main
Ray Publish 0.1.0 a4b07a2

LT8550EUKG#PBF

Analog Devices · DC-DC Converters · QFN-52-EP(7x8)

LT8550EUKG#PBF from Analog Devices, in a QFN-52-EP(7x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BG4 output Bottom gate driver output for the bottom N-channel MOSFET of phase 4; it swings from ground to REG.
2 BG3 output Bottom gate driver output for the bottom N-channel MOSFET of phase 3; it swings from ground to REG.
3 REG power_out Output of the REG LDO that powers the gate drivers; decouple to ground with a minimum 4.7µF low ESR ceramic capacitor.
4 SW3 passive Switch node of phase 3; it swings from a diode drop below ground to VIN.
5 TG3 output Top gate driver output of a floating driver with a swing equal to REG superimposed on the phase 3 switch node voltage.
6 BST3 power_out Boosted floating driver supply for phase 3; it swings from a diode drop below REG up to VIN + REG.
7 BST2 power_out Boosted floating driver supply for phase 2; it swings from a diode drop below REG up to VIN + REG.
8 TG2 output Top gate driver output of a floating driver with a swing equal to REG superimposed on the phase 2 switch node voltage.
9 SW2 passive Switch node of phase 2; it swings from a diode drop below ground to VIN.
10 BG2 output Bottom gate driver output for the bottom N-channel MOSFET of phase 2; it swings from ground to REG.
11 BG1 output Bottom gate driver output for the bottom N-channel MOSFET of phase 1; it swings from ground to REG.
12 BGBUF output Logic output pulled up to REG when BGSH is high and pulled down to ground when BGSH is low; leave floating on a slave LT8550.
13 TGBUF output On a master LT8550 it is pulled up to REG when (TGSH-TGSL) is high and pulled down to ground when low; leave floating on a slave.
14 BST1 power_out Boosted floating driver supply for phase 1; it swings from a diode drop below REG up to VIN + REG.
15 TG1 output Top gate driver output of a floating driver with a swing equal to REG superimposed on the phase 1 switch node voltage.
16 SW1 passive Switch node of phase 1; it swings from a diode drop below ground to VIN.
17 TGSR input Rail of the primary channel top gate sense circuit; connect to the primary top gate driver boost node on a master or to REG on a slave.
18 TGSH input Input of the primary channel top gate sense circuit; connect to the primary top MOSFET gate on a master or to the master TGBUF on a slave.
19 TGSL input Lower rail of the primary channel top gate sense circuit; connect to the primary top MOSFET source on a master or to ground on a slave.
20 CLK2 bidirectional Clock pin used to synchronize the primary channel to all other channels.
21 CLK1 bidirectional Clock pin used to synchronize the primary channel to all other channels.
22 BGSH input Logic input of the primary channel bottom gate sense circuit; connect to the primary bottom MOSFET gate on a master or to the master BGBUF on a slave.
23 SYNC input Drive with an external clock to synchronize the switching frequency; the clock high level must exceed 1.2V and the low level must be below 0.8V, and driving below 0.8V reverts to the internal clock.
24 PHS2 input Three-level phase selection pin that sets switching frequency and channel phase with PHS1, PHS3 and RT/MS; it can be floated (add 1nF to ground), set to REG or set to ground.
25 PHS1 input Three-level phase selection pin that sets switching frequency and channel phase with PHS2, PHS3 and RT/MS; it can be floated (add 1nF to ground), set to REG or set to ground.
26 RT/MS passive Timing resistor and master/slave select pin; a resistor to ground sets a master LT8550 and a connection to REG sets a slave LT8550.
27 ILIM input Three-level maximum current sense voltage programming pin; ground, REG or floating sets 30mV, 60mV or 90mV, and a floating pin needs a 1nF cap to ground.
28 ENOUT bidirectional On a master LT8550 it is an open-drain logic output; on a slave LT8550 it is an input.
29 VCC power_in Power supply for control circuits; decouple to ground with a minimum 1µF low ESR ceramic capacitor and connect to REG through a 1Ω resistor.
30 MODE input Stage shedding selection pin; connecting it to GND disables the stage shedding feature.
31 SHDN input Shutdown pin; drive below 0.3V to disable the chip and above 1.2V (typical) to activate it, and do not float this pin.
32 IAMPN passive On a master LT8550 connect to local ground; on a slave LT8550 connect to the master LT8550 IAMPN.
33 IAMPP bidirectional On a master LT8550 it is the buffered output of the primary channel current sense amplifier; on a slave it is an input, and all IAMPP pins are connected together.
34 ISP passive Primary channel current sense amplifier (+) input, normally connected to the DCR sensing network or current sense resistor; used only on a master and grounded on a slave.
35 ISN passive Primary channel current sense amplifier (-) input, normally connected to the DCR sensing network or current sense resistor; used only on a master and grounded on a slave.
36 ISP2 passive Expanded channel current sense amplifier (+) input, normally connected to the DCR sensing network or current sense resistor.
37 ISN2 passive Expanded channel current sense amplifier (-) input, normally connected to the DCR sensing network or current sense resistor.
38 ISP4 passive Expanded channel current sense amplifier (+) input, normally connected to the DCR sensing network or current sense resistor.
39 ISN4 passive Expanded channel current sense amplifier (-) input, normally connected to the DCR sensing network or current sense resistor.
40 REGSNS input REG LDO voltage sense pin, connected to the primary channel gate driver power supply pin.
41 PHS3 input Phase select pin that sets switching frequency and channel phase with PHS1, PHS2 and RT/MS; it connects to REG or ground.
42 NC unconnected No connection; leave floating or connect to any adjacent pin.
43 ISN1 passive Expanded channel current sense amplifier (-) input, normally connected to the DCR sensing network or current sense resistor.
44 ISP1 passive Expanded channel current sense amplifier (+) input, normally connected to the DCR sensing network or current sense resistor.
45 ISP3 passive Expanded channel current sense amplifier (+) input, normally connected to the DCR sensing network or current sense resistor.
46 ISN3 passive Expanded channel current sense amplifier (-) input, normally connected to the DCR sensing network or current sense resistor.
47 REGIS input REG LDO current sense pin, connected to the external PMOS source side.
48 REGDRV output Gate driver output for the REG LDO, connected to the external PMOS gate.
49 VIN power_in Input supply pin that must be locally bypassed to ground; the VIN operating voltage range is 3.6V minimum to 80V maximum.
50 SW4 passive Switch node of phase 4; it swings from a diode drop below ground to VIN.
51 TG4 output Top gate driver output of a floating driver with a swing equal to REG superimposed on the phase 4 switch node voltage.
52 BST4 power_out Boosted floating driver supply for phase 4; it swings from a diode drop below REG up to VIN + REG.
53 GND power_in Exposed pad ground; tie directly to the local ground plane and solder it to the PCB.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package QFN-52-EP(7x8)
Category Power Supply Chip
Pins 53

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN Operating Voltage Range VIN 3.6 80 V For Min Spec VCC, REG = 0V 3
VCC Undervoltage Lockout 3.3 3.55 3.8 V VCC Falling, REG = VCC 3
SHDN Input Voltage High 1.05 1.15 1.25 V SHDN Falling 3
SHDN Input Voltage Low 0.3 V Device Disabled, Low Quiescent Current, VCC = 3V, REG = 3V 3
SHDN Pin Bias Current 0 1 µA VSHDN = 3V 3
SHDN Pin Bias Current 8.5 20 µA VSHDN = 12V 3
MODE Low Falling Threshold 0.5 V Slave LT8550 3
MODE High Rising Threshold 4.5 V Slave LT8550 3
ENOUT Leakage Current 0.2 1 µA ENOUT = 5V, REG, VCC = 3V 3
Maximum Positive Current Sense Voltage ISPn-ISNn 27 30 32.5 mV ILIM = 0V, ISNn = 12V, ISPn Rising 3
Maximum Positive Current Sense Voltage ISPn-ISNn 56 60 64 mV ILIM = REG, ISNn = 12V, ISPn Rising 3
Maximum Positive Current Sense Voltage ISPn-ISNn 84.5 90 95.5 mV ILIM = Float, ISNn = 12V, ISPn Rising 3
Maximum Negative Current Sense Voltage ISNn-ISPn 26.5 30 33 mV ILIM = 0V, ISNn = 12V, ISPn Falling 3
Maximum Negative Current Sense Voltage ISNn-ISPn 55.5 60 64.5 mV ILIM = REG, ISNn = 12V, ISPn Falling 3
Maximum Negative Current Sense Voltage ISNn-ISPn 84 90 96 mV ILIM = Float, ISNn = 12V, ISPn Falling 3
ISP, ISN Common Mode Operating Voltage Range 0 80 V 3
ISPn, ISNn Common Mode Operating Voltage Range 0 80 V 3
ILIM High Rising Threshold 4.65 V 3
ILIM Low Falling Threshold 0.3 V 3
IAMPP Output Voltage 2.33 2.4 2.47 V (ISP-ISN) = 30mV, ILIM = 0V, Master LT8550, ISN = 12V 3
IAMPP Output Voltage 1.33 1.4 1.47 V (ISP-ISN) = 0mV, ILIM = 0V, Master LT8550, ISN = 12V 3
IAMPP Output Voltage 0.33 0.4 0.47 V (ISP-ISN) = -30mV, ILIM = 0V, Master LT8550, ISN = 12V 3
IAMPP Output Voltage 1.35 1.4 1.45 V (ISP-ISN) = 0mV, ILIM = REG, Master LT8550, ISN = 12V 3
IAMPP Output Voltage 0.34 0.4 0.46 V (ISP-ISN) = -60mV, ILIM = REG, Master LT8550, ISN = 12V 3
(ISPn-ISNn) Voltage In Regulation 21.25 26.75 mV IAMPP = 2.20V, IAMPN = 0V, ILIM = 0V, ISNn = 12V 4
(ISPn-ISNn) Voltage In Regulation -26.75 -21.25 mV IAMPP = 0.60V, IAMPN = 0V, ILIM = 0V, ISNn = 12V 4
(ISPn-ISNn) Voltage In Regulation 45 51 mV IAMPP = 2.20V, IAMPN = 0V, ILIM = REG, ISNn = 12V 4
(ISPn-ISNn) Voltage In Regulation -51 -45 mV IAMPP = 0.60V, IAMPN = 0V, ILIM = REG, ISNn = 12V 4
(ISPn-ISNn) Voltage In Regulation 67.25 76.75 mV IAMPP = 2.20V, IAMPN = 0V, ILIM = Float, ISNn = 12V 4
(ISPn-ISNn) Voltage In Regulation -76.75 -67.25 mV IAMPP = 0.60V, IAMPN = 0V, ILIM = Float, ISNn = 12V 4
IAMPP Sourcing Current Limit 250 µA (ISP-ISN) = 0mV, Master LT8550 4
IAMPP Sinking Current Limit 60 µA (ISP-ISN) = 0mV, Master LT8550 4
Mismatch Between (ISPn-ISNn) and Master (ISP-ISN) -6 6 % ILIM = REG 4
Mismatch Between (ISPn-ISNn) and Master (ISP-ISN) -10 10 % ILIM = 0V 4
CLK1 Frequency 900 1000 1100 kHz RT/MS = 24.3kΩ, Master LT8550 4
CLK1 Frequency 236 250 264 kHz RT/MS = 100 kΩ, Master LT8550 4
CLK1 Frequency 90 100 110 kHz RT/MS = 249kΩ, Master LT8550 4
Switching Frequency Range 100 1000 kHz Free-Running 4
Switching Frequency Range 125 1000 kHz Synchronizing 4
SYNC High Level for Synchronization 1.2 V 4
SYNC Low Level for Synchronization 0.8 V 4
REG Voltage 4.9 5.1 5.3 V REGSNS = 5V, IAMPN = 0V, ILOAD = 45mA 4
Operating Junction Temperature Range TJ -40 125 °C LT8550E 2
Storage Temperature Range -65 150 °C 2
SW1/2/3/4 Voltage 80 V Note 5 2
Junction-to-Ambient Thermal Resistance θJA 31 °C/W 2
Junction-to-Case Thermal Resistance θJC 2 °C/W 2

CAD (KiCad official)

  • Symbol: LT8550EUKG#PBF
  • Footprint: Package_DFN_QFN:QFN-52-1EP_7x8mm_P0.5mm_EP5.41x6.45mm
  • 3D model: QFN-52-EP(7x8) (KiCad packages3D, STEP)
  • 3D model files: lt8550eukg-pbf-etched.step / lt8550eukg-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8550eukg-pbf.step / lt8550eukg-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (34 pp, sha256 927be678c96a2256, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF