3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT3960JMSE#TRPBF
Analog Devices · CAN Transceivers · MSOP-10-EP
LT3960JMSE#TRPBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CANSDAL | bidirectional | Low-level CAN bus line of the I2CAN link that carries the I2C data bus. |
| 2 | CANSDAH | bidirectional | High-level CAN bus line of the I2CAN link that carries the I2C data bus. |
| 3 | GND | power_in | Ground; the datasheet says to solder this pin and the exposed pad directly to the ground plane. |
| 4 | CANSCLH | bidirectional | High-level CAN bus line of the I2CAN link that carries the I2C clock bus. |
| 5 | CANSCLL | bidirectional | Low-level CAN bus line of the I2CAN link that carries the I2C clock bus. |
| 6 | VIN | power_in | Input supply to the internal LDO, specified for 4V to 60V operation, to be bypassed with a 1µF capacitor to GND as close to the pin as possible; tie VIN to VCC if the LDO is unused. |
| 7 | EN/MODE | input | Mode and shutdown pin: tie above 2.5V to select master mode, float to select slave mode, or pull to ground for low-power shutdown. |
| 8 | VCC | power_out | Output of the 3.3V LDO and power supply input for the device, to be bypassed with a 2.2µF or greater capacitor to ground placed as close to the pin as possible. |
| 9 | SCL | bidirectional | I2C serial clock: an input for the master clock when EN/MODE is 2.5V or above, and an output carrying data received on CANSCLH/L when EN/MODE is floating. |
| 10 | SDA | bidirectional | I2C serial data input and output pin. |
| 11 | GND | power_in | Exposed pad is ground and must be soldered to the PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10-EP |
| Category | Communication Interface Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Input Voltage Operating Range (VCC regulated internally from VIN) | VIN | 4 | 60 | V | VCC Regulated Internally from VIN | 3 | |
| VIN Input Voltage Operating Range (VIN tied to VCC, 3.3V range) | VIN | 3 | 3.6 | V | VIN Tied to VCC, 3.3V Range | 3 | |
| VIN Input Voltage Operating Range (VIN tied to VCC, 5V range) | VIN | 4.5 | 5.5 | V | VIN Tied to VCC, 5V Range | 3 | |
| VIN Shutdown Current | IIN(SD) | 20 | 26 | µA | EN/MODE = 0V | 3 | |
| VCC LDO Regulation Voltage | VCC | 3.1 | 3.3 | 3.5 | V | 4V ≤ VIN ≤ 60V, ILDO = 1mA | 3 |
| VCC LDO Current Limit | ILIMCC | 100 | 130 | 160 | mA | VCC = 3.0 | 3 |
| VCC Undervoltage Lockout Threshold (VCC falling) | VUVLO | 2.6 | 2.7 | 2.9 | V | VCC Falling | 3 |
| EN/MODE Shutdown Threshold (falling) | VSHDN | 400 | 700 | 800 | mV | Falling | 3 |
| EN/MODE Master Threshold | VMSTR | 1.9 | 2 | 2.2 | V | 3 | |
| Bus Output Voltage (Dominant) CANxH | VO(D) | 2.15 | 2.9 | 3.3 | V | CANxH t < tTO:CAN, VCC = 3.3V | 3 |
| Bus Output Voltage (Dominant) CANxH | VO(D) | 2.75 | 3.6 | 4.5 | V | CANxH t < tTO:CAN, VCC = 5V | 3 |
| Bus Output Voltage (Dominant) CANxL | VO(D) | 0.5 | 0.9 | 1.65 | V | CANxL t < tTO:CAN, VCC = 3.3V | 3 |
| Bus Output Voltage (Dominant) CANxL | VO(D) | 0.5 | 1.4 | 2.25 | V | CANxL t < tTO:CAN, VCC = 5V | 3 |
| Bus Output Voltage (Recessive) | VO(R) | 1.45 | 1.95 | 2.45 | V | VCC = 3.3V, No Load (Figure 1) | 3 |
| Bus Output Voltage (Recessive) | VO(R) | 2 | 2.5 | 3 | V | VCC = 5V, No Load (Figure 1) | 3 |
| Differential Output Voltage (Dominant) | VOD(D) | 1.5 | 2.2 | 3 | V | RL = 50Ω to 65Ω, VCC = 3.3V | 3 |
| Differential Output Voltage (Dominant) | VOD(D) | 2.7 | 3.1 | 3.5 | V | VCC = 5V | 3 |
| Differential Output Voltage (Recessive) | VOD(R) | -500 | 0 | 50 | mV | No Load (Figure 1) | 3 |
| Common Mode Output Voltage (Dominant) | VOC(R) | 1.45 | 1.95 | 2.45 | V | VCC = 3.3V, (Figure 1) | 3 |
| Common Mode Output Voltage (Dominant) | VOC(R) | 2 | 2.5 | 3 | V | VCC = 5V, (Figure 1) | 3 |
