Generated by kicad-footprint-generator · KiCad file format 20260206
LT8606EMSE#PBF
Analog Devices · DC-DC Converters · MSOP-10-EP
LT8606EMSE#PBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | power_out | Provides a drive voltage higher than VIN to the topside power switch, requiring a 0.1µF boost capacitor placed as close as possible to the IC with no series resistor. |
| 2 | SW | output | Output of the internal power switches that connects to the inductor and boost capacitor, and should be kept small on the PCB for good performance. |
| 3 | INTVCC | power_out | Internal 3.5V regulator bypass pin with a maximum output current of 20mA, varying between 2.8V and 3.5V, that must be decoupled with at least a 1µF low ESR ceramic capacitor and not loaded externally. |
| 4 | RT | passive | A resistor from RT to ground sets the switching frequency, and when synchronizing it must set a frequency equal to or below the lowest sync input. |
| 5 | SYNC | input | External clock synchronization input (MSOP only) that selects Burst Mode operation when grounded, pulse-skipping when floated, and pulse-skipping with spread spectrum when tied to INTVCC or 3.2V to 5.0V. |
| 6 | FB | input | Feedback pin that the LT8606 regulates to 0.778V, connected to the feedback resistor divider tap. |
| 7 | TR/SS | passive | Output tracking and soft-start pin (MSOP only) with an internal 2µA pull-up from INTVCC, where a voltage below 0.778V forces FB to track it and it is pulled to ground through 300Ω during shutdown and fault conditions. |
| 8 | PG | output | Open-drain power good output that stays low until FB is within ±8.5% of the regulation voltage with no fault conditions, and is valid when VIN is above 3.2V and EN/UV is high. |
| 9 | VIN | power_in | Supplies the internal circuitry and topside power switch with an absolute maximum rating of 42V, and must be locally bypassed with the input capacitor placed close to the VIN pins. |
| 10 | EN/UV | input | Shuts down the LT8606 when low and enables it when high, with a hysteretic threshold of 1.05V rising and 1.00V falling that can be used to program VIN undervoltage lockout. |
| 11 | GND | power_in | Exposed pad that is the ground connection, must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10-EP |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 2.5 | 3 | 3.2 | V | 3 | ||
| VIN Quiescent Current | IQ | 1 | 5 | µA | VEN/UV = 0V | 3 | |
| VIN Quiescent Current | IQ | 1.7 | 12 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V or LT8606 DFN, VIN ≤ 36V | 3 | |
| VIN Current in Regulation | 56 | 90 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 100µA | 3 | ||
| VIN Current in Regulation | 500 | 700 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 1mA | 3 | ||
| Feedback Reference Voltage MSOP Package | VFB | 0.774 | 0.778 | 0.782 | V | VIN = 6V, ILOAD = 100mA | 3 |
| Feedback Reference Voltage MSOP Package | VFB | 0.762 | 0.778 | 0.798 | V | VIN = 6V, ILOAD = 100mA (over full operating temperature range) | 3 |
| Feedback Voltage Line Regulation | 0.02 | 0.06 | %/V | VIN = 4.0V to 40V (over full operating temperature range) | 3 | ||
| Feedback Pin Input Current | IFB | -20 | 20 | nA | VFB = 1V | 3 | |
| Minimum On-Time | tON(MIN) | 35 | 65 | ns | ILOAD = 300mA, SYNC = 0V or LT8606 DFN | 3 | |
| Minimum On-Time | tON(MIN) | 35 | 60 | ns | ILOAD = 300mA, SYNC = 1.9V or LT8606B DFN | 3 | |
| Minimum Off Time | tOFF(MIN) | 93 | 130 | ns | ILOAD = 300mA | 3 | |
| Oscillator Frequency MSOP Package | fSW | 155 | 200 | 245 | kHz | RT = 221k, ILOAD = 250mA | 3 |
| Oscillator Frequency MSOP Package | fSW | 640 | 700 | 760 | kHz | RT = 60.4k, ILOAD = 250mA | 3 |
| Oscillator Frequency MSOP Package | fSW | 1.9 | 2 | 2.1 | MHz | RT = 18.2k, ILOAD = 250mA | 3 |
| Top Power NMOS Current Limit MSOP Package | ILIM | 0.65 | 0.9 | 1.15 | A | Duty cycle 0 (over full operating temperature range) | 3 |
| SW Leakage Current | ISW | 5 | µA | VIN = 36V | 3 | ||
| EN/UV Pin Threshold | VEN/UV | 0.99 | 1.05 | 1.11 | V | EN/UV Rising (over full operating temperature range) | 3 |
| EN/UV Pin Current | IEN/UV | -20 | 20 | nA | VEN/UV = 2V | 3 | |
| PG Upper Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Rising (over full operating temperature range) | 3 | |
| PG Lower Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Falling (over full operating temperature range) | 3 | |
| PG Leakage | IPG | -200 | 200 | nA | VPG = 42V | 3 | |
| PG Pull-Down Resistance | RPG | 550 | 1200 | Ω | VPG = 0.1V | 3 | |
| Sync Low Input Voltage MSOP Only | VSYNC(LOW) | 0.4 | 0.9 | V | MSOP Only (over full operating temperature range) | 3 | |
| Sync High Input Voltage MSOP Only | VSYNC(HIGH) | 2.7 | 3.2 | V | INTVCC = 3.5V, MSOP Only (over full operating temperature range) | 3 | |
| TR/SS Source Current MSOP Only | ITR/SS | 1 | 2 | 3 | µA | MSOP Only (over full operating temperature range) | 3 |
| TR/SS Pull-Down Resistance MSOP Only | RTR/SS | 300 | 900 | Ω | Fault Condition, TR/SS = 0.1V, MSOP Only | 3 | |
| Spread Spectrum Modulation Frequency | fSS | 0.5 | 3 | 6 | kHz | VSYNC = 3.3V, MSOP Only | 3 |
| Absolute Maximum VIN, EN/UV, PG | 42 | V | VIN, EN/UV, PG pins | 2 | |||
| Absolute Maximum FB, TR/SS | 4 | V | FB, TR/SS pins | 2 | |||
| Absolute Maximum SYNC Voltage | 6 | V | SYNC pin | 2 | |||
| Operating Junction Temperature Range E grade | TJ | -40 | 125 | °C | LT8606E | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Thermal Resistance Junction-to-Ambient MSE package | θJA | 40 | °C/W | MSE (10-lead MSOP) package | 2 |
CAD (KiCad official)
- Symbol:
LT8606EMSE#PBF - Footprint:
Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm - 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files:
lt8606emse-pbf-etched.step/lt8606emse-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8606emse-pbf.step/lt8606emse-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (24 pp, sha256
cfaa3e87d6a68cc5, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).