main
Ray
Publish 0.1.0
abeae4f
LT8609AHMSE16#PBF
Analog Devices · DC-DC Converters · MSOP-16-EP
LT8609AHMSE16#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | power_out | Provides a drive voltage higher than VIN to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC and do not put a resistor in series with this pin. |
| 2 | NC | unconnected | No connect pin in the 16-lead MSOP pin configuration; the datasheet gives no function for it. |
| 3 | SW | power_out | Output of the internal power switches; connect to the inductor and boost capacitor and keep this node small on the PCB for good performance. |
| 4 | NC | unconnected | No connect pin in the 16-lead MSOP pin configuration; the datasheet gives no function for it. |
| 5 | INTVCC | power_out | Internal 3.5V regulator bypass pin that varies between 2.8V and 3.5V, supplies at most 20mA, must be decoupled to power ground with at least 1µF low-ESR ceramic, and must not be loaded with external circuitry. |
| 6 | RT | passive | A resistor tied between RT and ground sets the switching frequency. |
| 7 | SYNC | input | External clock synchronization input: ground for low-ripple Burst Mode operation, tie to a clock for synchronization, float for pulse-skipping mode without spread spectrum, or tie to INTVCC or 3.2V to 5.0V for pulse-skipping with spread spectrum. |
| 8 | GND | power_in | Ground pin as read from the 16-lead pin layout; the datasheet states GND as the exposed pad (pin 17), so this assignment needs confirmation against the package drawing. |
| 9 | FB | input | Feedback pin that the adjustable-output parts regulate to 0.782V; connect the feedback resistor divider tap to this pin. |
| 10 | FB | input | The layout lists FB twice on the right-hand side of the 16-lead pin configuration; this pin is taken as the feedback pin (0.782V regulation) but its assignment needs confirmation. |
| 11 | TR/SS | input | Output tracking and soft-start pin: a voltage below 0.782V forces FB to follow it, and a capacitor sets the start-up ramp via an internal 2µA pull-up from INTVCC; the pin is pulled to ground through 300Ω during shutdown and fault conditions. |
| 12 | PG | output | Open-drain power-good output that stays low until FB is within ±8.5% of the regulation voltage (±7.5% for fixed-output parts) with no faults, and is valid when VIN is above 3.2V. |
| 13 | NC | unconnected | No connect pin in the 16-lead MSOP pin configuration; the datasheet gives no function for it. |
| 14 | VIN | power_in | Supplies the internal circuitry and the internal topside power switch; it must be locally bypassed with the input capacitor placed as close as possible to the VIN and GND pins. |
| 15 | NC | unconnected | No connect pin in the 16-lead MSOP pin configuration; the datasheet gives no function for it. |
| 16 | EN/UV | input | Enable and undervoltage input: the part shuts down when low and is active when high, with a hysteretic threshold of 1.05V rising and 1.00V falling; tie to VIN if unused. |
| 17 | GND | power_in | Exposed pad is GND and must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | VIN(MIN) | 2.7 | 3 | 3.2 | V | 4 | |
| VIN Quiescent Current (shutdown) | IQ | 1 | 4 | µA | VEN/UV = 0V, VSYNC = 0V | 4 | |
| VIN Quiescent Current (not switching) | IQ | 1.7 | 12 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V; full temperature range | 4 | |
| VIN Current in Regulation | IIN | 46 | 90 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 100µA | 4 | |
| VIN Current in Regulation | IIN | 480 | 700 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 1mA; full temperature range | 4 | |
| Feedback Reference Voltage (E/I/H grade) | VFB | 0.778 | 0.782 | 0.786 | V | VIN = 6V, ILOAD = 100mA | 4 |
| Feedback Reference Voltage (E/I/H grade) | VFB | 0.77 | 0.782 | 0.794 | V | VIN = 6V, ILOAD = 100mA; full temperature range | 4 |
| Feedback Pin Input Current | IFB | -20 | 20 | nA | VFB = 1.0V; full temperature range | 4 | |
| Feedback Voltage Line Regulation | 0.004 | 0.02 | %/V | VIN = 4.0V to 40V; full temperature range | 4 | ||
| Minimum On-Time | tON(MIN) | 45 | 75 | ns | ILOAD = 1.5A, SYNC = 0V; full temperature range | 4 | |
| Minimum On-Time | tON(MIN) | 45 | 60 | ns | ILOAD = 1.5A, SYNC = 1.9V; full temperature range | 4 | |
| Minimum Off Time | tOFF(MIN) | 90 | 130 | ns | 4 | ||
| Oscillator Frequency | fSW | 155 | 200 | 245 | kHz | RT = 221k, ILOAD = 0.5A; full temperature range | 5 |
| Oscillator Frequency | fSW | 640 | 700 | 760 | kHz | RT = 60.4k, ILOAD = 0.5A; full temperature range | 5 |
| Oscillator Frequency | fSW | 1.925 | 2 | 2.075 | MHz | RT = 18.2k, ILOAD = 0.5A; full temperature range | 5 |
| Top Power NMOS Current Limit | ILIM | 3.4 | 4.5 | 5.7 | A | full temperature range | 5 |
| SW Leakage Current | ISW | 15 | µA | VIN = 42V, VSW = 40V; full temperature range | 5 | ||
| EN/UV Pin Threshold | VEN/UV | 0.99 | 1.05 | 1.11 | V | EN/UV Rising; full temperature range | 5 |
| EN/UV Pin Current | IEN/UV | -20 | 20 | nA | VEN/UV = 2V; full temperature range | 5 | |
| PG Upper Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Rising; full temperature range | 5 | |
| PG Lower Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Falling; full temperature range | 5 | |
| PG Leakage | IPG | -200 | 200 | nA | VPG = 42V; full temperature range | 5 | |
| PG Pull-Down Resistance | RPG | 550 | 1200 | Ω | VPG = 0.1V | 5 | |
| Sync Low Input Voltage | VSYNC(LOW) | 0.4 | 0.9 | V | full temperature range | 5 | |
| Sync High Input Voltage | VSYNC(HIGH) | 2.7 | 3.2 | V | INTVCC = 3.5V; full temperature range | 5 | |
| TR/SS Source Current | ITR/SS | 1 | 2 | 3 | µA | full temperature range | 5 |
| TR/SS Pull-Down Resistance | RTR/SS | 300 | 900 | Ω | Fault Condition, TR/SS = 0.1V | 5 | |
| Spread Spectrum Modulation Frequency | fSS | 1 | 3 | 6 | kHz | VSYNC = 3.3V | 5 |
| Top Power NMOS On-Resistance | RDS(ON) | 185 | mΩ | ILOAD = 1A | 5 | ||
| Bottom Power NMOS On-Resistance | RDS(ON) | 115 | mΩ | 5 | |||
| EN/UV Pin Hysteresis | 50 | mV | 5 | ||||
| PG Hysteresis | 0.5 | % | 5 | ||||
| FB, TR/SS pin voltage | VFB, VTR/SS | 4 | V | Absolute maximum rating (Note 1) | 2 | ||
| SYNC, VOUT pin voltage | VSYNC, VOUT | 6 | V | Absolute maximum rating (Note 1) | 2 | ||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Operating Junction Temperature Range (LT8609AH) | TJ | -40 | 150 | °C | LT8609AH ordering grade | 2 | |
| Thermal Resistance Junction-to-Ambient | θJA | 40 | °C/W | 16-Lead MSOP (MS package) | 2 | ||
| Thermal Resistance Junction-to-Case (Pad) | θJC(PAD) | 10 | °C/W | 16-Lead MSOP (MS package) | 2 |
CAD (KiCad official)
- Symbol:
LT8609AHMSE16#PBF - Footprint:
Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm - 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lt8609ahmse16-pbf-etched.step/lt8609ahmse16-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8609ahmse16-pbf.step/lt8609ahmse16-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (30 pp, sha256
bb514bf594e97238, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT8609AHMSE16#PBF
**Analog Devices** · DC-DC Converters · MSOP-16-EP
LT8609AHMSE16#PBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | power_out | Provides a drive voltage higher than VIN to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC and do not put a resistor in series with this pin. |
| 2 | NC | unconnected | No connect pin in the 16-lead MSOP pin configuration; the datasheet gives no function for it. |
| 3 | SW | power_out | Output of the internal power switches; connect to the inductor and boost capacitor and keep this node small on the PCB for good performance. |
| 4 | NC | unconnected | No connect pin in the 16-lead MSOP pin configuration; the datasheet gives no function for it. |
| 5 | INTVCC | power_out | Internal 3.5V regulator bypass pin that varies between 2.8V and 3.5V, supplies at most 20mA, must be decoupled to power ground with at least 1µF low-ESR ceramic, and must not be loaded with external circuitry. |
| 6 | RT | passive | A resistor tied between RT and ground sets the switching frequency. |
| 7 | SYNC | input | External clock synchronization input: ground for low-ripple Burst Mode operation, tie to a clock for synchronization, float for pulse-skipping mode without spread spectrum, or tie to INTVCC or 3.2V to 5.0V for pulse-skipping with spread spectrum. |
| 8 | GND | power_in | Ground pin as read from the 16-lead pin layout; the datasheet states GND as the exposed pad (pin 17), so this assignment needs confirmation against the package drawing. |
| 9 | FB | input | Feedback pin that the adjustable-output parts regulate to 0.782V; connect the feedback resistor divider tap to this pin. |
| 10 | FB | input | The layout lists FB twice on the right-hand side of the 16-lead pin configuration; this pin is taken as the feedback pin (0.782V regulation) but its assignment needs confirmation. |
| 11 | TR/SS | input | Output tracking and soft-start pin: a voltage below 0.782V forces FB to follow it, and a capacitor sets the start-up ramp via an internal 2µA pull-up from INTVCC; the pin is pulled to ground through 300Ω during shutdown and fault conditions. |
| 12 | PG | output | Open-drain power-good output that stays low until FB is within ±8.5% of the regulation voltage (±7.5% for fixed-output parts) with no faults, and is valid when VIN is above 3.2V. |
| 13 | NC | unconnected | No connect pin in the 16-lead MSOP pin configuration; the datasheet gives no function for it. |
| 14 | VIN | power_in | Supplies the internal circuitry and the internal topside power switch; it must be locally bypassed with the input capacitor placed as close as possible to the VIN and GND pins. |
| 15 | NC | unconnected | No connect pin in the 16-lead MSOP pin configuration; the datasheet gives no function for it. |
| 16 | EN/UV | input | Enable and undervoltage input: the part shuts down when low and is active when high, with a hysteretic threshold of 1.05V rising and 1.00V falling; tie to VIN if unused. |
| 17 | GND | power_in | Exposed pad is GND and must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Power Supply Chip |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | VIN(MIN) | 2.7 | 3 | 3.2 | V | | 4 |
| VIN Quiescent Current (shutdown) | IQ | | 1 | 4 | µA | VEN/UV = 0V, VSYNC = 0V | 4 |
| VIN Quiescent Current (not switching) | IQ | | 1.7 | 12 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V; full temperature range | 4 |
| VIN Current in Regulation | IIN | | 46 | 90 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 100µA | 4 |
| VIN Current in Regulation | IIN | | 480 | 700 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 1mA; full temperature range | 4 |
| Feedback Reference Voltage (E/I/H grade) | VFB | 0.778 | 0.782 | 0.786 | V | VIN = 6V, ILOAD = 100mA | 4 |
| Feedback Reference Voltage (E/I/H grade) | VFB | 0.77 | 0.782 | 0.794 | V | VIN = 6V, ILOAD = 100mA; full temperature range | 4 |
| Feedback Pin Input Current | IFB | -20 | | 20 | nA | VFB = 1.0V; full temperature range | 4 |
| Feedback Voltage Line Regulation | | | 0.004 | 0.02 | %/V | VIN = 4.0V to 40V; full temperature range | 4 |
| Minimum On-Time | tON(MIN) | | 45 | 75 | ns | ILOAD = 1.5A, SYNC = 0V; full temperature range | 4 |
| Minimum On-Time | tON(MIN) | | 45 | 60 | ns | ILOAD = 1.5A, SYNC = 1.9V; full temperature range | 4 |
| Minimum Off Time | tOFF(MIN) | | 90 | 130 | ns | | 4 |
| Oscillator Frequency | fSW | 155 | 200 | 245 | kHz | RT = 221k, ILOAD = 0.5A; full temperature range | 5 |
| Oscillator Frequency | fSW | 640 | 700 | 760 | kHz | RT = 60.4k, ILOAD = 0.5A; full temperature range | 5 |
| Oscillator Frequency | fSW | 1.925 | 2 | 2.075 | MHz | RT = 18.2k, ILOAD = 0.5A; full temperature range | 5 |
| Top Power NMOS Current Limit | ILIM | 3.4 | 4.5 | 5.7 | A | full temperature range | 5 |
| SW Leakage Current | ISW | | | 15 | µA | VIN = 42V, VSW = 40V; full temperature range | 5 |
| EN/UV Pin Threshold | VEN/UV | 0.99 | 1.05 | 1.11 | V | EN/UV Rising; full temperature range | 5 |
| EN/UV Pin Current | IEN/UV | -20 | | 20 | nA | VEN/UV = 2V; full temperature range | 5 |
| PG Upper Threshold Offset from VFB | | 5 | 8.5 | 13 | % | VFB Rising; full temperature range | 5 |
| PG Lower Threshold Offset from VFB | | 5 | 8.5 | 13 | % | VFB Falling; full temperature range | 5 |
| PG Leakage | IPG | -200 | | 200 | nA | VPG = 42V; full temperature range | 5 |
| PG Pull-Down Resistance | RPG | | 550 | 1200 | Ω | VPG = 0.1V | 5 |
| Sync Low Input Voltage | VSYNC(LOW) | 0.4 | | 0.9 | V | full temperature range | 5 |
| Sync High Input Voltage | VSYNC(HIGH) | 2.7 | | 3.2 | V | INTVCC = 3.5V; full temperature range | 5 |
| TR/SS Source Current | ITR/SS | 1 | 2 | 3 | µA | full temperature range | 5 |
| TR/SS Pull-Down Resistance | RTR/SS | | 300 | 900 | Ω | Fault Condition, TR/SS = 0.1V | 5 |
| Spread Spectrum Modulation Frequency | fSS | 1 | 3 | 6 | kHz | VSYNC = 3.3V | 5 |
| Top Power NMOS On-Resistance | RDS(ON) | | 185 | | mΩ | ILOAD = 1A | 5 |
| Bottom Power NMOS On-Resistance | RDS(ON) | | 115 | | mΩ | | 5 |
| EN/UV Pin Hysteresis | | | 50 | | mV | | 5 |
| PG Hysteresis | | | 0.5 | | % | | 5 |
| FB, TR/SS pin voltage | VFB, VTR/SS | | | 4 | V | Absolute maximum rating (Note 1) | 2 |
| SYNC, VOUT pin voltage | VSYNC, VOUT | | | 6 | V | Absolute maximum rating (Note 1) | 2 |
| Storage Temperature Range | TSTG | -65 | | 150 | °C | | 2 |
| Operating Junction Temperature Range (LT8609AH) | TJ | -40 | | 150 | °C | LT8609AH ordering grade | 2 |
| Thermal Resistance Junction-to-Ambient | θJA | | 40 | | °C/W | 16-Lead MSOP (MS package) | 2 |
| Thermal Resistance Junction-to-Case (Pad) | θJC(PAD) | | 10 | | °C/W | 16-Lead MSOP (MS package) | 2 |
## CAD (KiCad official)
- Symbol: `LT8609AHMSE16#PBF`
- Footprint: `Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm`
- 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files: `lt8609ahmse16-pbf-etched.step` / `lt8609ahmse16-pbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt8609ahmse16-pbf.step` / `lt8609ahmse16-pbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/LT8609-8609A-8609B.pdf) (30 pp, sha256 `bb514bf594e97238`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt8609ahmse16-pbf-datasheet.pdf)