3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT8609AEDDM-5#PBF
Analog Devices · DC-DC Converters · DFN-10-EP(3x3)
LT8609AEDDM-5#PBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | power_out | Provides a drive voltage higher than VIN to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC and do not place a resistor in series with this pin. |
| 2 | SW | output | Output of the internal power switches that connects to the inductor and boost capacitor, and this node should be kept small on the PCB for good performance. |
| 3 | INTVCC | power_out | Internal 3.5V regulator bypass pin with a maximum output current of 20mA, varying between 2.8V and 3.5V, to be decoupled to power ground with at least 1µF low ESR ceramic and not loaded with external circuitry. |
| 4 | RT | passive | A resistor is tied between RT and ground to set the switching frequency (200kHz to 2.2MHz adjustable range per the features list). |
| 5 | SYNC | input | External clock synchronization input: ground for low-ripple Burst Mode operation, tie to a clock to synchronize, float for pulse-skipping mode without spread spectrum, or tie to INTVCC or 3.2V to 5.0V for pulse-skipping with spread spectrum. |
| 6 | VOUT | input | On the LT8609A-5 fixed output part this pin connects an 8.95MΩ internal feedback divider that programs the regulated 5V output. |
| 7 | TR/SS | bidirectional | Output tracking and soft-start pin where a voltage below 0.782V regulates the output to track it (6.39× on the 5V option) and a 2µA internal pull-up from INTVCC programs the output ramp rate, with a 300Ω pull-down during shutdown and faults so a series resistor is needed when driven from a low-impedance source. |
| 8 | PG | output | Open-drain power-good output that stays low until VOUT is within ±7.5% of the final regulation voltage with no fault conditions, and is valid when VIN is above 3.2V regardless of EN/UV state. |
| 9 | VIN | power_in | Supplies current to the internal circuitry and topside power switch over the 3.0V to 42V input range, and must be locally bypassed with the input capacitor positive terminal placed as close as possible to this pin. |
| 10 | EN/UV | input | Shuts the part down when low and enables it when high, with a hysteretic threshold of 1.05V rising and 1.00V falling that can be used to program a VIN undervoltage lockout; tie to VIN if the shutdown feature is not used. |
| 11 | GND | power_in | Exposed pad that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 2.7 | 3 | 3.2 | V | 4 | ||
| VIN Quiescent Current (shutdown) | 1 | 4 | µA | VEN/UV = 0V, VSYNC = 0V | 4 | ||
| VIN Quiescent Current (not switching) | 1.7 | 12 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V (l) | 4 | ||
| VIN Current in Regulation (100µA load) | 46 | 90 | µA | VIN = 12V, VOUT = 5V, ILOAD = 100µA (l) | 4 | ||
| VIN Current in Regulation (1mA load) | 480 | 700 | µA | VIN = 12V, VOUT = 5V, ILOAD = 1mA (l) | 4 | ||
| Output Reference Voltage LT8609A-5 | 4.97 | 5 | 5.03 | V | VIN = 12V, ILOAD = 100mA (25°C) | 4 | |
| Output Reference Voltage LT8609A-5 (full temperature range) | 4.89 | 5 | 5.11 | V | VIN = 12V, ILOAD = 100mA (l, full operating temperature range) | 4 | |
| Output Voltage Line Regulation LT8609A-5 | 0.004 | 0.02 | %/V | VIN = 6.0V to 40V (l) | 4 | ||
| Feedback Pin Input Current | -20 | 20 | nA | VFB = 1.0V (l) | 4 | ||
| Minimum On-Time | 45 | 75 | ns | ILOAD = 1.5A, SYNC = 0V | 4 | ||
| Minimum On-Time (SYNC high) | 45 | 60 | ns | ILOAD = 1.5A, SYNC = 1.9V (l) | 4 | ||
| Minimum Off Time | 90 | 130 | ns | 4 | |||
| Oscillator Frequency (RT = 221k) | 155 | 200 | 245 | kHz | RT = 221k, ILOAD = 0.5A (l) | 5 | |
| Oscillator Frequency (RT = 60.4k) | 640 | 700 | 760 | kHz | RT = 60.4k, ILOAD = 0.5A (l) | 5 | |
| Oscillator Frequency (RT = 18.2k) | 1.925 | 2 | 2.075 | MHz | RT = 18.2k, ILOAD = 0.5A (l) | 5 | |
| Top Power NMOS Current Limit | 3.4 | 4.5 | 5.7 | A | (l) | 5 | |
| EN/UV Pin Threshold (rising) | 0.99 | 1.05 | 1.11 | V | EN/UV Rising (l) | 5 | |
| EN/UV Pin Current | -20 | 20 | nA | VEN/UV = 2V (l) | 5 | ||
| PG Upper Threshold Offset from VOUT | 5 | 7.5 | 11 | % | VOUT Rising (l) | 5 | |
| PG Lower Threshold Offset from VOUT | 5 | 7.5 | 11 | % | VOUT Falling (l) | 5 | |
| PG Leakage | -200 | 200 | nA | VPG = 42V (l) | 5 | ||
| PG Pull-Down Resistance | 550 | 1200 | Ω | VPG = 0.1V | 5 | ||
| Sync Low Input Voltage | 0.4 | 0.9 | V | LT8609/LT8609A (l) | 5 | ||
| Sync High Input Voltage | 2.7 | 3.2 | V | LT8609/LT8609A, INTVCC = 3.5V (l) | 5 | ||
| TR/SS Source Current | 1 | 2 | 3 | µA | (l) | 5 | |
| TR/SS Pull-Down Resistance | 300 | 900 | Ω | Fault Condition, TR/SS = 0.1V | 5 | ||
| Spread Spectrum Modulation Frequency | 1 | 3 | 6 | kHz | VSYNC = 3.3V | 5 | |
| FB, TR/SS voltage (absolute maximum) | 4 | V | 2 | ||||
| SYNC, VOUT voltage (absolute maximum) | 6 | V | 2 | ||||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | LT8609AE (E grade) | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Thermal Resistance Junction-to-Ambient (DDM package) | θJA | 45 | °C/W | DDM 10-lead 3mm × 3mm DFN | 2 | ||
| Thermal Resistance Junction-to-Case (DDM package) | θJC | 10 | °C/W | DDM 10-lead 3mm × 3mm DFN | 2 |
CAD (KiCad official)
- Symbol:
LT8609AEDDM-5#PBF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lt8609aeddm-5-pbf-etched.step/lt8609aeddm-5-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8609aeddm-5-pbf.step/lt8609aeddm-5-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (30 pp, sha256
bb514bf594e97238, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).