609imse-pbf.step / lt8609imse-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (30 pp, sha256 bb514bf594e97238, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF