main
Ray Publish 0.1.0 c91ccf1
{
  "slug": "lt3761imse-trpbf",
  "version": "0.1.0",
  "type": "component",
  "description": "Analog Devices LED Drivers, MSOP-16-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",
  "tags": [
    "component",
    "display modules - led drivers - display drivers",
    "lt3761imse#trpbf",
    "factory-2.0.0",
    "extractor-text"
  ],
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "lt3761imse-trpbf.kicad_sym",
    "lt3761imse-trpbf.kicad_mod",
    "lt3761imse-trpbf.glb",
    "lt3761imse-trpbf.step",
    "lt3761imse-trpbf.lbr",
    "docs/hero.png",
    "docs/lt3761imse-trpbf-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html",
    "lt3761imse-trpbf-hero.glb",
    "lt3761imse-trpbf-hero.overlay.json",
    "lt3761imse-trpbf-etched.glb"
  ],
  "component": {
    "mpn": "LT3761IMSE#TRPBF",
    "manufacturer": "Analog Devices",
    "package": "MSOP-16-EP",
    "pin_count": 17,
    "category": "Display Modules / LED Drivers / Display Drivers",
    "subcategory": "LED Drivers",
    "datasheet": "https://www.analog.com/media/en/technical-documentation/data-sheets/37611fb.pdf",
    "parts": {
      "symbol": "lt3761imse-trpbf.kicad_sym",
      "footprint": "lt3761imse-trpbf.kicad_mod",
      "model_3d": "lt3761imse-trpbf-hero.glb",
      "model_3d_plain": "lt3761imse-trpbf-etched.glb",
      "model_3d_step": "lt3761imse-trpbf-etched.step",
      "model_3d_step_plain": "lt3761imse-trpbf.step",
      "lbr": "lt3761imse-trpbf.lbr"
    },
    "distributor_links": {
      "lcsc": "C671521",
      "digikey": "LT3761IMSE#TRPBFTR-ND",
      "mouser": "584-LT3761IMSE#TRPBF"
    },
    "distributor_check": {
      "checked_at": "2026-10-30T22:41:10Z",
      "source": "Component Ocean /api/assign-pns",
      "digikey": {
        "pn": "LT3761IMSE#TRPBFTR-ND",
        "status": "found"
      },
      "mouser": {
        "pn": "584-LT3761IMSE#TRPBF",
        "status": "found"
      }
    },
    "pins": [
      {
        "number": "1",
        "name": "PWMOUT",
        "type": "output",
        "description": "Buffered PWM signal for driving an LED load disconnect NMOS or level shift, driven from INTVCC and toggled when FB exceeds VFB plus 60mV (typical); a FET with gate cut-off above 1V is recommended."
      },
      {
        "number": "2",
        "name": "FB",
        "type": "input",
        "description": "Voltage loop feedback regulated to 1.25V (nominal) for constant-voltage control and open-LED detection, with FB above the overvoltage threshold forcing PWMOUT and GATE low; do not leave open, connect to GND if unused."
      },
      {
        "number": "3",
        "name": "ISN",
        "type": "input",
        "description": "Negative terminal connection of the current feedback resistor, where the LED current is ILED = 250mV/RLED when CTRL > 1.2V and input bias current is typically 20µA into the pin when ISN is above INTVCC."
      },
      {
        "number": "4",
        "name": "ISP",
        "type": "input",
        "description": "Positive terminal connection of the current feedback resistor, where a difference between ISP and ISN exceeding 600mV (typical) triggers an overcurrent event that pulls GATE and PWMOUT low."
      },
      {
        "number": "5",
        "name": "VC",
        "type": "output",
        "description": "Transconductance error amplifier output used to stabilize the control loop with an RC network, connected to a capacitor to GND and high impedance when PWM is low."
      },
      {
        "number": "6",
        "name": "CTRL",
        "type": "input",
        "description": "Current sense threshold adjustment input where VISP-ISN is linear from 0V to 1V and reaches full scale 250mV above 1.2V, and must not be left open."
      },
      {
        "number": "7",
        "name": "VREF",
        "type": "power_in",
        "description": "Voltage reference output, typically 2V, that drives a resistor divider for CTRL and can supply up to 185µA (typical)."
      },
      {
        "number": "8",
        "name": "PWM",
        "type": "input",
        "description": "Digital PWM dimming input where a low turns off the switcher and idles the oscillator, and a capacitor to GND sets a self-oscillating dimming frequency; connect to INTVCC if not used."
      },
      {
        "number": "9",
        "name": "OPENLED",
        "type": "output",
        "description": "Open-drain pull-down asserted when FB is above VFB minus 50mV (typical) and ISP-ISN is below 25mV, requiring an external pull-up usually to INTVCC (LT3761 only; SYNC on LT3761-1)."
      },
      {
        "number": "10",
        "name": "DIM/SS",
        "type": "passive",
        "description": "Soft-start and PWMOUT dimming signal generator programming pin with an internal 12µA (typical) pull-up, requiring a capacitor to GND of at least 560pF when the PWMOUT generator is used."
      },
      {
        "number": "11",
        "name": "RT",
        "type": "passive",
        "description": "Switching frequency adjustment pin set by a resistor to GND, which must not be left open and should be placed close to the IC."
      },
      {
        "number": "12",
        "name": "EN/UVLO",
        "type": "input",
        "description": "Enable and undervoltage detect pin with a 1.22V falling threshold and 1.24V (typical) rising enable threshold, which must be tied to 0.4V or less to disable the device and reduce VIN quiescent current below 1µA."
      },
      {
        "number": "13",
        "name": "INTVCC",
        "type": "power_out",
        "description": "Current-limited low-dropout linear regulator output regulating to 7.85V (typical) from VIN, which must be bypassed with a 1µF ceramic capacitor placed close to the pin and the exposed pad."
      },
      {
        "number": "14",
        "name": "VIN",
        "type": "power_in",
        "description": "Power supply input for internal loads and the INTVCC regulator, which must be locally bypassed with a 0.22µF (or larger) low-ESR capacitor placed close to the pin."
      },
      {
        "number": "15",
        "name": "SENSE",
        "type": "input",
        "description": "Current sense input for the switch control loop that must be Kelvin connected to the positive terminal of the switch current sense resistor in the source of the external NFET."
      },
      {
        "number": "16",
        "name": "GATE",
        "type": "output",
        "description": "N-channel FET gate driver output that switches between INTVCC and GND and is driven to GND during shutdown, fault or idle states."
      },
      {
        "number": "17",
        "name": "GND",
        "type": "power_in",
        "description": "Exposed pad ground that also serves as the control loop current sense return and must be soldered directly to the ground plane."
      }
    ],
    "provenance": {
      "extractor": "extract_pins 0.3",
      "factory_chain": {
        "factory": "2.0.0",
        "extractor": "extract_pins 0.3",
        "primary_model": "claude-haiku-5-5",
        "primary_mode": "text",
        "consensus_model": "claude-sonnet-5-5",
        "consensus": "agreed",
        "guards": "pin_guards 0.1: passed",
        "guard_notes": [
          "extractor flagged: MPN LT3761IMSE#TRPBF is the LT3761 (not -1) variant, so pin 9 is OPENLED. Pin 9 is SYNC on the LT376"
        ],
        "pages_sent": 7,
        "cost_usd": 0.0226,
        "at": "2026-10-30T22:41:01"
      },
      "datasheet": {
        "url": "https://www.analog.com/media/en/technical-documentation/data-sheets/37611fb.pdf",
        "pages": 32,
        "sha256": "733340007eac0a67",
        "source_tier": "mfr"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 17,
        "described": 17,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "lt3761imse-trpbf.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          4.9,
          4.039,
          0.95
        ],
        "zmin_mm": -0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "e807f0e0e2c0c408c18dc198f4fc826ff019157c0529c7e78e68c1aab270d826",
        "checked": "2026-10-30",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "lt3761imse-trpbf-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          4.9,
          4.039,
          0.95
        ],
        "zmin_mm": -0.0,
        "centre_offset_mm": 0.0,
        "footprint_binding": "identity",
        "sha256": "f5ac00f209d4947f1d9191a59bb4357ffd61609f7ac5a983e9e8030afa864aa2",
        "checked": "2026-10-30",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  }
}