Generated by kicad-footprint-generator · KiCad file format 20260206
LT8390EUFD#PBF
Analog Devices · DC-DC Converters · QFN-28-EP(4x5)
LT8390EUFD#PBF from Analog Devices, in a QFN-28-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TG1 | output | Buck side top gate drive for the top N-channel MOSFET, swinging from SW1 to BST1. |
| 2 | LSP | input | Positive terminal of the buck side inductor current sense resistor (RSENSE), requiring a Kelvin connection for accurate sensing. |
| 3 | LSN | input | Negative terminal of the buck side inductor current sense resistor (RSENSE), requiring a Kelvin connection for accurate sensing. |
| 4 | VIN | power_in | Input supply that sets buck, buck-boost or boost operation; operates from 4V to 60V and needs at least 1µF ceramic bypass to ground. |
| 5 | INTVCC | power_out | Internal 5V linear regulator output (5.0V typical, 4.85V to 5.15V) that powers control circuitry and gate drivers; bypass with at least 4.7µF ceramic. |
| 6 | EN/UVLO | input | Enable and undervoltage lockout pin; below 0.3V shuts the part down, above 1.233V enables normal operation, and the 1.220V falling threshold sets UVLO. |
| 7 | TEST | input | Factory test pin that must be connected directly to ground for the part to operate properly. |
| 8 | LOADEN | input | Load switch enable input that controls the high side PMOS load switch; tie to VREF or INTVCC if the load switch function is not used. |
| 9 | VREF | power_out | Voltage reference output providing an accurate 2V reference capable of supplying 1mA; bypass with a 0.47µF ceramic capacitor to ground. |
| 10 | CTRL | input | Control input that programs the ISP/ISN current sense threshold; forcing it below 0.3V stops switching and tying it to VREF selects the 100mV full-scale threshold. |
| 11 | ISP | input | Positive terminal of the ISP/ISN current sense resistor (RIS), requiring a Kelvin connection for accurate sensing; input common mode range is 0V to 60V. |
| 12 | ISN | input | Negative terminal of the ISP/ISN current sense resistor (RIS), requiring a Kelvin connection for accurate sensing; input common mode range is 0V to 60V. |
| 13 | ISMON | output | ISP/ISN current sense monitor output that equals ten times V(ISP-ISN) plus a 0.25V offset. |
| 14 | PGOOD | output | Power good open drain output that is pulled low when FB is within ±10% of the final regulation voltage and requires an external pull-up resistor. |
| 15 | SS | passive | Soft-start timer pin with a capacitor to ground (0.1µF recommended) that sets the ramp of FB regulation and a resistor to VREF selecting the short-circuit fault mode. |
| 16 | FB | input | Voltage loop feedback input that regulates to 1.00V; below 0.25V triggers the short-circuit fault mode and above 1.1V turns off all TG and BG gate drives and LOADTG. |
| 17 | VC | passive | Error amplifier output that sets the inductor current comparator threshold and is compensated with an external RC network. |
| 18 | RT | passive | Switching frequency setting pin; a resistor to ground sets the internal oscillator between 150kHz and 650kHz. |
| 19 | SYNC/SPRD | input | Synchronization or spread spectrum pin: ground for internal oscillator frequency, apply a clock for external sync, or tie to INTVCC for ±15% triangle spread spectrum. |
| 20 | LOADTG | output | High side PMOS load switch top gate drive, swinging from the higher of (VOUT-5V) and 1.2V up to VOUT; leave unconnected if not used. |
| 21 | VOUT | power_in | Output supply that sets buck, buck-boost or boost operation regions and serves as the positive rail for LOADTG; rated 0V to 60V and needs at least 1µF ceramic bypass. |
| 22 | TG2 | output | Boost side top gate drive for the top N-channel MOSFET, swinging from SW2 to BST2. |
| 23 | SW2 | passive | Boost side switch node that swings from a Schottky diode voltage drop below ground up to VOUT. |
| 24 | BST2 | passive | Boost side bootstrap floating driver supply with an integrated Schottky diode from INTVCC; it swings to (VOUT + INTVCC) and needs an external capacitor to SW2. |
| 25 | BG2 | output | Boost side bottom gate drive for the bottom N-channel MOSFET, swinging from ground to INTVCC. |
| 26 | BG1 | output | Buck side bottom gate drive for the bottom N-channel MOSFET, swinging from ground to INTVCC. |
| 27 | BST1 | passive | Buck side bootstrap floating driver supply with an integrated Schottky diode from INTVCC; it swings to (VIN + INTVCC) and needs an external capacitor to SW1. |
| 28 | SW1 | passive | Buck side switch node that swings from a Schottky diode voltage drop below ground up to VIN. |
| 29 | GND | power_in | Exposed pad ground that must be soldered directly to the PCB ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-28-EP(4x5) |
| Category | Power Management |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Operating Voltage Range | VIN | 4 | 60 | V | l (full operating temperature range) | 3 | |
| VOUT Voltage Range | VOUT | 0 | 60 | V | l | 3 | |
| INTVCC Regulation Voltage | VINTVCC | 4.85 | 5 | 5.15 | V | IINTVCC = 20mA | 3 |
| INTVCC Current Limit | 80 | 110 | 160 | mA | VINTVCC = 4.5V | 3 | |
| INTVCC Undervoltage Lockout Threshold | 3.44 | 3.54 | 3.64 | V | Falling | 3 | |
| VREF Regulation Voltage | VREF | 1.97 | 2 | 2.03 | V | l; IVREF = 100µA | 3 |
| VREF Current Limit | 2 | 2.5 | 3.2 | mA | VREF = 1.8V | 3 | |
| VREF Undervoltage Lockout Threshold | 1.78 | 1.84 | 1.9 | V | Falling | 3 | |
| EN/UVLO Shutdown Threshold | EN/UVLO | 0.3 | 0.6 | 1 | V | l | 4 |
| EN/UVLO Enable Threshold Falling | EN/UVLO | 1.196 | 1.22 | 1.244 | V | l | 4 |
| EN/UVLO Hysteresis Current | -0.1 | 0 | 0.1 | µA | VEN/UVLO = 0.3V | 4 | |
| EN/UVLO Hysteresis Current | 2.2 | 2.5 | 2.9 | µA | VEN/UVLO = 1.1V | 4 | |
| CTRL Input Bias Current | 0 | 20 | 50 | nA | VCTRL = 0.75V, current out of pin | 4 | |
| CTRL Latch-Off Threshold | 285 | 300 | 315 | mV | l; Falling | 4 | |
| LOADEN Threshold | LOADEN | 1.3 | 1.4 | 1.5 | V | l; Rising | 4 |
| LOADTG On Voltage | V(VOUT-LOADTG) | 4.6 | 5 | 5.6 | V | VOUT = 12V | 4 |
| LOADTG Off Voltage | V(VOUT-LOADTG) | -0.1 | 0 | 0.1 | V | VOUT = 12V | 4 |
| Full Scale Current Regulation | V(ISP-ISN) | 97 | 100 | 103 | mV | l; VCTRL = 2V, VISP = 12V | 4 |
| 1/10th Current Regulation | V(ISP-ISN) | 8 | 10 | 12 | mV | l; VCTRL = 0.35V, VISP = 12V | 4 |
| ISMON Monitor Output | VISMON | 1.2 | 1.25 | 1.3 | V | l; V(ISP-ISN) = 100mV, VISP = 12V/0V | 4 |
| ISMON Monitor Output | VISMON | 0.3 | 0.35 | 0.4 | V | l; V(ISP-ISN) = 10mV, VISP = 12V/0V | 4 |
| ISMON Monitor Output | VISMON | 0.2 | 0.25 | 0.3 | V | l; V(ISP-ISN) = 0mV, VISP = 12V/0V | 4 |
| ISP/ISN Input Common Mode Range | 0 | 60 | V | l | 4 | ||
| FB Regulation Voltage | VFB | 0.985 | 1 | 1.015 | V | l; VC = 1.2V | 4 |
| Maximum Current Sense Threshold (Buck) | V(LSP-LSN) | 35 | 50 | 65 | mV | l; Buck, VFB = 0.8V | 5 |
| Maximum Current Sense Threshold (Boost) | V(LSP-LSN) | 40 | 50 | 60 | mV | l; Boost, VFB = 0.8V | 5 |
| FB Overvoltage Threshold | VFB | 1.08 | 1.1 | 1.12 | V | l; Rising | 5 |
| FB Overvoltage Hysteresis | VFB | 35 | 50 | 65 | mV | l | 5 |
| FB Short Threshold | VFB | 0.24 | 0.25 | 0.26 | V | l; Falling | 5 |
| PGOOD Upper Threshold | 8 | 10 | 12 | % | l; Offset from VFB, rising | 5 | |
| PGOOD Lower Threshold | -12 | -10 | -8 | % | l; Offset from VFB, falling | 5 | |
| SS Pull-Up Current | ISS | 10.5 | 12.5 | 14.5 | µA | VFB = 0.4V, VSS = 0V | 5 |
| SS Pull-Down Current | ISS | 1.05 | 1.25 | 1.45 | µA | VFB = 0.1V, VSS = 2V | 5 |
| Switching Frequency | fSW | 190 | 200 | 210 | kHz | l; VSYNC/SPRD = 0V, RT = 226kΩ | 5 |
| Switching Frequency | fSW | 380 | 400 | 420 | kHz | l; VSYNC/SPRD = 0V, RT = 100kΩ | 5 |
| Switching Frequency | fSW | 570 | 600 | 630 | kHz | l; VSYNC/SPRD = 0V, RT = 59.0kΩ | 5 |
| SYNC Frequency | 150 | 650 | kHz | 5 | |||
| SYNC/SPRD Input Bias Current | -0.1 | 0 | 0.1 | µA | VSYNC/SPRD = 5V | 5 | |
| Highest Spread Spectrum Above Oscillator Frequency | 12.5 | 14.5 | 16.5 | % | VSYNC/SPRD = 5V | 5 | |
| Lowest Spread Spectrum Below Oscillator Frequency | -17.7 | -15.7 | -13.7 | % | VSYNC/SPRD = 5V | 5 | |
| Buck-Boost to Boost Region Transition | VIN/VOUT | 0.73 | 0.75 | 0.77 | VIN/VOUT | 5 | |
| Boost to Buck-Boost Region Transition | VIN/VOUT | 0.83 | 0.85 | 0.87 | VIN/VOUT | 5 | |
| Buck to Buck-Boost Region Transition | VIN/VOUT | 1.16 | 1.18 | 1.2 | VIN/VOUT | 5 | |
| Buck-Boost to Buck Region Transition | VIN/VOUT | 1.31 | 1.33 | 1.35 | VIN/VOUT | 5 | |
| Peak-Buck to Peak-Boost Transition | VIN/VOUT | 0.96 | 0.98 | 1 | VIN/VOUT | 5 | |
| Peak-Boost to Peak-Buck Transition | VIN/VOUT | 1 | 1.02 | 1.04 | VIN/VOUT | 5 | |
| Absolute maximum voltage: VIN, EN/UVLO, VOUT, ISP, ISN | 60 | V | 2 | ||||
| Absolute maximum voltage: ISP-ISN | -1 | 1 | V | 2 | |||
| Absolute maximum voltage: SW1, SW2, LSP, LSN | -6 | 60 | V | 2 | |||
| Absolute maximum voltage: INTVCC, (BST1-SW1), (BST2-SW2) | 6 | V | 2 | ||||
| Absolute maximum voltage: (BST1-LSP), (BST1-LSN) | 6 | V | 2 | ||||
| Absolute maximum voltage: FB, LOADEN, SYNC/SPRD, CTRL, PGOOD | 6 | V | 2 | ||||
| Operating Junction Temperature Range, LT8390E | TJ | -40 | 125 | °C | LT8390E grade | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Thermal resistance, junction-to-ambient (UFD QFN package) | θJA | 43 | °C/W | UFD 28-lead 4mm × 5mm QFN package | 2 | ||
| Thermal resistance, junction-to-case (UFD QFN package) | θJC | 3.4 | °C/W | UFD 28-lead 4mm × 5mm QFN package | 2 |
CAD (KiCad official)
- Symbol:
LT8390EUFD#PBF - Footprint:
Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm - 3D model: QFN-28-EP(4x5) (KiCad packages3D, STEP)
- 3D model files:
lt8390eufd-pbf-etched.step/lt8390eufd-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8390eufd-pbf.step/lt8390eufd-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (32 pp, sha256
bedb46ecab867bbe, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).