| Bus Output Short-Circuit Current (Dominant) CANxH | IOS(D) | -150 | -75 | -40 | mA | CANxH = 0V | 3 |
| Bus Output Short-Circuit Current (Dominant) CANxH | IOS(D) | -150 | 3 | mA | -40V < CANxH < VO(R) | 3 | |
| Bus Output Short-Circuit Current (Dominant) CANxL | IOS(D) | 25 | 75 | 100 | mA | CANxL = 5V | 3 |
| Bus Output Short-Circuit Current (Dominant) CANxL | IOS(D) | -3 | 100 | mA | VCC < CANxL < 40V | 3 | |
| Bus Common Mode Voltage for Data Reception | VCM | -25 | 25 | V | VCC = 3.3V | 4 | |
| Bus Common Mode Voltage for Data Reception | VCM | -36 | 36 | V | VCC = 5V | 4 | |
| Bus Input Differential Threshold Voltage (Positive Going) | VTH+ | 775 | 900 | mV | VCC = 3.3V, -25V ≤ VCM ≤ 25V | 4 | |
| Bus Input Differential Threshold Voltage (Negative Going) | VTH- | 500 | 625 | mV | VCC = 3.3V, -25V ≤ VCM ≤ 25V | 4 | |
| Input Resistance (CANxH and CANxL) | RIN | 25 | 35.7 | 50 | kΩ | SCL = SDA = VCC; RIN = ∆V/∆I; ∆I = ±20 µA | 4 |
| Differential Input Resistance | RID | 50 | 71.4 | 100 | kΩ | SCL = SDA = VCC; RIN = ∆V/∆I; ∆I = ±20 µA | 4 |
| Bus Leakage Current (Power Off) | IL | -10 | 10 | µA | VCC = 0V, CANxH = CANxL = 5V | 4 | |
| SDA, SCL Input Low Voltage | VIL | 0.4 | V | 4 | |||
| SDA, SCL Input High Voltage | VIH | 1.5 | V | 4 | |||
| SDA, SCL Output Low Voltage | VOL1 | 0.4 | V | ISDA = 3mA | 4 | ||
| Clock/Data Rise Time | tr | 300 | ns | CB = Capacitance of One Bus Line (pF) (Note 5) | 4 | ||
| Clock/Data Fall Time | tf | 300 | ns | CB = Capacitance of One Bus Line (pF) (Note 5) | 4 | ||
| SCL Clock Frequency | fSCL | 0 | 400 | kHz | Notes 5,6 | 5 | |
| I2C to I2CAN Dominant Propagation Delay | tPI2CBD | 45 | 80 | 130 | ns | VCC = 3.3V, Figure 2, Figure 3 | 5 |
| I2C to I2CAN Dominant Propagation Delay | tPI2CBD | 45 | 75 | 115 | ns | VCC = 5V, Figure 2, Figure 3 | 5 |
| I2C to I2CAN Recessive Propagation Delay | tPI2CBR | 80 | 120 | 170 | ns | VCC = 3.3V, Figure 2, Figure 3 | 5 |
| I2C to I2CAN Recessive Propagation Delay | tPI2CBR | 60 | 90 | 120 | ns | VCC = 5V, Figure 2, Figure 3 | 5 |
| I2CAN Dominant to I2C Propagation Delay | tPBI2CD | 25 | 40 | 65 | ns | VCC = 3.3V, Figure 2, Figure 3 | 5 |
| I2CAN Recessive to I2C Propagation Delay | tPBI2CR | 25 | 45 | 80 | ns | VCC = 3.3V, Figure 2, Figure 3 | 5 |
| I2CAN Recessive to I2C Propagation Delay | tPBI2CR | 20 | 35 | 60 | ns | VCC = 5V, Figure 2, Figure 3 | 5 |
| I2CAN Dominant Timeout Time | tTO;CAN | 0.5 | 1.5 | 2 | ms | Figure 2, Figure 4 | 5 |
| I2C Driver Enable from Shutdown | tEN;I2C | 40 | µs | VCC = 3.3V or 5V, Figure 2, Figure 5 | 5 | ||
| I2CAN Driver Enable from Shutdown | tEN;CAN | 40 | µs | VCC = 3.3V or 5V, Figure 2, Figure 6 | 5 | ||
| Time to Shutdown, I2C | tSHDN;I2C | 500 | ns | Figure 2, Figure 5 | 5 | ||
| Time to Shutdown, I2CAN | tSHDN;CAN | 500 | ns | Figure 2, Figure 6 | 5 | ||
| VIN Supply Voltage (absolute maximum) | VIN | 60 | V | 2 | |||
| VCC, EN/MODE Supply Voltage (absolute maximum) | VCC, EN/MODE | 5.5 | V | 2 | |||
| SDA, SCL Voltage (absolute maximum) | SDA, SCL | -0.3 | V | Printed as -0.3V to VCC + 0.3V | 2 | ||
| CANSDAH, CANSDAL, CANSCLH, CANSCLL Voltage (absolute maximum) | -40 | 40 | V | 2 | |||
| Operating Junction Temperature Range (LT3960J) | TJ | -40 | 150 | °C | LT3960J | 2 | |
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Thermal Resistance, Junction-to-Ambient | θJA | 40 | °C/W | 2 |
CAD (KiCad official)
- Symbol:
LT3960JMSE#TRPBF - Footprint:
Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm - 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files:
lt3960jmse-trpbf-etched.step/lt3960jmse-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3960jmse-trpbf.step/lt3960jmse-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (22 pp, sha256
78ac2e8eb476d515, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).