main
Ray Publish 0.1.0 c897d0e

LT8609AEDDM#PBF

Analog Devices · DC-DC Converters · DFN-10-EP(3x3)

LT8609AEDDM#PBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BST power_out Provides a drive voltage higher than VIN to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC and do not place a resistor in series with this pin.
2 SW output Output of the internal power switches; connect to the inductor and boost capacitor and keep this node small on the PCB for good performance.
3 INTVCC power_out Internal 3.5V regulator bypass pin that powers the internal drivers and control circuits; maximum output current is 20mA, voltage varies between 2.8V and 3.5V, decouple with at least 1µF low-ESR ceramic, and do not load with external circuitry.
4 RT passive A resistor tied between RT and ground sets the switching frequency (200kHz to 2.2MHz operating range).
5 SYNC input External clock synchronization input: ground for low-ripple Burst Mode operation at low loads, tie to a clock to synchronize, leave floating for pulse-skipping mode, or tie to INTVCC or 3.2V to 5.0V for pulse-skipping with spread spectrum modulation.
6 FB input Feedback pin for the adjustable output part, regulated to 0.782V; connect the feedback resistor divider tap to this pin.
7 TR/SS passive Output tracking and soft-start pin; a voltage below 0.782V forces FB to follow it, an internal 2µA pull-up from INTVCC sets the output slew rate via a capacitor, and it is pulled to ground through 300Ω during shutdown and fault conditions.
8 PG output Open-drain power-good output that stays low until FB is within ±8.5% of the regulation voltage with no fault conditions, and is valid when VIN is above 3.2V.
9 VIN power_in Supplies current to the internal circuitry and the internal topside power switch from a 3.0V to 42V input and must be locally bypassed with the input capacitor placed close to the VIN and GND pins.
10 EN/UV input Enable and undervoltage input: the part is shut down when low and active when high, with a hysteretic threshold of 1.05V rising and 1.00V falling; tie to VIN if shutdown is not used.
11 GND power_in Exposed pad that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance (θJA = 45°C/W, θJC = 10°C/W).

Key specifications

Parameter Value
Manufacturer Analog Devices
Package DFN-10-EP(3x3)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Input Voltage 2.7 3 3.2 V 4
VIN Quiescent Current 1 4 µA VEN/UV = 0V, VSYNC = 0V 4
VIN Quiescent Current 1.7 12 µA VEN/UV = 2V, Not Switching, VSYNC = 0V 4
VIN Current in Regulation 46 90 µA VIN = 6V, VOUT = 2.7V, Output Load = 100μA 4
VIN Current in Regulation 480 700 µA VIN = 6V, VOUT = 2.7V, Output Load = 1mA 4
Feedback Reference Voltage 0.778 0.782 0.786 V VIN = 6V, ILOAD = 100mA 4
Feedback Reference Voltage (over temperature, l) 0.77 0.782 0.794 V VIN = 6V, ILOAD = 100mA 4
Feedback Voltage Line Regulation 0.004 0.02 %/V VIN = 4.0V to 40V 4
Feedback Pin Input Current -20 20 nA VFB = 1.0V 4
Minimum On-Time 45 75 ns ILOAD = 1.5A, SYNC = 0V 4
Minimum On-Time 45 60 ns ILOAD = 1.5A, SYNC = 1.9V 4
Minimum Off Time 90 130 ns 4
Oscillator Frequency 155 200 245 kHz RT = 221k, ILOAD = 0.5A 5
Oscillator Frequency 640 700 760 kHz RT = 60.4k, ILOAD = 0.5A 5
Oscillator Frequency 1.925 2 2.075 MHz RT = 18.2k, ILOAD = 0.5A 5
Top Power NMOS Current Limit 3.4 4.5 5.7 A 5
SW Leakage Current 15 µA VIN = 42V, VSW = 40V 5
EN/UV Pin Threshold 0.99 1.05 1.11 V EN/UV Rising 5
EN/UV Pin Current -20 20 nA VEN/UV = 2V 5
PG Upper Threshold Offset from VFB 5 8.5 13 % VFB Rising 5
PG Lower Threshold Offset from VFB 5 8.5 13 % VFB Falling 5
PG Leakage -200 200 nA VPG = 42V 5
PG Pull-Down Resistance 550 1200 Ω VPG = 0.1V 5
Sync Low Input Voltage 0.4 0.9 V 5
Sync High Input Voltage 2.7 3.2 V INTVCC = 3.5V 5
TR/SS Source Current 1 2 3 µA 5
TR/SS Pull-Down Resistance 300 900 Ω Fault Condition, TR/SS = 0.1V 5
Spread Spectrum Modulation Frequency 1 3 6 kHz VSYNC = 3.3V 5
FB, TR/SS pin voltage 4 V 2
SYNC pin voltage 6 V 2
Operating Junction Temperature Range -40 125 °C LT8609AE grade 2
Storage Temperature Range -65 150 °C 2
Thermal Resistance Junction-to-Ambient (DDM package) θJA 45 °C/W DDM package 2
Thermal Resistance Junction-to-Case (DDM package) θJC 10 °C/W DDM package 2

CAD (KiCad official)

  • Symbol: LT8609AEDDM#PBF
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: lt8609aeddm-pbf-etched.step / lt8609aeddm-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8609aeddm-pbf.step / lt8609aeddm-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (30 pp, sha256 bb514bf594e97238, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF