main
Ray
Publish 0.1.0
f0cf7e7
LT8608IDC#TRMPBF
Analog Devices · DC-DC Converters · DFN-8-EP(2x2)
LT8608IDC#TRMPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | passive | Provides a drive voltage higher than VIN to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC and do not place a resistor in series with this pin. |
| 2 | SW | output | Output of the internal power switches that connects to the inductor and boost capacitor; this node should be kept small on the PCB for good performance. |
| 3 | INTVCC | power_out | Internal 3.5V regulator bypass pin that varies between 2.8V and 3.5V with 20mA maximum output current; decouple with at least 1µF low ESR ceramic and do not load it with external circuitry. |
| 4 | RT | passive | A resistor from RT to ground sets the switching frequency, which must be equal to or below the lowest synchronization input when synchronizing. |
| 5 | FB | input | Regulates to 0.778V; the feedback resistor divider tap connects to this pin. |
| 6 | PG | output | Open-drain power-good output that remains low until FB is within ±8.5% of the final regulation voltage with no fault conditions, and is valid when VIN is above 3.2V. |
| 7 | VIN | power_in | Supplies the internal circuitry and topside power switch and must be locally bypassed, with an absolute maximum rating of 42V. |
| 8 | EN/UV | input | Shuts the LT8608 down when low and enables it when high, with a hysteretic threshold of 1.05V rising and 1.00V falling; tie to VIN if the shutdown feature is not used. |
| 9 | GND | power_in | Exposed pad that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-8-EP(2x2) |
| Category | Power Supply Chip |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 2.5 | 3 | 3.2 | V | 2 | ||
| VIN Quiescent Current (EN/UV = 0V, SYNC = 0V) | IQ | 1 | 4 | µA | VEN/UV = 0V, VSYNC = 0V | 2 | |
| VIN Quiescent Current (not switching) | IQ | 1.7 | 12 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V or LT8608 DFN, VIN ≤ 36V, full operating temperature range | 2 | |
| VIN Current in Regulation (100µA load) | 56 | 90 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 100µA | 2 | ||
| VIN Current in Regulation (1mA load) | 500 | 700 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 1mA, full operating temperature range | 2 | ||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | LT8608I | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| VIN, EN/UV, PG Absolute Maximum Voltage | VIN | 42 | V | 2 | |||
| FB Absolute Maximum Voltage | FB | 4 | V | 2 | |||
| Wide Input Voltage Range | VIN | 3 | 42 | V | Features section | 1 | |
| Feedback Reference Voltage (DFN, 25°C) | VFB | 0.773 | 0.778 | 0.783 | V | VIN = 6V, ILOAD = 100mA | 3 |
| Feedback Reference Voltage (DFN, full temperature range) | VFB | 0.753 | 0.778 | 0.803 | V | VIN = 6V, ILOAD = 100mA, full operating temperature range | 3 |
| Feedback Voltage Line Regulation | -0.06 | 0.02 | 0.06 | %/V | VIN = 4.0V to 40V, full operating temperature range | 3 | |
| Feedback Pin Input Current | IFB | -20 | 20 | nA | VFB = 1V, full operating temperature range | 3 | |
| Minimum On-Time | tON(MIN) | 35 | 65 | ns | ILOAD = 1A, SYNC = 0V or LT8608 DFN, full operating temperature range | 3 | |
| Minimum Off Time | tOFF(MIN) | 93 | 130 | ns | 3 | ||
| Oscillator Frequency (DFN, RT = 221k) | fSW | 130 | 200 | 270 | kHz | RT = 221k, ILOAD = 500mA, full operating temperature range | 3 |
| Oscillator Frequency (DFN, RT = 60.4k) | fSW | 610 | 700 | 790 | kHz | RT = 60.4k, ILOAD = 500mA, full operating temperature range | 3 |
| Oscillator Frequency (DFN, RT = 18.2k) | fSW | 1.85 | 2 | 2.15 | MHz | RT = 18.2k, ILOAD = 200mA, full operating temperature range | 3 |
| Top Power NMOS On-Resistance | RDS(ON) | 350 | mΩ | ILOAD = 0.5A | 3 | ||
| Top Power NMOS Current Limit | ILIM | 2.1 | 2.9 | 3.9 | A | full operating temperature range | 3 |
| Bottom Power NMOS On-Resistance | RDS(ON) | 230 | mΩ | 3 | |||
| SW Leakage Current | ISW | 15 | µA | VIN = 36V, full operating temperature range | 3 | ||
| EN/UV Pin Threshold | VEN/UV | 0.99 | 1.05 | 1.11 | V | EN/UV Rising, full operating temperature range | 3 |
| EN/UV Pin Hysteresis | 50 | mV | 3 | ||||
| EN/UV Pin Current | IEN/UV | -20 | 20 | nA | VEN/UV = 2V, full operating temperature range | 3 | |
| PG Upper Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Rising, full operating temperature range | 3 | |
| PG Lower Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Falling, full operating temperature range | 3 | |
| PG Hysteresis | 0.5 | % | 3 | ||||
| PG Leakage | IPG | -200 | 200 | nA | VPG = 42V, full operating temperature range | 3 | |
| PG Pull-Down Resistance | RPG | 550 | 1200 | Ω | VPG = 0.1V | 3 |
CAD (KiCad official)
- Symbol:
LT8608IDC#TRMPBF - Footprint:
Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.5mm_EP0.6x1.2mm - 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files:
lt8608idc-trmpbf-etched.step/lt8608idc-trmpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8608idc-trmpbf.step/lt8608idc-trmpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (24 pp, sha256
ef5ca800fd4c6a67, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT8608IDC#TRMPBF
**Analog Devices** · DC-DC Converters · DFN-8-EP(2x2)
LT8608IDC#TRMPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | passive | Provides a drive voltage higher than VIN to the topside power switch; place a 0.1µF boost capacitor as close as possible to the IC and do not place a resistor in series with this pin. |
| 2 | SW | output | Output of the internal power switches that connects to the inductor and boost capacitor; this node should be kept small on the PCB for good performance. |
| 3 | INTVCC | power_out | Internal 3.5V regulator bypass pin that varies between 2.8V and 3.5V with 20mA maximum output current; decouple with at least 1µF low ESR ceramic and do not load it with external circuitry. |
| 4 | RT | passive | A resistor from RT to ground sets the switching frequency, which must be equal to or below the lowest synchronization input when synchronizing. |
| 5 | FB | input | Regulates to 0.778V; the feedback resistor divider tap connects to this pin. |
| 6 | PG | output | Open-drain power-good output that remains low until FB is within ±8.5% of the final regulation voltage with no fault conditions, and is valid when VIN is above 3.2V. |
| 7 | VIN | power_in | Supplies the internal circuitry and topside power switch and must be locally bypassed, with an absolute maximum rating of 42V. |
| 8 | EN/UV | input | Shuts the LT8608 down when low and enables it when high, with a hysteretic threshold of 1.05V rising and 1.00V falling; tie to VIN if the shutdown feature is not used. |
| 9 | GND | power_in | Exposed pad that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-8-EP(2x2) |
| Category | Power Supply Chip |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | | 2.5 | 3 | 3.2 | V | | 2 |
