3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT6300IGN#PBF
Analog Devices · Operational Amplifier · SSOP-16-150mil
LT6300IGN#PBF from Analog Devices, in a SSOP-16-150mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | V- | power_in | Negative supply pin, one of four corner pins (1, 8, 9, 16) tied to the leadframe and electrically connected to V-; absolute maximum supply is ±13.5V (V+ to V-) and the part is specified for ±5V to ±12V. |
| 2 | -IN | input | Inverting input of amplifier A; absolute maximum input current is ±10mA. |
| 3 | +IN | input | Noninverting input of amplifier A; input common-mode range is V+ - 2V to V- + 2V with VCM = 0V tested and CMRR of 83dB typical. |
| 4 | SHDN | input | Shutdown control pin; the driver is shut down and outputs go high impedance when SHDN is less than SHDNREF + 0.4V, and RBIAS between V+ and SHDN sets the quiescent current per amplifier. |
| 5 | SHDNREF | input | Shutdown reference pin, normally grounded, which sets the reference level for the SHDN threshold (SHDN must be below SHDNREF + 0.4V to shut down). |
| 6 | +IN | input | Noninverting input of amplifier B; input common-mode range is V+ - 2V to V- + 2V with VCM = 0V tested and CMRR of 83dB typical. |
| 7 | -IN | input | Inverting input of amplifier B; absolute maximum input current is ±10mA. |
| 8 | V- | power_in | Negative supply pin, one of four corner pins (1, 8, 9, 16) tied to the leadframe and electrically connected to V-; absolute maximum supply is ±13.5V (V+ to V-) and the part is specified for ±5V to ±12V. |
| 9 | V- | power_in | Negative supply pin, one of four corner pins (1, 8, 9, 16) tied to the leadframe and electrically connected to V-; absolute maximum supply is ±13.5V (V+ to V-) and the part is specified for ±5V to ±12V. |
| 10 | OUT | output | Output of amplifier B; sources and sinks at least ±500mA and is short-circuit protected to ground for indefinite duration. |
| 11 | NC | unconnected | No connection. |
| 12 | V+ | power_in | Positive supply pin; absolute maximum supply is ±13.5V (V+ to V-) and the part is specified for ±5V to ±12V. |
| 13 | V+ | power_in | Positive supply pin; absolute maximum supply is ±13.5V (V+ to V-) and the part is specified for ±5V to ±12V. |
| 14 | NC | unconnected | No connection. |
| 15 | OUT | output | Output of amplifier A; sources and sinks at least ±500mA and is short-circuit protected to ground for indefinite duration. |
| 16 | V- | power_in | Negative supply pin, one of four corner pins (1, 8, 9, 16) tied to the leadframe and electrically connected to V-; absolute maximum supply is ±13.5V (V+ to V-) and the part is specified for ±5V to ±12V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | SSOP-16-150mil |
| Category | Operational Amplifier/Comparator |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (V+ to V-) | 13.5 | V | V+ to V-; printed as ±13.5V | 2 | |||
| Input Current | -10 | 10 | mA | printed as ±10mA | 2 | ||
| Operating Temperature Range | -40 | 85 | °C | 2 | |||
| Specified Temperature Range | -40 | 85 | °C | Note 3 | 2 | ||
| Junction Temperature | 150 | °C | 2 | ||||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature | 300 | °C | Soldering, 10 sec | 2 | |||
| Thermal Resistance Junction-to-Ambient | θJA | 70 | 95 | °C/W | Varies with PC board metal on pins 1, 8, 9, 16 (Note 4) | 2 | |
| Input Offset Voltage | VOS | 1 | 5 | mV | 2 | ||
| Input Offset Voltage | VOS | 7.5 | mV | ● full specified temperature range | 2 | ||
| Input Offset Voltage Matching | 0.3 | 5 | mV | 2 | |||
| Input Offset Voltage Matching | 7.5 | mV | ● full specified temperature range | 2 | |||
| Input Offset Voltage Drift | 10 | µV/°C | ● full specified temperature range | 2 | |||
| Input Offset Current | IOS | 100 | 500 | nA | 2 | ||
| Input Offset Current | IOS | 800 | nA | ● full specified temperature range | 2 | ||
| Input Bias Current | IB | -4 | 0.1 | 4 | µA | 2 | |
| Input Bias Current | IB | -6 | 6 | µA | ● full specified temperature range | 2 | |
| Input Bias Current Matching | 100 | 500 | nA | 2 | |||
| Input Bias Current Matching | 800 | nA | ● full specified temperature range | 2 | |||
| Input Resistance | RIN | 5 | 50 | MΩ | ● VCM = (V+, 2V) to (V-+ 2V) | 2 | |
| Common Mode Rejection Ratio | CMRR | 74 | 83 | dB | VCM = (V+, 2V) to (V- + 2V) | 2 | |
| Common Mode Rejection Ratio | CMRR | 66 | dB | ● full specified temperature range | 2 | ||
| Power Supply Rejection Ratio | PSRR | 74 | 88 | dB | VS = ±4V to ±12V | 2 | |
| Power Supply Rejection Ratio | PSRR | 66 | dB | ● full specified temperature range | 2 | ||
| Large-Signal Voltage Gain | AVOL | 63 | 76 | dB | VS = ±12V, VOUT = ±10V, RL = 40Ω | 3 | |
| Large-Signal Voltage Gain | AVOL | 57 | dB | ● full specified temperature range | 3 | ||
| Large-Signal Voltage Gain | AVOL | 60 | 70 | dB | VS = ±5V, VOUT = ±3V, RL = 25Ω | 3 | |
| Large-Signal Voltage Gain | AVOL | 54 | dB | ● full specified temperature range | 3 | ||
| Output Swing | VOUT | 10.7 | 10.9 | ±V | VS = ±12V, RL = 100Ω | 3 | |
| Output Swing | VOUT | 10.5 | ±V | ● full specified temperature range | 3 | ||
| Output Swing | VOUT | 10.4 | 10.7 | ±V | VS = ±12V, IL = 250mA | 3 | |
| Output Swing | VOUT | 10.2 | ±V | ● full specified temperature range | 3 | ||
| Output Swing | VOUT | 3.5 | 3.8 | ±V | VS = ±5V, RL = 25Ω | 3 | |
| Output Swing | VOUT | 3.3 | ±V | ● full specified temperature range | 3 | ||
| Output Swing | VOUT | 3.4 | 3.7 | ±V | VS = ±5V, IL = 250mA | 3 | |
| Output Swing | VOUT | 3.2 | ±V | ● full specified temperature range | 3 | ||
| Maximum Output Current | IOUT | 500 | 1200 | mA | VS = ±12V, RL = 1Ω | 3 | |
| Supply Current per Amplifier | IS | 8 | 10 | 13.5 | mA | VS = ±12V, RBIAS = 24.9k (Note 6) | 3 |
| Supply Current per Amplifier | IS | 6.7 | 15 | mA | ● full specified temperature range | 3 | |
| Supply Current per Amplifier | IS | 2.2 | 3.4 | 5 | mA | VS = ±5V, RBIAS = 24.9k (Note 6) | 3 |
| Supply Current per Amplifier | IS | 1.8 | 5.8 | mA | ● full specified temperature range | 3 | |
| Supply Current in Shutdown | 0.1 | 1 | mA | VSHDN = 0.4V | 3 | ||
| Output Leakage in Shutdown | 0.3 | 1 | mA | VSHDN = 0.4V | 3 | ||
| Channel Separation | 80 | 110 | dB | VS = ±12V, VOUT = ±10V, RL = 40Ω | 3 | ||
| Channel Separation | 77 | dB | ● full specified temperature range | 3 | |||
| Slew Rate | SR | 300 | 600 | V/µs | VS = ±12V, AV = -10, (Note 7) | 3 | |
| Slew Rate | SR | 100 | 200 | V/µs | VS = ±5V, AV = -10, (Note 7) | 3 |
CAD (KiCad official)
- Symbol:
LT6300IGN#PBF - Footprint:
Package_SO:SSOP-16_3.9x4.9mm_P0.635mm - 3D model: SSOP-16-150mil (KiCad packages3D, STEP)
- 3D model files:
lt6300ign-etched.step/lt6300ign-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt6300ign.step/lt6300ign.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (16 pp, sha256
3b7cf0810287ac6d, retrieved 2026-11-11, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).