3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT8390AIFE#PBF
Analog Devices · DC-DC Controllers · TSSOP-28-EP
LT8390AIFE#PBF from Analog Devices, in a TSSOP-28-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BG1 | output | Buck side bottom gate drive for the buck side bottom N-channel MOSFET, with a voltage swing from ground to INTVCC. |
| 2 | BST1 | passive | Buck side bootstrap floating driver supply with an integrated Schottky diode from INTVCC, needing an external bootstrap capacitor to SW1 and swinging from a diode drop below INTVCC to (VIN + INTVCC). |
| 3 | SW1 | passive | Buck side switch node that swings from a Schottky diode voltage drop below ground up to VIN. |
| 4 | TG1 | output | Buck side top gate drive for the buck side top N-channel MOSFET, with a voltage swing from SW1 to BST1. |
| 5 | LSP | input | Positive terminal of the buck side inductor current sense resistor (RSENSE), requiring a Kelvin connection for accurate current sensing. |
| 6 | LSN | input | Negative terminal of the buck side inductor current sense resistor (RSENSE), requiring a Kelvin connection for accurate current sensing. |
| 7 | VIN | power_in | Input supply pin that must be tied to the power input to determine the buck, buck-boost or boost operating region, locally bypassed to ground with at least 1µF ceramic. |
| 8 | INTVCC | power_out | Internal 5V linear regulator output supplied from VIN that powers the internal control circuitry and gate drivers, locally bypassed to ground with at least 4.7µF ceramic. |
| 9 | EN/UVLO | input | Enable and undervoltage lockout input: below 0.3V the part shuts down with VIN quiescent current below 2µA, above 1.233V it operates normally, with an accurate 1.220V falling threshold and 2.5µA pull-down current for UVLO hysteresis. |
| 10 | TEST | input | Factory test pin that must be connected directly to ground for the part to operate properly. |
| 11 | LOADEN | input | Load switch enable input controlling the high side PMOS load switch; tie to VREF or INTVCC if unused, and forcing it low turns off TG1, TG2 and LOADTG and turns on BG1 and BG2. |
| 12 | VREF | power_out | Voltage reference output providing an accurate 2V reference capable of supplying 1mA, locally bypassed to ground with a 0.47µF ceramic capacitor. |
| 13 | CTRL | input | Control input that programs the ISP/ISN current sense threshold (5mV to 90mV for 0.3V to 1.15V, constant 100mV full scale for VCTRL of 1.35V or more), with switching stopped below 0.3V. |
| 14 | ISP | input | Positive terminal of the ISP/ISN current sense resistor (RIS), requiring a Kelvin connection for accurate current sensing. |
| 15 | ISN | input | Negative terminal of the ISP/ISN current sense resistor (RIS), requiring a Kelvin connection for accurate current sensing. |
| 16 | ISMON | output | ISP/ISN current sense monitor output voltage equal to ten times V(ISP-ISN) plus a 0.25V offset. |
| 17 | PGOOD | output | Power good open-drain output pulled low when FB is within ±10% of the final regulation voltage, requiring an external pull-up resistor. |
| 18 | SS | passive | Soft-start timer pin set by a capacitor to ground charged by an internal 12.5µA pull-up (22nF recommended), where a resistor to VREF selects hiccup (none), latch-off (499kΩ) or keep-running (100kΩ) fault mode. |
| 19 | FB | input | Voltage loop feedback input regulated to 1.00V by the error amplifier, with output short-circuit detected at VFB below 0.25V and overvoltage at VFB above 1.1V turning off TG1, BG1, TG2, BG2 and LOADTG. |
| 20 | VC | output | Error amplifier output that sets the inductor current comparator threshold and is compensated with an external RC network, disconnected from internal loads when LOADEN is low. |
| 21 | RT | passive | Switching frequency setting pin where a resistor to ground sets the internal oscillator frequency from 600kHz to 2MHz. |
| 22 | SYNC/SPRD | input | Frequency synchronization or spread spectrum input: ground for the internal oscillator frequency, apply a clock for external synchronization, or tie to INTVCC for 25% triangle spread spectrum above the internal oscillator frequency. |
| 23 | LOADTG | output | High side PMOS load switch top gate drive, a buffered and inverted version of LOADEN swinging from the higher of (VOUT-5V) and 1.2V up to VOUT, to be left unconnected if unused. |
| 24 | VOUT | power_in | Output supply pin that must be tied to the power output to determine the buck, buck-boost or boost operating region and serves as the positive rail for the LOADTG drive, locally bypassed to ground with at least 1µF ceramic. |
| 25 | TG2 | output | Boost side top gate drive for the boost side top N-channel MOSFET, with a voltage swing from SW2 to BST2. |
| 26 | SW2 | passive | Boost side switch node that swings from a Schottky diode voltage drop below ground up to VOUT. |
| 27 | BST2 | passive | Boost side bootstrap floating driver supply with an integrated Schottky diode from INTVCC, needing an external bootstrap capacitor to SW2 and swinging from a diode drop below INTVCC to (VOUT + INTVCC). |
| 28 | BG2 | output | Boost side bottom gate drive for the boost side bottom N-channel MOSFET, with a voltage swing from ground to INTVCC. |
| 29 | GND | power_in | Exposed pad ground, which must be soldered directly to the ground plane on the PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSSOP-28-EP |
| Category | Power Supply Chip |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Operating Voltage Range | VIN | 4 | 60 | V | 4 | ||
| VOUT Voltage Range | VOUT | 0 | 60 | V | 4 | ||
| INTVCC Regulation Voltage | VINTVCC | 4.85 | 5 | 5.15 | V | IINTVCC = 20mA | 4 |
| INTVCC Current Limit | 110 | 145 | 190 | mA | VINTVCC = 4.5V | 4 | |
| INTVCC Undervoltage Lockout Threshold Falling | 3.44 | 3.54 | 3.64 | V | Falling | 4 | |
| VREF Regulation Voltage | VREF | 1.97 | 2 | 2.03 | V | IVREF = 100µA | 4 |
| VREF Current Limit | 2 | 2.5 | 3.2 | mA | VREF = 1.8V | 4 | |
| VREF Undervoltage Lockout Threshold Falling | 1.78 | 1.84 | 1.9 | V | Falling | 4 | |
| EN/UVLO Shutdown Threshold | 0.3 | 0.6 | 1 | V | 4 | ||
| EN/UVLO Enable Threshold Falling | 1.196 | 1.22 | 1.244 | V | Falling | 4 | |
| CTRL Latch-Off Threshold Falling | 285 | 300 | 315 | mV | Falling | 4 | |
| LOADEN Threshold Rising | 1.3 | 1.4 | 1.5 | V | Rising | 4 | |
| LOADTG On Voltage | V(VOUT-LOADTG) | 4.5 | 5 | 5.5 | V | VOUT = 12V | 4 |
| LOADTG Off Voltage | V(VOUT-LOADTG) | -0.1 | 0 | 0.1 | V | VOUT = 12V | 4 |
| Full Scale Current Regulation | V(ISP-ISN) | 97 | 100 | 103 | mV | VCTRL = 2V, VISP = 12V | 5 |
| 1/10th Current Regulation | V(ISP-ISN) | 8 | 10 | 12 | mV | VCTRL = 0.35V, VISP = 12V | 5 |
| ISMON Monitor Output | VISMON | 1.2 | 1.25 | 1.3 | V | V(ISP-ISN) = 100mV, VISP = 12V/0V | 5 |
| ISP/ISN Input Common Mode Range | 0 | 60 | V | 5 | |||
| FB Regulation Voltage | VFB | 0.985 | 1 | 1.015 | V | VC = 1.2V | 5 |
| VC Standby Leakage Current | -10 | 0 | 10 | nA | VC = 1.2V, VLOADEN = 0V | 5 | |
| Maximum Current Sense Threshold Buck | V(LSP-LSN) | 35 | 50 | 65 | mV | Buck, VFB = 0.8V | 5 |
| Maximum Current Sense Threshold Boost | V(LSP-LSN) | 40 | 50 | 60 | mV | Boost, VFB = 0.8V | 5 |
| FB Overvoltage Threshold Rising | VFB | 1.08 | 1.1 | 1.12 | V | Rising | 5 |
| FB Overvoltage Hysteresis | 35 | 50 | 65 | mV | 5 | ||
| FB Short Threshold Falling | VFB | 0.24 | 0.25 | 0.26 | V | Falling | 5 |
| FB Short Hysteresis | 35 | 50 | 65 | mV | Hysteresis | 5 | |
| PGOOD Upper Threshold Offset from VFB Rising | 8 | 10 | 12 | % | Rising | 5 | |
| PGOOD Lower Threshold Offset from VFB Falling | -12 | -10 | -8 | % | Falling | 5 | |
| SS Pull-Up Current | ISS | 10 | 12.5 | 15 | µA | VFB = 0.4V, VSS = 0V | 5 |
| SS Pull-Down Current | ISS | 1 | 1.25 | 1.5 | µA | VFB = 0.1V, VSS = 2V | 5 |
| Switching Frequency | fSW | 645 | 685 | 725 | kHz | VSYNC/SPRD = 0V, RT = 226kΩ | 6 |
| Switching Frequency | fSW | 1290 | 1360 | 1430 | kHz | VSYNC/SPRD = 0V, RT = 100kΩ | 6 |
| Switching Frequency | fSW | 1900 | 2000 | 2100 | kHz | VSYNC/SPRD = 0V, RT = 59.0kΩ | 6 |
| SYNC Frequency | 600 | 2100 | kHz | 6 | |||
| Highest Spread Spectrum Above Oscillator Frequency | 21 | 23 | 25 | % | VSYNC/SPRD = 5V | 6 | |
| Buck-Boost to Boost Region Transition | VIN/VOUT | 0.73 | 0.75 | 0.77 | 6 | ||
| Boost to Buck-Boost Region Transition | VIN/VOUT | 0.83 | 0.85 | 0.87 | 6 | ||
| Buck to Buck-Boost Region Transition | VIN/VOUT | 1.23 | 1.25 | 1.27 | 6 | ||
| Buck-Boost to Buck Region Transition | VIN/VOUT | 1.31 | 1.33 | 1.35 | 6 | ||
| Peak-Buck to Peak-Boost Region Transition | VIN/VOUT | 0.96 | 0.98 | 1 | 6 | ||
| Peak-Boost to Peak-Buck Region Transition | VIN/VOUT | 1 | 1.02 | 1.04 | 6 | ||
| Input Voltage Absolute Maximum (VIN, EN/UVLO, VOUT, ISP, ISN) | VIN | 60 | V | 2 | |||
| ISP-ISN Differential Voltage | ISP-ISN | -1 | 1 | V | 2 | ||
| SW1, SW2, LSP, LSN Voltage | SW | -6 | 60 | V | 2 | ||
| INTVCC, (BST1-SW1), (BST2-SW2) Voltage | INTVCC | 6 | V | 2 | |||
| (BST1-LSP), (BST1-LSN) Voltage | 6 | V | 2 | ||||
| FB, LOADEN, SYNC/SPRD, CTRL, PGOOD Voltage | 6 | V | 2 | ||||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Operating Junction Temperature Range LT8390AI | TJ | -40 | 125 | °C | LT8390AI | 2 | |
| Junction-to-Ambient Thermal Resistance (FE TSSOP package) | θJA | 30 | °C/W | FE package, 28-lead plastic TSSOP | 2 | ||
| Junction-to-Case Thermal Resistance (FE TSSOP package) | θJC | 5 | °C/W | FE package, 28-lead plastic TSSOP | 2 |
CAD (KiCad official)
- Symbol:
LT8390AIFE#PBF - Footprint:
Package_SO:TSSOP-28-1EP_4.4x9.7mm_P0.65mm_EP2.85x6.7mm - 3D model: TSSOP-28-EP (KiCad packages3D, STEP)
- 3D model files:
lt8390aife-pbf-etched.step/lt8390aife-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8390aife-pbf.step/lt8390aife-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (32 pp, sha256
b3c86e61a1228fd3, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).