| VIN Quiescent Current (EN/UV = 0V, SYNC = 0V) | IQ | | 1 | 4 | µA | VEN/UV = 0V, VSYNC = 0V | 2 |
| VIN Quiescent Current (not switching) | IQ | | 1.7 | 12 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V or LT8608 DFN, VIN ≤ 36V, full operating temperature range | 2 |
| VIN Current in Regulation (100µA load) | | | 56 | 90 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 100µA | 2 |
| VIN Current in Regulation (1mA load) | | | 500 | 700 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 1mA, full operating temperature range | 2 |
| Operating Junction Temperature Range | TJ | -40 | | 125 | °C | LT8608I | 2 |
| Storage Temperature Range | TSTG | -65 | | 150 | °C | | 2 |
| VIN, EN/UV, PG Absolute Maximum Voltage | VIN | | | 42 | V | | 2 |
| FB Absolute Maximum Voltage | FB | | | 4 | V | | 2 |
| Wide Input Voltage Range | VIN | 3 | | 42 | V | Features section | 1 |
| Feedback Reference Voltage (DFN, 25°C) | VFB | 0.773 | 0.778 | 0.783 | V | VIN = 6V, ILOAD = 100mA | 3 |
| Feedback Reference Voltage (DFN, full temperature range) | VFB | 0.753 | 0.778 | 0.803 | V | VIN = 6V, ILOAD = 100mA, full operating temperature range | 3 |
| Feedback Voltage Line Regulation | | -0.06 | 0.02 | 0.06 | %/V | VIN = 4.0V to 40V, full operating temperature range | 3 |
| Feedback Pin Input Current | IFB | -20 | | 20 | nA | VFB = 1V, full operating temperature range | 3 |
| Minimum On-Time | tON(MIN) | 35 | | 65 | ns | ILOAD = 1A, SYNC = 0V or LT8608 DFN, full operating temperature range | 3 |
| Minimum Off Time | tOFF(MIN) | | 93 | 130 | ns | | 3 |
| Oscillator Frequency (DFN, RT = 221k) | fSW | 130 | 200 | 270 | kHz | RT = 221k, ILOAD = 500mA, full operating temperature range | 3 |
| Oscillator Frequency (DFN, RT = 60.4k) | fSW | 610 | 700 | 790 | kHz | RT = 60.4k, ILOAD = 500mA, full operating temperature range | 3 |
| Oscillator Frequency (DFN, RT = 18.2k) | fSW | 1.85 | 2 | 2.15 | MHz | RT = 18.2k, ILOAD = 200mA, full operating temperature range | 3 |
| Top Power NMOS On-Resistance | RDS(ON) | | 350 | | mΩ | ILOAD = 0.5A | 3 |
| Top Power NMOS Current Limit | ILIM | 2.1 | 2.9 | 3.9 | A | full operating temperature range | 3 |
| Bottom Power NMOS On-Resistance | RDS(ON) | | 230 | | mΩ | | 3 |
| SW Leakage Current | ISW | | | 15 | µA | VIN = 36V, full operating temperature range | 3 |
| EN/UV Pin Threshold | VEN/UV | 0.99 | 1.05 | 1.11 | V | EN/UV Rising, full operating temperature range | 3 |
| EN/UV Pin Hysteresis | | | 50 | | mV | | 3 |
| EN/UV Pin Current | IEN/UV | -20 | | 20 | nA | VEN/UV = 2V, full operating temperature range | 3 |
| PG Upper Threshold Offset from VFB | | 5 | 8.5 | 13 | % | VFB Rising, full operating temperature range | 3 |
| PG Lower Threshold Offset from VFB | | 5 | 8.5 | 13 | % | VFB Falling, full operating temperature range | 3 |
| PG Hysteresis | | | 0.5 | | % | | 3 |
| PG Leakage | IPG | -200 | | 200 | nA | VPG = 42V, full operating temperature range | 3 |
| PG Pull-Down Resistance | RPG | | 550 | 1200 | Ω | VPG = 0.1V | 3 |
## CAD (KiCad official)
- Symbol: `LT8608IDC#TRMPBF`
- Footprint: `Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.5mm_EP0.6x1.2mm`
- 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files: `lt8608idc-trmpbf-etched.step` / `lt8608idc-trmpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt8608idc-trmpbf.step` / `lt8608idc-trmpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/lt8608.pdf) (24 pp, sha256 `ef5ca800fd4c6a67`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt8608idc-trmpbf-datasheet.pdf)