main
Ray
Publish 0.1.0
54fc9e2
LT3971EMSE#PBF
Analog Devices · DC-DC Converters · MSOP-10-EP
LT3971EMSE#PBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BD | passive | This pin connects to the anode of the boost diode and is normally connected to the output. |
| 2 | BOOST | power_in | This pin provides a drive voltage, higher than the input voltage, to the internal bipolar NPN power switch. |
| 3 | SW | output | This pin is the output of the internal power switch and connects to the inductor, catch diode, and boost capacitor. |
| 4 | VIN | power_in | This pin supplies current to the internal circuitry and power switch and must be locally bypassed; the datasheet gives a wide input range of 4.3V to 38V. |
| 5 | EN | input | The part is in shutdown when this pin is low and active when high; the hysteretic threshold is 1.005V going up and 0.975V going down, and is accurate only when VIN is above 4.3V. |
| 6 | FB | input | The LT3971 regulates this pin to 1.19V, with the feedback resistor divider tap connected here and a phase lead capacitor of typically 10pF between FB and VOUT. |
| 7 | SS | passive | A capacitor between SS and ground slowly ramps up the peak current limit on start-up; the pin is only actively discharged when EN is low, and a 100k series resistor is added for VIN above 25V. |
| 8 | RT | passive | A resistor between RT and ground sets the switching frequency. |
| 9 | PG | output | This open-drain output of an internal comparator remains low until FB is within 9% of the final regulation voltage and is valid when the part is enabled and VIN is above 4.3V. |
| 10 | SYNC | input | This external clock synchronization input is grounded for low-ripple Burst Mode operation at low loads, and tying it to a clock source synchronizes the part with pulse-skipping at low loads, where quiescent current rises to 1.5mA. |
| 11 | GND | power_in | Ground exposed pad that must be soldered to the PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10-EP |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 4 | 4.3 | V | Note 4 | 3 | ||
| Quiescent Current from VIN | IQ | 0.7 | 1.2 | μA | VEN Low | 3 | |
| Quiescent Current from VIN | IQ | 1.7 | 2.7 | μA | VEN High, VSYNC Low | 3 | |
| Quiescent Current from VIN | IQ | 4.5 | μA | VEN High, VSYNC Low, l (over operating temperature range) | 3 | ||
| FB Pin Current | IFB | 0.1 | 12 | nA | VFB = 1.19V, l | 3 | |
| Feedback Voltage | VFB | 1.175 | 1.19 | 1.205 | V | l (over operating temperature range), first printed row | 3 |
| Feedback Voltage | VFB | 1.165 | 1.19 | 1.215 | V | l (over operating temperature range), second printed row, grade not labelled | 3 |
| FB Voltage Line Regulation | 0.0002 | 0.01 | %/V | 4.3V < VIN < 38V (Note 4) | 3 | ||
| Switching Frequency | fSW | 1.6 | 2 | 2.4 | MHz | RT = 11k | 3 |
| Switching Frequency | fSW | 0.8 | 1 | 1.2 | MHz | RT = 35.7k | 3 |
| Switching Frequency | fSW | 160 | 200 | 240 | kHz | RT = 255k | 3 |
| Minimum Switch On Time | tON(MIN) | 80 | ns | 3 | |||
| Minimum Switch Off Time | tOFF(MIN) | 110 | 150 | ns | 3 | ||
| Switch Current Limit | ILIM | 1.8 | 2.4 | 3 | A | 3 | |
| Switch VCESAT | VCESAT | 330 | mV | ISW = 1A | 3 | ||
| Switch Leakage Current | 0.02 | 1 | μA | 3 | |||
| Boost Schottky Forward Voltage | VF | 770 | mV | ISH = 100mA | 3 | ||
| Boost Schottky Reverse Leakage | IR | 0.02 | 1 | μA | VREVERSE = 12V | 3 | |
| Minimum Boost Voltage | 1.4 | 1.8 | V | VIN = 5V, l (Note 3) | 3 | ||
| BOOST Pin Current | 20 | 28 | mA | ISW = 1A, VBOOST = 15V | 3 | ||
| EN Voltage Threshold | 0.95 | 1.01 | 1.07 | V | EN Rising, l | 3 | |
| EN Voltage Hysteresis | 30 | mV | 3 | ||||
| EN Pin Current | 0.2 | 20 | nA | 3 | |||
| LT3971 PG Threshold Offset from VFB | 60 | 100 | 140 | mV | VFB Rising | 3 | |
| LT3971 PG Hysteresis | 20 | mV | 3 | ||||
| PG Leakage | 0.02 | 1 | μA | VPG = 3V | 4 | ||
| PG Sink Current | 300 | 570 | μA | VPG = 0.4V, l | 4 | ||
| SYNC Threshold | 0.6 | 0.8 | 1 | V | 4 | ||
| SYNC Pin Current | 0.1 | nA | 4 | ||||
| SS Source Current | ISS | 0.6 | 1 | 1.6 | μA | VSS = 1V | 4 |
| Input Voltage (EN, VIN) | 38 | V | VIN, EN voltage | 2 | |||
| BOOST Pin Above SW Pin | 30 | V | 2 | ||||
| FB, VOUT, RT, SYNC, SS Voltage | 6 | V | 2 | ||||
| PG, BD Voltage | 30 | V | 2 | ||||
| Boost Diode Current | 1 | A | 2 | ||||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Operating Junction Temperature Range (LT3971E) | -40 | 125 | °C | LT3971E | 2 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 45 | °C/W | MSE 10-lead package | 2 | ||
| Thermal Resistance Junction-to-Case | θJC | 10 | °C/W | MSE 10-lead package | 2 |
CAD (KiCad official)
- Symbol:
LT3971EMSE#PBF - Footprint:
Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm - 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files:
lt3971emse-pbf-etched.step/lt3971emse-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3971emse-pbf.step/lt3971emse-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
cf769206b11377dd, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT3971EMSE#PBF
**Analog Devices** · DC-DC Converters · MSOP-10-EP
LT3971EMSE#PBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BD | passive | This pin connects to the anode of the boost diode and is normally connected to the output. |
| 2 | BOOST | power_in | This pin provides a drive voltage, higher than the input voltage, to the internal bipolar NPN power switch. |
| 3 | SW | output | This pin is the output of the internal power switch and connects to the inductor, catch diode, and boost capacitor. |
| 4 | VIN | power_in | This pin supplies current to the internal circuitry and power switch and must be locally bypassed; the datasheet gives a wide input range of 4.3V to 38V. |
| 5 | EN | input | The part is in shutdown when this pin is low and active when high; the hysteretic threshold is 1.005V going up and 0.975V going down, and is accurate only when VIN is above 4.3V. |
| 6 | FB | input | The LT3971 regulates this pin to 1.19V, with the feedback resistor divider tap connected here and a phase lead capacitor of typically 10pF between FB and VOUT. |
| 7 | SS | passive | A capacitor between SS and ground slowly ramps up the peak current limit on start-up; the pin is only actively discharged when EN is low, and a 100k series resistor is added for VIN above 25V. |
| 8 | RT | passive | A resistor between RT and ground sets the switching frequency. |
| 9 | PG | output | This open-drain output of an internal comparator remains low until FB is within 9% of the final regulation voltage and is valid when the part is enabled and VIN is above 4.3V. |
| 10 | SYNC | input | This external clock synchronization input is grounded for low-ripple Burst Mode operation at low loads, and tying it to a clock source synchronizes the part with pulse-skipping at low loads, where quiescent current rises to 1.5mA. |
| 11 | GND | power_in | Ground exposed pad that must be soldered to the PCB. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10-EP |
| Category | Power Supply Chip |
| Pins | 11 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | | 4 | | 4.3 | V | Note 4 | 3 |
| Quiescent Current from VIN | IQ | | 0.7 | 1.2 | μA | VEN Low | 3 |
| Quiescent Current from VIN | IQ | | 1.7 | 2.7 | μA | VEN High, VSYNC Low | 3 |
| Quiescent Current from VIN | IQ | | | 4.5 | μA | VEN High, VSYNC Low, l (over operating temperature range) | 3 |
| FB Pin Current | IFB | 0.1 | | 12 | nA | VFB = 1.19V, l | 3 |
| Feedback Voltage | VFB | 1.175 | 1.19 | 1.205 | V | l (over operating temperature range), first printed row | 3 |
| Feedback Voltage | VFB | 1.165 | 1.19 | 1.215 | V | l (over operating temperature range), second printed row, grade not labelled | 3 |
| FB Voltage Line Regulation | | | 0.0002 | 0.01 | %/V | 4.3V < VIN < 38V (Note 4) | 3 |
| Switching Frequency | fSW | 1.6 | 2 | 2.4 | MHz | RT = 11k | 3 |
| Switching Frequency | fSW | 0.8 | 1 | 1.2 | MHz | RT = 35.7k | 3 |
| Switching Frequency | fSW | 160 | 200 | 240 | kHz | RT = 255k | 3 |
| Minimum Switch On Time | tON(MIN) | | 80 | | ns | | 3 |
| Minimum Switch Off Time | tOFF(MIN) | | 110 | 150 | ns | | 3 |
| Switch Current Limit | ILIM | 1.8 | 2.4 | 3 | A | | 3 |
| Switch VCESAT | VCESAT | | 330 | | mV | ISW = 1A | 3 |
| Switch Leakage Current | | | 0.02 | 1 | μA | | 3 |
| Boost Schottky Forward Voltage | VF | | 770 | | mV | ISH = 100mA | 3 |
| Boost Schottky Reverse Leakage | IR | | 0.02 | 1 | μA | VREVERSE = 12V | 3 |
| Minimum Boost Voltage | | 1.4 | | 1.8 | V | VIN = 5V, l (Note 3) | 3 |
| BOOST Pin Current | | | 20 | 28 | mA | ISW = 1A, VBOOST = 15V | 3 |
| EN Voltage Threshold | | 0.95 | 1.01 | 1.07 | V | EN Rising, l | 3 |
| EN Voltage Hysteresis | | | 30 | | mV | | 3 |
| EN Pin Current | | | 0.2 | 20 | nA | | 3 |
| LT3971 PG Threshold Offset from VFB | | 60 | 100 | 140 | mV | VFB Rising | 3 |
| LT3971 PG Hysteresis | | | 20 | | mV | | 3 |
| PG Leakage | | | 0.02 | 1 | μA | VPG = 3V | 4 |
| PG Sink Current | | 300 | | 570 | μA | VPG = 0.4V, l | 4 |
| SYNC Threshold | | 0.6 | 0.8 | 1 | V | | 4 |
| SYNC Pin Current | | | 0.1 | | nA | | 4 |
| SS Source Current | ISS | 0.6 | 1 | 1.6 | μA | VSS = 1V | 4 |
| Input Voltage (EN, VIN) | | | | 38 | V | VIN, EN voltage | 2 |
| BOOST Pin Above SW Pin | | | | 30 | V | | 2 |
| FB, VOUT, RT, SYNC, SS Voltage | | | | 6 | V | | 2 |
| PG, BD Voltage | | | | 30 | V | | 2 |
| Boost Diode Current | | | | 1 | A | | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| Operating Junction Temperature Range (LT3971E) | | -40 | | 125 | °C | LT3971E | 2 |
| Thermal Resistance Junction-to-Ambient | θJA | | 45 | | °C/W | MSE 10-lead package | 2 |
| Thermal Resistance Junction-to-Case | θJC | | 10 | | °C/W | MSE 10-lead package | 2 |
## CAD (KiCad official)
- Symbol: `LT3971EMSE#PBF`
- Footprint: `Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm`
- 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files: `lt3971emse-pbf-etched.step` / `lt3971emse-pbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt3971emse-pbf.step` / `lt3971emse-pbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/3971fd.pdf) (28 pp, sha256 `cf769206b11377dd`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt3971emse-pbf-datasheet.pdf)