main
Ray
Publish 0.1.0
5bbd75f
LT8355IUFDM-1#WPBF
Analog Devices · LED Drivers · QFN-28(4x5)
LT8355IUFDM-1#WPBF from Analog Devices, in a QFN-28(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PWMTG1 | output | High side gate driver for the external series PMOS switch of channel 1, driving the gate between ISP1 - 8.5V and ISP1 (typical); leave open if unused. |
| 2 | ISN1 | input | Kelvin connection to the low side of the channel 1 LED current sense resistor RILED1, which sets 250mV/RILED1 when CTRL1 > 1.5V. |
| 3 | ISP1 | input | Kelvin connection to the high side of the channel 1 LED current sense resistor; if VISP - VISN exceeds about 670mV (typical) switching stops and soft-start resets. |
| 4 | FB1 | input | Channel 1 output voltage feedback pin regulating to 1.2V (typical), with overvoltage at 1.26V and shorted-LED detection below 300mV (typical). |
| 5 | VC1 | passive | Channel 1 internal error amplifier compensation node; connect a capacitor or RC network to ground. |
| 6 | CTRL1 | input | Channel 1 analog dimming input that linearly sets RILED1 current as (CTRL1 - 0.5V)/(4RILED1) between 0.5V and 1.5V; tie to VREF or INTVCC for full scale. |
| 7 | FAULT1 | output | Open-drain channel 1 fault indication for short LED, open LED, overvoltage and overcurrent; pull up through 100k to a supply below 15V. |
| 8 | CTRL2 | input | Channel 2 analog dimming input that together with IADJ2 sets RILED2 current as [(CTRL2 - 0.48V)•(IADJ2 - 0.5V) - 0.02V]/(4RILED2) for voltages between 0.5V and 1.5V. |
| 9 | IADJ2 | input | Channel 2 second analog dimming input multiplying with CTRL2 to set RILED2 current when between 0.5V and 1.5V; tie to VREF or INTVCC for full scale. |
| 10 | PWM1 | input | Channel 1 PWM dimming control: analog 0.5V to 1.5V selects the internal exponential duty ratio, or an external PWM signal above 1.6V / below 0.4V; tie to INTVCC or VREF if unused. |
| 11 | PWM2 | input | Channel 2 PWM dimming control: analog 0.5V to 1.5V selects the internal exponential duty ratio, or an external PWM signal above 1.6V / below 0.4V; tie to INTVCC or VREF if unused. |
| 12 | RT | passive | Connect a resistor to ground to set the switching and PWM dimming frequency; connect nothing but a resistor to this pin. |
| 13 | FAULT2 | output | Open-drain channel 2 fault indication for short LED, open LED, overvoltage and overcurrent; pull up through 100k to a supply below 15V. |
| 14 | VREF | power_out | 2V (typical) reference output supplying a maximum of 2.5mA at room temperature; bypass with 1µF if needed, leave floating if unused. |
| 15 | EN/UVLO | input | Enable and undervoltage lockout input with 1.25V (typical) falling threshold and about 60mV hysteresis; minimum Thevenin equivalent resistance 20k. |
| 16 | VIN | power_in | Input supply pin, 5V to 60V operating range, must be locally bypassed. |
| 17 | VC2 | passive | Channel 2 internal error amplifier compensation node; connect a capacitor or RC network to ground. |
| 18 | FB2 | input | Channel 2 output voltage feedback pin regulating to 1.2V (typical), with overvoltage at 1.26V and shorted-LED detection below 300mV (typical). |
| 19 | ISP2 | input | Kelvin connection to the high side of the channel 2 LED current sense resistor; if VISP - VISN exceeds about 670mV (typical) switching stops and soft-start resets. |
| 20 | ISN2 | input | Kelvin connection to the low side of the channel 2 LED current sense resistor RILED2, which sets 250mV/RILED2 when CTRL2 and IADJ2 > 1.5V. |
| 21 | PWMTG2 | output | High side gate driver for the external series PMOS switch of channel 2, driving the gate between ISP2 - 8.5V and ISP2 (typical); leave open if unused. |
| 22 | INTVCC | power_out | Internal circuit supply, 7.5V typical; requires at least 2.2µF (4.7µF recommended) to ground and is not intended to power external loads. |
| 23 | GATE2 | output | Gate driver for the channel 2 external NMOS power switch whose source connects to the switch current sense resistor. |
| 24 | SENSEP2 | input | Kelvin connection to the positive side of the channel 2 grounded switch current sense resistor. |
| 25 | SENSEN2 | input | Kelvin connection to the negative side of the channel 2 switch current sense resistor. |
| 26 | SENSEN1 | input | Kelvin connection to the negative side of the channel 1 switch current sense resistor. |
| 27 | SENSEP1 | input | Kelvin connection to the positive side of the channel 1 grounded switch current sense resistor. |
| 28 | GATE1 | output | Gate driver for the channel 1 external NMOS power switch whose source connects to the switch current sense resistor. |
| 29 | GND | power_in | Exposed pad ground, must be soldered directly to the PCB ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-28(4x5) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Supply Range | VIN | 5 | 60 | V | full operating temperature range | 2 | |
| Input (VIN) Shutdown Current | 0.1 | 1 | µA | EN/UVLO = 0.3V | 2 | ||
| Input (VIN) Shutdown Current | 12 | 20 | µA | EN/UVLO = 1.1V, EN/UVLO Rising | 2 | ||
| EN/UVLO Shutdown Threshold | 1.15 | 1.25 | 1.35 | V | EN/UVLO Falling | 2 | |
| INTVCC Regulation Voltage | 7.35 | 7.5 | 7.65 | V | PWM1,2 = 0V, IINTVCC = 1mA, 12V < VIN < 60V | 3 | |
| INTVCC Line Regulation | 0.75 | 3 | mV/V | PWM1,2 = 0V, 10 < VIN < 60V | 3 | ||
| INTVCC Load Regulation | 2.25 | 4.5 | mV/mA | PWM1,2 = 0V, 1mA < IINTVCC < 30mA | 3 | ||
| INTVCC Current Limit | 110 | 140 | 170 | mA | PWM1,2 = 0V, VIN = 12V, INTVCC = 7V | 3 | |
| INTVCC Current Limit | 30 | 45 | 60 | mA | PWM1,2 = 0V, VIN = 60V, INTVCC = 7V | 3 | |
| VREF Voltage | 1.97 | 2 | 2.02 | V | IVREF = 0.5mA | 3 | |
| VREF Load Regulation | 5 | 8 | mV/mA | IVREF = 0.1mA to 1mA | 3 | ||
| VREF Current Limit | 2.5 | 3.2 | 4 | mA | VREF = 1.8V | 3 | |
| ISP, ISN Common Mode Voltage Range | 0 | 110 | V | 3 | |||
| LED Current Sense Threshold (VISP, VISN) | 245 | 250 | 255 | mV | CTRL1,2 = 2V, IADJ2 = 2V (100%), ISP1,2 = 100V | 3 | |
| LED Current Sense Threshold (VISP, VISN) | 120 | 125 | 130 | mV | CTRL1,2 = 1V, IADJ2 = 2V (50%), ISP1,2 = 100V | 3 | |
| LED Current Sense Threshold (VISP, VISN) | 20 | 25 | 30 | mV | CTRL1,2 = 0.6V, IADJ2 = 2V (10%), ISP1,2 = 100V | 3 | |
| LED Current Sense Threshold (VISP, VISN) | 240 | 250 | 260 | mV | CTRL1,2 = 2V, IADJ2 = 2V (100%), ISN1,2 = 0V | 3 | |
| LED2 Current Sense Threshold (VISP2, VISN2) | 118 | 125 | 134 | mV | CTRL2 = 2V, IADJ2 = 1V (50%), ISP = 100V | 3 | |
| SENSE Current Limit Threshold (SENSEP − SENSEN) | 95 | 108 | 120 | mV | 50% Duty Cycle at GATE (Note 6) | 3 | |
| CTRL Off Threshold (Falling) | 285 | 310 | 335 | mV | 3 | ||
| ISP, ISN Pin Current (Combined), Standby | 20 | 25 | µA | PWM1,2 = 0V, ISP1,2 = 100V (Standby) | 3 | ||
| FB Regulation Voltage | VFB | 1.182 | 1.2 | 1.218 | V | CTRL1,2 = 2V, IADJ2 = 2V | 3 |
| FB Regulation Voltage | VFB | 1.176 | 1.2 | 1.224 | V | CTRL1,2 = 2V, IADJ2 = 2V, full operating temperature range | 3 |
| Programmed Switching Frequency (fSW1, Channel 1) | fSW1 | 1800 | 1950 | 2100 | kHz | RT = 9.09kΩ | 3 |
| Programmed Switching Frequency (fSW1, Channel 1) | fSW1 | 380 | 400 | 420 | kHz | RT = 51.1kΩ | 3 |
| Programmed Switching Frequency (fSW1, Channel 1) | fSW1 | 96 | 102 | 108 | kHz | RT = 215kΩ | 3 |
| Minimum Off-Time | 30 | 60 | 85 | ns | RT = 9.09kΩ | 3 | |
| Minimum Off-Time | 75 | 120 | 165 | ns | RT = 51.1kΩ | 3 | |
| Minimum Off-Time | 100 | 170 | 240 | ns | RT = 215kΩ | 3 | |
| PWMTG ON Voltage (VISP, VPWMTG) | 7.5 | 8.5 | 9.5 | V | VISP1,2 = 100V | 4 | |
| PWMTG OFF Voltage (VISP, VPWMTG) | 0 | 0.3 | V | VISP1,2 = 100V | 4 | ||
| FB LED Open Threshold | 1.116 | 1.14 | 1.164 | V | VISP1,2 = VISN 1,2, FB Rising | 4 | |
| FB Overvoltage Threshold | 1.235 | 1.26 | 1.285 | V | FB1,2 Rising | 4 | |
| LED Overcurrent Protection Threshold (VISP, VISN) | 580 | 670 | 760 | mV | 4 | ||
| Input (VIN) Quiescent Current | 3 | mA | PWM1,2 = 0V | 2 | |||
| EN/UVLO Rising Hysteresis | 60 | mV | EN/UVLO Rising | 2 | |||
| INTVCC Undervoltage Lockout Threshold | 4.3 | V | PWM1,2 = 0V, INTVCC Falling | 3 | |||
| Minimum On-Time | 100 | ns | CGATE1,2 = 3.3nF | 4 | |||
| ISP1, ISP2, ISN1, ISN2 | 120 | V | 2 | ||||
| ISP1, ISN1, ISP2, ISN2 | -1 | 1 | V | Note 9 | 2 | ||
| CTRL1, CTRL2, FB1, FB2 | 15 | V | 2 | ||||
| FAULT1, FAULT2, IADJ2, PWM1, PWM2 | 15 | V | 2 | ||||
| INTVCC | 8 | V | VIN + 0.3V, 8V | 2 | |||
| SENSEP1, SENSEN1, SENSEP2, SENSEN2 | -0.5 | 0.5 | V | 2 | |||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | LT8355I-1 | 2 | |
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Junction-to-Ambient Thermal Resistance | θJA | 43 | °C/W | UFDM package | 2 | ||
| Junction-to-Case Thermal Resistance | θJC | 3.4 | °C/W | UFDM package | 2 |
CAD (KiCad official)
- Symbol:
LT8355IUFDM-1#WPBF - Footprint:
Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm - 3D model: QFN-28(4x5) (KiCad packages3D, STEP)
- 3D model files:
lt8355iufdm-1-wpbf-etched.step/lt8355iufdm-1-wpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8355iufdm-1-wpbf.step/lt8355iufdm-1-wpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (31 pp, sha256
e789002dd440f861, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT8355IUFDM-1#WPBF
**Analog Devices** · LED Drivers · QFN-28(4x5)
LT8355IUFDM-1#WPBF from Analog Devices, in a QFN-28(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PWMTG1 | output | High side gate driver for the external series PMOS switch of channel 1, driving the gate between ISP1 - 8.5V and ISP1 (typical); leave open if unused. |
| 2 | ISN1 | input | Kelvin connection to the low side of the channel 1 LED current sense resistor RILED1, which sets 250mV/RILED1 when CTRL1 > 1.5V. |
| 3 | ISP1 | input | Kelvin connection to the high side of the channel 1 LED current sense resistor; if VISP - VISN exceeds about 670mV (typical) switching stops and soft-start resets. |
| 4 | FB1 | input | Channel 1 output voltage feedback pin regulating to 1.2V (typical), with overvoltage at 1.26V and shorted-LED detection below 300mV (typical). |
| 5 | VC1 | passive | Channel 1 internal error amplifier compensation node; connect a capacitor or RC network to ground. |
| 6 | CTRL1 | input | Channel 1 analog dimming input that linearly sets RILED1 current as (CTRL1 - 0.5V)/(4RILED1) between 0.5V and 1.5V; tie to VREF or INTVCC for full scale. |
| 7 | FAULT1 | output | Open-drain channel 1 fault indication for short LED, open LED, overvoltage and overcurrent; pull up through 100k to a supply below 15V. |
| 8 | CTRL2 | input | Channel 2 analog dimming input that together with IADJ2 sets RILED2 current as [(CTRL2 - 0.48V)•(IADJ2 - 0.5V) - 0.02V]/(4RILED2) for voltages between 0.5V and 1.5V. |
| 9 | IADJ2 | input | Channel 2 second analog dimming input multiplying with CTRL2 to set RILED2 current when between 0.5V and 1.5V; tie to VREF or INTVCC for full scale. |
| 10 | PWM1 | input | Channel 1 PWM dimming control: analog 0.5V to 1.5V selects the internal exponential duty ratio, or an external PWM signal above 1.6V / below 0.4V; tie to INTVCC or VREF if unused. |
| 11 | PWM2 | input | Channel 2 PWM dimming control: analog 0.5V to 1.5V selects the internal exponential duty ratio, or an external PWM signal above 1.6V / below 0.4V; tie to INTVCC or VREF if unused. |
| 12 | RT | passive | Connect a resistor to ground to set the switching and PWM dimming frequency; connect nothing but a resistor to this pin. |
| 13 | FAULT2 | output | Open-drain channel 2 fault indication for short LED, open LED, overvoltage and overcurrent; pull up through 100k to a supply below 15V. |
| 14 | VREF | power_out | 2V (typical) reference output supplying a maximum of 2.5mA at room temperature; bypass with 1µF if needed, leave floating if unused. |
| 15 | EN/UVLO | input | Enable and undervoltage lockout input with 1.25V (typical) falling threshold and about 60mV hysteresis; minimum Thevenin equivalent resistance 20k. |
| 16 | VIN | power_in | Input supply pin, 5V to 60V operating range, must be locally bypassed. |
| 17 | VC2 | passive | Channel 2 internal error amplifier compensation node; connect a capacitor or RC network to ground. |
| 18 | FB2 | input | Channel 2 output voltage feedback pin regulating to 1.2V (typical), with overvoltage at 1.26V and shorted-LED detection below 300mV (typical). |
| 19 | ISP2 | input | Kelvin connection to the high side of the channel 2 LED current sense resistor; if VISP - VISN exceeds about 670mV (typical) switching stops and soft-start resets. |
| 20 | ISN2 | input | Kelvin connection to the low side of the channel 2 LED current sense resistor RILED2, which sets 250mV/RILED2 when CTRL2 and IADJ2 > 1.5V. |
| 21 | PWMTG2 | output | High side gate driver for the external series PMOS switch of channel 2, driving the gate between ISP2 - 8.5V and ISP2 (typical); leave open if unused. |
| 22 | INTVCC | power_out | Internal circuit supply, 7.5V typical; requires at least 2.2µF (4.7µF recommended) to ground and is not intended to power external loads. |
| 23 | GATE2 | output | Gate driver for the channel 2 external NMOS power switch whose source connects to the switch current sense resistor. |
| 24 | SENSEP2 | input | Kelvin connection to the positive side of the channel 2 grounded switch current sense resistor. |
| 25 | SENSEN2 | input | Kelvin connection to the negative side of the channel 2 switch current sense resistor. |
| 26 | SENSEN1 | input | Kelvin connection to the negative side of the channel 1 switch current sense resistor. |
| 27 | SENSEP1 | input | Kelvin connection to the positive side of the channel 1 grounded switch current sense resistor. |
| 28 | GATE1 | output | Gate driver for the channel 1 external NMOS power switch whose source connects to the switch current sense resistor. |
| 29 | GND | power_in | Exposed pad ground, must be soldered directly to the PCB ground plane. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-28(4x5) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 29 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Supply Range | VIN | 5 | | 60 | V | full operating temperature range | 2 |
| Input (VIN) Shutdown Current | | | 0.1 | 1 | µA | EN/UVLO = 0.3V | 2 |
| Input (VIN) Shutdown Current | | | 12 | 20 | µA | EN/UVLO = 1.1V, EN/UVLO Rising | 2 |
| EN/UVLO Shutdown Threshold | | 1.15 | 1.25 | 1.35 | V | EN/UVLO Falling | 2 |
| INTVCC Regulation Voltage | | 7.35 | 7.5 | 7.65 | V | PWM1,2 = 0V, IINTVCC = 1mA, 12V < VIN < 60V | 3 |
| INTVCC Line Regulation | | | 0.75 | 3 | mV/V | PWM1,2 = 0V, 10 < VIN < 60V | 3 |
| INTVCC Load Regulation | | | 2.25 | 4.5 | mV/mA | PWM1,2 = 0V, 1mA < IINTVCC < 30mA | 3 |
| INTVCC Current Limit | | 110 | 140 | 170 | mA | PWM1,2 = 0V, VIN = 12V, INTVCC = 7V | 3 |
| INTVCC Current Limit | | 30 | 45 | 60 | mA | PWM1,2 = 0V, VIN = 60V, INTVCC = 7V | 3 |
| VREF Voltage | | 1.97 | 2 | 2.02 | V | IVREF = 0.5mA | 3 |
| VREF Load Regulation | | | 5 | 8 | mV/mA | IVREF = 0.1mA to 1mA | 3 |
| VREF Current Limit | | 2.5 | 3.2 | 4 | mA | VREF = 1.8V | 3 |
| ISP, ISN Common Mode Voltage Range | | 0 | | 110 | V | | 3 |
| LED Current Sense Threshold (VISP, VISN) | | 245 | 250 | 255 | mV | CTRL1,2 = 2V, IADJ2 = 2V (100%), ISP1,2 = 100V | 3 |
| LED Current Sense Threshold (VISP, VISN) | | 120 | 125 | 130 | mV | CTRL1,2 = 1V, IADJ2 = 2V (50%), ISP1,2 = 100V | 3 |
| LED Current Sense Threshold (VISP, VISN) | | 20 | 25 | 30 | mV | CTRL1,2 = 0.6V, IADJ2 = 2V (10%), ISP1,2 = 100V | 3 |
| LED Current Sense Threshold (VISP, VISN) | | 240 | 250 | 260 | mV | CTRL1,2 = 2V, IADJ2 = 2V (100%), ISN1,2 = 0V | 3 |
| LED2 Current Sense Threshold (VISP2, VISN2) | | 118 | 125 | 134 | mV | CTRL2 = 2V, IADJ2 = 1V (50%), ISP = 100V | 3 |
| SENSE Current Limit Threshold (SENSEP − SENSEN) | | 95 | 108 | 120 | mV | 50% Duty Cycle at GATE (Note 6) | 3 |
| CTRL Off Threshold (Falling) | | 285 | 310 | 335 | mV | | 3 |
| ISP, ISN Pin Current (Combined), Standby | | | 20 | 25 | µA | PWM1,2 = 0V, ISP1,2 = 100V (Standby) | 3 |
| FB Regulation Voltage | VFB | 1.182 | 1.2 | 1.218 | V | CTRL1,2 = 2V, IADJ2 = 2V | 3 |
| FB Regulation Voltage | VFB | 1.176 | 1.2 | 1.224 | V | CTRL1,2 = 2V, IADJ2 = 2V, full operating temperature range | 3 |
| Programmed Switching Frequency (fSW1, Channel 1) | fSW1 | 1800 | 1950 | 2100 | kHz | RT = 9.09kΩ | 3 |
| Programmed Switching Frequency (fSW1, Channel 1) | fSW1 | 380 | 400 | 420 | kHz | RT = 51.1kΩ | 3 |
| Programmed Switching Frequency (fSW1, Channel 1) | fSW1 | 96 | 102 | 108 | kHz | RT = 215kΩ | 3 |
| Minimum Off-Time | | 30 | 60 | 85 | ns | RT = 9.09kΩ | 3 |
| Minimum Off-Time | | 75 | 120 | 165 | ns | RT = 51.1kΩ | 3 |
| Minimum Off-Time | | 100 | 170 | 240 | ns | RT = 215kΩ | 3 |
| PWMTG ON Voltage (VISP, VPWMTG) | | 7.5 | 8.5 | 9.5 | V | VISP1,2 = 100V | 4 |
| PWMTG OFF Voltage (VISP, VPWMTG) | | | 0 | 0.3 | V | VISP1,2 = 100V | 4 |
| FB LED Open Threshold | | 1.116 | 1.14 | 1.164 | V | VISP1,2 = VISN 1,2, FB Rising | 4 |
| FB Overvoltage Threshold | | 1.235 | 1.26 | 1.285 | V | FB1,2 Rising | 4 |
| LED Overcurrent Protection Threshold (VISP, VISN) | | 580 | 670 | 760 | mV | | 4 |
| Input (VIN) Quiescent Current | | | 3 | | mA | PWM1,2 = 0V | 2 |
| EN/UVLO Rising Hysteresis | | | 60 | | mV | EN/UVLO Rising | 2 |
| INTVCC Undervoltage Lockout Threshold | | | 4.3 | | V | PWM1,2 = 0V, INTVCC Falling | 3 |
| Minimum On-Time | | | 100 | | ns | CGATE1,2 = 3.3nF | 4 |
| ISP1, ISP2, ISN1, ISN2 | | | | 120 | V | | 2 |
| ISP1, ISN1, ISP2, ISN2 | | -1 | | 1 | V | Note 9 | 2 |
| CTRL1, CTRL2, FB1, FB2 | | | | 15 | V | | 2 |
| FAULT1, FAULT2, IADJ2, PWM1, PWM2 | | | | 15 | V | | 2 |
| INTVCC | | | | 8 | V | VIN + 0.3V, 8V | 2 |
| SENSEP1, SENSEN1, SENSEP2, SENSEN2 | | -0.5 | | 0.5 | V | | 2 |
| Operating Junction Temperature Range | TJ | -40 | | 125 | °C | LT8355I-1 | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| Junction-to-Ambient Thermal Resistance | θJA | | 43 | | °C/W | UFDM package | 2 |
| Junction-to-Case Thermal Resistance | θJC | | 3.4 | | °C/W | UFDM package | 2 |
## CAD (KiCad official)
- Symbol: `LT8355IUFDM-1#WPBF`
- Footprint: `Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm`
- 3D model: QFN-28(4x5) (KiCad packages3D, STEP)
- 3D model files: `lt8355iufdm-1-wpbf-etched.step` / `lt8355iufdm-1-wpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt8355iufdm-1-wpbf.step` / `lt8355iufdm-1-wpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/lt8355-1.pdf) (31 pp, sha256 `e789002dd440f861`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt8355iufdm-1-wpbf-datasheet.pdf)