Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT3970EDDB#TRMPBF

Analog Devices · DC-DC Converters · DFN-10-EP(2x3)

LT3970EDDB#TRMPBF from Analog Devices, in a DFN-10-EP(2x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 FB/VOUT input For the adjustable LT3970 this is FB, regulated to 1.21V from the feedback resistor divider tap (on fixed-output -X versions it is VOUT, connecting to the internal feedback divider for 3.3V, 3.42V or 5V).
2 EN input Shutdown when low and active when high, with hysteretic threshold of 1V rising and 0.97V falling, accurate only when VIN is above 4.2V; tie to VIN if shutdown is not used.
3 VIN power_in Supplies current to the internal circuitry and the internal power switch, and must be locally bypassed.
4 GND power_in Ground pin, must be soldered to the PCB.
5 GND power_in Ground pin, must be soldered to the PCB.
6 SW output Output of the internal power switch, connected to the inductor.
7 BOOST power_in Provides a drive voltage higher than the input voltage to the internal bipolar NPN power switch.
8 BD power_in Anode of the boost diode, which also supplies current to the internal regulator when BD is above 3.2V.
9 PG output Open-drain output of an internal comparator that stays low until FB is within 10% of final regulation voltage, valid when VIN is above 4.2V and EN is high.
10 RT passive A resistor tied between RT and ground sets the switching frequency.
11 GND power_in Exposed pad is ground and must be soldered to the PCB.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package DFN-10-EP(2x3)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Input Voltage 4 4.2 V full operating temperature range 4
Quiescent Current from VIN, VEN Low IQ 0.7 µA VEN Low 4
Quiescent Current from VIN, VEN High IQ 1.7 3.5 µA VEN High, -40°C to 125°C 4
LT3970 Feedback Voltage VFB 1.195 1.21 1.225 V 4
LT3970 Feedback Voltage, -40°C to 125°C VFB 1.185 1.21 1.235 V -40°C to 125°C 4
LT3970 FB Pin Bias Current 0.1 20 nA VFB = 1.21V 4
FB/Output Voltage Line Regulation 0.0002 0.01 %/V 4.2V < VIN < 40V 4
Switching Frequency fSW 1.76 2.25 2.64 MHz RT = 41.2k, VIN = 6V 4
Switching Frequency fSW 640 800 960 kHz RT = 158k, VIN = 6V 4
Switching Frequency fSW 160 200 240 kHz RT = 768k, VIN = 6V 4
Switch Current Limit 535 700 865 mA VIN = 5V, VFB = 0V 4
Catch Schottky Current Limit 350 400 500 mA VIN = 5V 4
Switch Leakage Current 0.05 2 µA 4
Catch Schottky Reverse Leakage 0.05 2 µA VSW = 12V 4
Boost Schottky Reverse Leakage 0.02 2 µA VREVERSE = 12V 4
Minimum Boost Voltage 1.4 1.8 V VIN = 5V 4
BOOST Pin Current 7 10 mA ISW = 200mA, VBOOST = 15V 4
EN Pin Current 1 30 nA VEN = 12V 4
LT3970 EN Voltage Threshold 0.94 1 1.06 V EN Rising, VIN ≥ 4.2V 4
LT3970 PG Threshold Offset from Feedback Voltage 80 120 160 mV VFB Rising 4
PG Leakage 0.01 1 µA VPG = 3V 4
PG Sink Current 30 80 µA VPG = 0.4V 4
Minimum Switch Off-Time 100 160 ns VIN = 10V 4
Switch VCESAT 175 mV ISW = 200mA 4
Catch Schottky Forward Voltage 650 mV ISCH = 100mA, VIN = VBD = NC 4
Boost Schottky Forward Voltage 875 mV ISCH = 50mA, VIN = NC, VBOOST = 0V 4
EN Voltage Hysteresis 30 mV 4
LT3970 PG Hysteresis 12 mV 4
Minimum Switch On-Time 90 ns 4
VIN, EN Voltage 40 V 2
FB/VOUT, RT Voltage 6 V 2
Operating Junction Temperature Range -40 125 °C E-grade 2
Storage Temperature Range -65 150 °C 2
Thermal Resistance Junction to Ambient θJA 76 °C/W DDB package 2

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper resistance further. In the MSOP package, the copper lead 18

CAD (KiCad official)

  • Symbol: LT3970EDDB#TRMPBF
  • Footprint: Package_DFN_QFN:DFN-10-1EP_2x3mm_P0.5mm_EP0.64x2.4mm
  • 3D model: DFN-10-EP(2x3) (KiCad packages3D, STEP)
  • 3D model files: lt3970eddb-trmpbf-etched.step / lt3970eddb-trmpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3970eddb-trmpbf.step / lt3970eddb-trmpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (24 pp, sha256 e25978555387c0ba, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF