main
Ray Publish 0.1.0 e81aec2

LT8609AIMSE#TRPBF

Analog Devices · DC-DC Converters · MSOP-10-EP

LT8609AIMSE#TRPBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BST power_out Provides a drive voltage higher than the input voltage to the topside power switch, so a 0.1µF boost capacitor must be placed as close as possible to the IC with no series resistor.
2 SW output Output of the internal power switches that connects to the inductor and boost capacitor, and this node should be kept small on the PCB for good performance.
3 INTVCC power_out Internal 3.5V regulator bypass pin with a maximum output current of 20mA that varies between 2.8V and 3.5V, requiring decoupling with at least a 1µF low ESR ceramic capacitor and no external loading.
4 RT passive A resistor tied between RT and ground sets the switching frequency.
5 SYNC input External clock synchronization input that is grounded for low-ripple Burst Mode operation at low loads, driven by a clock to synchronize, left floating for pulse-skipping mode, or tied to INTVCC or 3.2V to 5.0V for pulse-skipping with spread spectrum modulation.
6 FB input Feedback pin that the adjustable-output parts regulate to 0.782V, connected to the feedback resistor divider tap.
7 TR/SS passive Output tracking and soft-start pin where a voltage below 0.782V forces FB to follow it, and an internal 2µA pull-up from INTVCC lets a capacitor program the output voltage ramp rate.
8 PG output Open-drain power good output that remains low until FB is within ±8.5% of the final regulation voltage with no fault conditions, and is valid when VIN is above 3.2V.
9 VIN power_in Supplies current to the internal circuitry and the internal topside power switch, and must be locally bypassed with the input capacitor placed as close as possible to the VIN and GND pins.
10 EN/UV input Shuts the part down when low and enables it when high, with a hysteretic threshold of 1.05V going up and 1.00V going down, and it must be tied to VIN if the shutdown feature is not used.
11 GND power_in Exposed pad that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower the thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-10-EP
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Input Voltage 2.7 3 3.2 V 4
VIN Quiescent Current (LT8609/LT8609A) shutdown 1 4 µA VEN/UV = 0V, VSYNC = 0V 4
VIN Quiescent Current (LT8609/LT8609A) not switching 1.7 12 µA VEN/UV = 2V, Not Switching, VSYNC = 0V 4
VIN Current in Regulation 46 90 µA VIN = 6V, VOUT = 2.7V, Output Load = 100μA 4
VIN Current in Regulation 480 700 µA VIN = 6V, VOUT = 2.7V, Output Load = 1mA 4
Feedback Reference Voltage (E-, I-, H-Grade) 25°C 0.778 0.782 0.786 V E-, I-, H-Grade, VIN = 6V, ILOAD = 100mA 4
Feedback Reference Voltage (E-, I-, H-Grade) full operating temperature range 0.77 0.782 0.794 V E-, I-, H-Grade, VIN = 6V, ILOAD = 100mA (l: full operating temperature range) 4
Feedback Voltage Line Regulation 0.004 0.02 %/V VIN = 4.0V to 40V 4
Feedback Pin Input Current -20 20 nA VFB = 1.0V 4
Minimum On-Time 45 75 ns ILOAD = 1.5A, SYNC = 0V 4
Minimum On-Time 45 60 ns ILOAD = 1.5A, SYNC = 1.9V 4
Minimum Off Time 90 130 ns 4
Oscillator Frequency (LT8609/LT8609A) 155 200 245 kHz RT = 221k, ILOAD = 0.5A 5
Oscillator Frequency (LT8609/LT8609A) 640 700 760 kHz RT = 60.4k, ILOAD = 0.5A 5
Oscillator Frequency (LT8609/LT8609A) 1.925 2 2.075 MHz RT = 18.2k, ILOAD = 0.5A 5
Top Power NMOS Current Limit 3.4 4.5 5.7 A 5
SW Leakage Current 15 µA VIN = 42V, VSW = 40V 5
EN/UV Pin Threshold 0.99 1.05 1.11 V EN/UV Rising 5
EN/UV Pin Current (LT8609/LT8609A) -20 20 nA VEN/UV = 2V 5
PG Upper Threshold Offset from VFB (LT8609/LT8609A) 5 8.5 13 % VFB Rising 5
PG Lower Threshold Offset from VFB (LT8609/LT8609A) 5 8.5 13 % VFB Falling 5
PG Leakage -200 200 nA VPG = 42V 5
PG Pull-Down Resistance 550 1200 Ω VPG = 0.1V 5
Sync Low Input Voltage (LT8609/LT8609A) 0.4 0.9 V 5
Sync High Input Voltage (LT8609/LT8609A) 2.7 3.2 V INTVCC = 3.5V 5
TR/SS Source Current 1 2 3 µA 5
TR/SS Pull-Down Resistance 300 900 Ω Fault Condition, TR/SS = 0.1V 5
Spread Spectrum Modulation Frequency (LT8609/LT8609A) 1 3 6 kHz VSYNC = 3.3V 5
Absolute Maximum Rating: FB, TR/SS 4 V 2
Absolute Maximum Rating: SYNC 6 V 2
Operating Junction Temperature Range -40 125 °C LT8609I/LT8609AI/LT8609BI 2
Storage Temperature Range -65 150 °C 2
Thermal Resistance Junction-to-Ambient (MSE package) θJA 40 °C/W 10-Lead Plastic MSOP (MSE package) 2

CAD (KiCad official)

  • Symbol: LT8609AIMSE#TRPBF
  • Footprint: Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm
  • 3D model: MSOP-10-EP (KiCad packages3D, STEP)
  • 3D model files: lt8609aimse-trpbf-etched.step / lt8609aimse-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8609aimse-trpbf.step / lt8609aimse-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (30 pp, sha256 bb514bf594e97238, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF