main
Ray
Publish 0.1.0
c91ccf1
LT3761IMSE#TRPBF
Analog Devices · LED Drivers · MSOP-16-EP
LT3761IMSE#TRPBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PWMOUT | output | Buffered PWM signal for driving an LED load disconnect NMOS or level shift, driven from INTVCC and toggled when FB exceeds VFB plus 60mV (typical); a FET with gate cut-off above 1V is recommended. |
| 2 | FB | input | Voltage loop feedback regulated to 1.25V (nominal) for constant-voltage control and open-LED detection, with FB above the overvoltage threshold forcing PWMOUT and GATE low; do not leave open, connect to GND if unused. |
| 3 | ISN | input | Negative terminal connection of the current feedback resistor, where the LED current is ILED = 250mV/RLED when CTRL > 1.2V and input bias current is typically 20µA into the pin when ISN is above INTVCC. |
| 4 | ISP | input | Positive terminal connection of the current feedback resistor, where a difference between ISP and ISN exceeding 600mV (typical) triggers an overcurrent event that pulls GATE and PWMOUT low. |
| 5 | VC | output | Transconductance error amplifier output used to stabilize the control loop with an RC network, connected to a capacitor to GND and high impedance when PWM is low. |
| 6 | CTRL | input | Current sense threshold adjustment input where VISP-ISN is linear from 0V to 1V and reaches full scale 250mV above 1.2V, and must not be left open. |
| 7 | VREF | power_in | Voltage reference output, typically 2V, that drives a resistor divider for CTRL and can supply up to 185µA (typical). |
| 8 | PWM | input | Digital PWM dimming input where a low turns off the switcher and idles the oscillator, and a capacitor to GND sets a self-oscillating dimming frequency; connect to INTVCC if not used. |
| 9 | OPENLED | output | Open-drain pull-down asserted when FB is above VFB minus 50mV (typical) and ISP-ISN is below 25mV, requiring an external pull-up usually to INTVCC (LT3761 only; SYNC on LT3761-1). |
| 10 | DIM/SS | passive | Soft-start and PWMOUT dimming signal generator programming pin with an internal 12µA (typical) pull-up, requiring a capacitor to GND of at least 560pF when the PWMOUT generator is used. |
| 11 | RT | passive | Switching frequency adjustment pin set by a resistor to GND, which must not be left open and should be placed close to the IC. |
| 12 | EN/UVLO | input | Enable and undervoltage detect pin with a 1.22V falling threshold and 1.24V (typical) rising enable threshold, which must be tied to 0.4V or less to disable the device and reduce VIN quiescent current below 1µA. |
| 13 | INTVCC | power_out | Current-limited low-dropout linear regulator output regulating to 7.85V (typical) from VIN, which must be bypassed with a 1µF ceramic capacitor placed close to the pin and the exposed pad. |
| 14 | VIN | power_in | Power supply input for internal loads and the INTVCC regulator, which must be locally bypassed with a 0.22µF (or larger) low-ESR capacitor placed close to the pin. |
| 15 | SENSE | input | Current sense input for the switch control loop that must be Kelvin connected to the positive terminal of the switch current sense resistor in the source of the external NFET. |
| 16 | GATE | output | N-channel FET gate driver output that switches between INTVCC and GND and is driven to GND during shutdown, fault or idle states. |
| 17 | GND | power_in | Exposed pad ground that also serves as the control loop current sense return and must be soldered directly to the ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN absolute maximum | VIN | 60 | V | VIN, EN/UVLO pins | 2 | ||
| ISP, ISN absolute maximum | ISP, ISN | 80 | V | 2 | |||
| INTVCC absolute maximum | INTVCC | 9.6 | V | printed as VIN + 0.3V, 9.6V | 2 | ||
| CTRL, OPENLED absolute maximum | CTRL, OPENLED | 15 | V | 2 | |||
| FB, PWM, SYNC absolute maximum | FB, PWM, SYNC | 9.6 | V | 2 | |||
| VC, VREF absolute maximum | VC, VREF | 3 | V | 2 | |||
| RT, DIM/SS absolute maximum | RT, DIM/SS | 1.5 | V | 2 | |||
| SENSE absolute maximum | SENSE | 0.5 | V | 2 | |||
| Storage temperature range | -65 | 150 | °C | 2 | |||
| Operating ambient temperature range | -40 | 125 | °C | LT3761I/LT3761I-1 | 2 | ||
| Maximum junction temperature | TJMAX | 125 | °C | E-, I-GRADES | 2 | ||
| Thermal resistance, junction to ambient | θJA | 43 | °C/W | 2 | |||
| Thermal resistance, junction to case | θJC | 4 | °C/W | 2 | |||
| VIN Minimum Operating Voltage | 4.5 | V | VIN tied to INTVCC | 2 | |||
| VIN Shutdown IQ | IQ | 0.1 | 1 | µA | EN/UVLO = 0V, PWM = 0V | 2 | |
| VIN Shutdown IQ | IQ | 6 | µA | EN/UVLO = 1.15V, PWM = 0V | 2 | ||
| VIN Operating IQ (Not Switching) | IQ | 1.8 | 2.2 | mA | PWM = 0V | 2 | |
| VREF Voltage | VREF | 1.955 | 2.02 | 2.05 | V | -100µA ≤ IVREF ≤ 0µA | 2 |
| VREF Pull-Up Current | 150 | 185 | 210 | µA | VREF = 0V | 2 | |
| SENSE Current Limit Threshold | 98 | 105 | 118 | mV | 2 | ||
| DIM/SS Pull-Up Current | 10 | 12 | 14 | µA | Current out of pin, DIM/SS = 0V | 2 | |
| Full-Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 242 | 250 | 258 | mV | CTRL ≥ 1.2V, ISP = 48V | 3 |
| Full-Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 243 | 257 | 268 | mV | CTRL ≥ 1.2V, ISN = 0V | 3 |
| 1/10th Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 21 | 25 | 30 | mV | CTRL = 0.2V, ISP = 48V | 3 |
| 1/10th Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 17 | 28 | 39 | mV | CTRL = 0.2V, ISN = 0V | 3 |
| Mid-Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 96 | 100 | 104 | mV | CTRL = 0.5V, ISP = 48V | 3 |
| Mid-Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 95 | 105 | 115 | mV | CTRL = 0.5V, ISN = 0V | 3 |
| ISP/ISN Current Sense Amplifier Input Common Mode Range (VISN) | VISN | 0 | 80 | V | 3 | ||
| CTRL Pin Range for Linear Current Sense Threshold Adjustment | CTRL | 0 | 1 | V | 3 | ||
| VC Standby Input Bias Current | -20 | 20 | nA | PWM = 0V | 3 | ||
| FB Regulation Voltage (VFB) | VFB | 1.225 | 1.255 | 1.275 | V | ISP = ISN = 48V, 0V | 3 |
| FB Open LED Threshold | -65 | -50 | -40 | mV | Relative to VFB; OPENLED falling, ISP tied to ISN (LT3761 only) | 3 | |
| C/10 Inhibit for OPENLED Assertion (VISP-ISN) | VISP-ISN | 14 | 25 | 39 | mV | FB = VFB, ISN = 48V, 0V (LT3761 only) | 3 |
| FB Overvoltage Threshold | 50 | 60 | 75 | mV | Relative to VFB; PWMOUT falling | 3 | |
| Switching Frequency | fOSC | 85 | 100 | 115 | kHz | RT = 95.3kΩ | 3 |
| Switching Frequency | fOSC | 925 | 1000 | 1050 | kHz | RT = 8.87kΩ | 3 |
| INTVCC Regulation Voltage | INTVCC | 7.6 | 7.85 | 8.05 | V | 10V ≤ VIN ≤ 60V | 3 |
| INTVCC Maximum Operating Voltage | INTVCC | 8.1 | V | 3 | |||
| INTVCC Minimum Operating Voltage | INTVCC | 4.5 | V | 3 | |||
| INTVCC Undervoltage Lockout | 3.9 | 4.1 | 4.4 | V | EN/UVLO = 2V | 4 | |
| INTVCC Current Limit | 30 | 36 | 42 | mA | INTVCC = 6V, 8V ≤ VIN ≤ 60V | 4 | |
| EN/UVLO Threshold Voltage Falling | 1.18 | 1.22 | 1.26 | V | Falling | 4 | |
| EN/UVLO Pin Bias Current Low | 1.7 | 2.3 | 2.7 | µA | EN/UVLO = 1.15V | 4 | |
| PWM Falling Threshold | 0.78 | 0.83 | 0.88 | V | 4 | ||
| PWM Threshold Hysteresis (VPWMHYS) | VPWMHYS | 0.35 | 0.4 | 0.6 | V | IDIM/SS = 0µA | 4 |
| PWM Pull-Up Current (IPWMUP) | IPWMUP | 6 | 7.5 | 9 | µA | PWM = 0.7V, IDIM/SS = 0µA | 4 |
| PWM Pull-Down Current (IPWMDN) | IPWMDN | 68 | 88 | 110 | µA | PWM = 1.5V, IDIM/SS = 0µA | 4 |
| PWMOUT Duty Ratio for PWM Signal Generator | 3.1 | 4.1 | 5.2 | % | IDIM/SS = -6.5µA | 4 | |
| PWMOUT Duty Ratio for PWM Signal Generator | 6.8 | 7.9 | 9.2 | % | IDIM/SS = 0µA | 4 | |
| PWMOUT Duty Ratio for PWM Signal Generator | 40 | 47.8 | 56 | % | IDIM/SS = 21.5µA | 4 | |
| PWMOUT Duty Ratio for PWM Signal Generator | 95 | 96.5 | 98 | % | IDIM/SS = 52µA | 4 | |
| PWMOUT Signal Generator Frequency | 215 | 300 | 435 | Hz | PWM = 47nF to GND, IDIM/SS = 0µA | 4 |
CAD (KiCad official)
- Symbol:
LT3761IMSE#TRPBF - Footprint:
Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm - 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lt3761imse-trpbf-etched.step/lt3761imse-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3761imse-trpbf.step/lt3761imse-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (32 pp, sha256
733340007eac0a67, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT3761IMSE#TRPBF
**Analog Devices** · LED Drivers · MSOP-16-EP
LT3761IMSE#TRPBF from Analog Devices, in a MSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PWMOUT | output | Buffered PWM signal for driving an LED load disconnect NMOS or level shift, driven from INTVCC and toggled when FB exceeds VFB plus 60mV (typical); a FET with gate cut-off above 1V is recommended. |
| 2 | FB | input | Voltage loop feedback regulated to 1.25V (nominal) for constant-voltage control and open-LED detection, with FB above the overvoltage threshold forcing PWMOUT and GATE low; do not leave open, connect to GND if unused. |
| 3 | ISN | input | Negative terminal connection of the current feedback resistor, where the LED current is ILED = 250mV/RLED when CTRL > 1.2V and input bias current is typically 20µA into the pin when ISN is above INTVCC. |
| 4 | ISP | input | Positive terminal connection of the current feedback resistor, where a difference between ISP and ISN exceeding 600mV (typical) triggers an overcurrent event that pulls GATE and PWMOUT low. |
| 5 | VC | output | Transconductance error amplifier output used to stabilize the control loop with an RC network, connected to a capacitor to GND and high impedance when PWM is low. |
| 6 | CTRL | input | Current sense threshold adjustment input where VISP-ISN is linear from 0V to 1V and reaches full scale 250mV above 1.2V, and must not be left open. |
| 7 | VREF | power_in | Voltage reference output, typically 2V, that drives a resistor divider for CTRL and can supply up to 185µA (typical). |
| 8 | PWM | input | Digital PWM dimming input where a low turns off the switcher and idles the oscillator, and a capacitor to GND sets a self-oscillating dimming frequency; connect to INTVCC if not used. |
| 9 | OPENLED | output | Open-drain pull-down asserted when FB is above VFB minus 50mV (typical) and ISP-ISN is below 25mV, requiring an external pull-up usually to INTVCC (LT3761 only; SYNC on LT3761-1). |
| 10 | DIM/SS | passive | Soft-start and PWMOUT dimming signal generator programming pin with an internal 12µA (typical) pull-up, requiring a capacitor to GND of at least 560pF when the PWMOUT generator is used. |
| 11 | RT | passive | Switching frequency adjustment pin set by a resistor to GND, which must not be left open and should be placed close to the IC. |
| 12 | EN/UVLO | input | Enable and undervoltage detect pin with a 1.22V falling threshold and 1.24V (typical) rising enable threshold, which must be tied to 0.4V or less to disable the device and reduce VIN quiescent current below 1µA. |
| 13 | INTVCC | power_out | Current-limited low-dropout linear regulator output regulating to 7.85V (typical) from VIN, which must be bypassed with a 1µF ceramic capacitor placed close to the pin and the exposed pad. |
| 14 | VIN | power_in | Power supply input for internal loads and the INTVCC regulator, which must be locally bypassed with a 0.22µF (or larger) low-ESR capacitor placed close to the pin. |
| 15 | SENSE | input | Current sense input for the switch control loop that must be Kelvin connected to the positive terminal of the switch current sense resistor in the source of the external NFET. |
| 16 | GATE | output | N-channel FET gate driver output that switches between INTVCC and GND and is driven to GND during shutdown, fault or idle states. |
| 17 | GND | power_in | Exposed pad ground that also serves as the control loop current sense return and must be soldered directly to the ground plane. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16-EP |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN absolute maximum | VIN | | | 60 | V | VIN, EN/UVLO pins | 2 |
| ISP, ISN absolute maximum | ISP, ISN | | | 80 | V | | 2 |
| INTVCC absolute maximum | INTVCC | | | 9.6 | V | printed as VIN + 0.3V, 9.6V | 2 |
| CTRL, OPENLED absolute maximum | CTRL, OPENLED | | | 15 | V | | 2 |
| FB, PWM, SYNC absolute maximum | FB, PWM, SYNC | | | 9.6 | V | | 2 |
| VC, VREF absolute maximum | VC, VREF | | | 3 | V | | 2 |
| RT, DIM/SS absolute maximum | RT, DIM/SS | | | 1.5 | V | | 2 |
| SENSE absolute maximum | SENSE | | | 0.5 | V | | 2 |
| Storage temperature range | | -65 | | 150 | °C | | 2 |
| Operating ambient temperature range | | -40 | | 125 | °C | LT3761I/LT3761I-1 | 2 |
| Maximum junction temperature | TJMAX | | | 125 | °C | E-, I-GRADES | 2 |
| Thermal resistance, junction to ambient | θJA | | 43 | | °C/W | | 2 |
| Thermal resistance, junction to case | θJC | | 4 | | °C/W | | 2 |
| VIN Minimum Operating Voltage | | 4.5 | | | V | VIN tied to INTVCC | 2 |
| VIN Shutdown IQ | IQ | | 0.1 | 1 | µA | EN/UVLO = 0V, PWM = 0V | 2 |
| VIN Shutdown IQ | IQ | | | 6 | µA | EN/UVLO = 1.15V, PWM = 0V | 2 |
| VIN Operating IQ (Not Switching) | IQ | | 1.8 | 2.2 | mA | PWM = 0V | 2 |
| VREF Voltage | VREF | 1.955 | 2.02 | 2.05 | V | -100µA ≤ IVREF ≤ 0µA | 2 |
| VREF Pull-Up Current | | 150 | 185 | 210 | µA | VREF = 0V | 2 |
| SENSE Current Limit Threshold | | 98 | 105 | 118 | mV | | 2 |
| DIM/SS Pull-Up Current | | 10 | 12 | 14 | µA | Current out of pin, DIM/SS = 0V | 2 |
| Full-Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 242 | 250 | 258 | mV | CTRL ≥ 1.2V, ISP = 48V | 3 |
| Full-Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 243 | 257 | 268 | mV | CTRL ≥ 1.2V, ISN = 0V | 3 |
| 1/10th Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 21 | 25 | 30 | mV | CTRL = 0.2V, ISP = 48V | 3 |
| 1/10th Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 17 | 28 | 39 | mV | CTRL = 0.2V, ISN = 0V | 3 |
| Mid-Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 96 | 100 | 104 | mV | CTRL = 0.5V, ISP = 48V | 3 |
| Mid-Scale ISP/ISN Current Sense Threshold (VISP-ISN) | VISP-ISN | 95 | 105 | 115 | mV | CTRL = 0.5V, ISN = 0V | 3 |
| ISP/ISN Current Sense Amplifier Input Common Mode Range (VISN) | VISN | 0 | | 80 | V | | 3 |
| CTRL Pin Range for Linear Current Sense Threshold Adjustment | CTRL | 0 | | 1 | V | | 3 |
| VC Standby Input Bias Current | | -20 | | 20 | nA | PWM = 0V | 3 |
| FB Regulation Voltage (VFB) | VFB | 1.225 | 1.255 | 1.275 | V | ISP = ISN = 48V, 0V | 3 |
| FB Open LED Threshold | | -65 | -50 | -40 | mV | Relative to VFB; OPENLED falling, ISP tied to ISN (LT3761 only) | 3 |
| C/10 Inhibit for OPENLED Assertion (VISP-ISN) | VISP-ISN | 14 | 25 | 39 | mV | FB = VFB, ISN = 48V, 0V (LT3761 only) | 3 |
| FB Overvoltage Threshold | | 50 | 60 | 75 | mV | Relative to VFB; PWMOUT falling | 3 |
| Switching Frequency | fOSC | 85 | 100 | 115 | kHz | RT = 95.3kΩ | 3 |
| Switching Frequency | fOSC | 925 | 1000 | 1050 | kHz | RT = 8.87kΩ | 3 |
| INTVCC Regulation Voltage | INTVCC | 7.6 | 7.85 | 8.05 | V | 10V ≤ VIN ≤ 60V | 3 |
| INTVCC Maximum Operating Voltage | INTVCC | | | 8.1 | V | | 3 |
| INTVCC Minimum Operating Voltage | INTVCC | 4.5 | | | V | | 3 |
| INTVCC Undervoltage Lockout | | 3.9 | 4.1 | 4.4 | V | EN/UVLO = 2V | 4 |
| INTVCC Current Limit | | 30 | 36 | 42 | mA | INTVCC = 6V, 8V ≤ VIN ≤ 60V | 4 |
| EN/UVLO Threshold Voltage Falling | | 1.18 | 1.22 | 1.26 | V | Falling | 4 |
| EN/UVLO Pin Bias Current Low | | 1.7 | 2.3 | 2.7 | µA | EN/UVLO = 1.15V | 4 |
| PWM Falling Threshold | | 0.78 | 0.83 | 0.88 | V | | 4 |
| PWM Threshold Hysteresis (VPWMHYS) | VPWMHYS | 0.35 | 0.4 | 0.6 | V | IDIM/SS = 0µA | 4 |
| PWM Pull-Up Current (IPWMUP) | IPWMUP | 6 | 7.5 | 9 | µA | PWM = 0.7V, IDIM/SS = 0µA | 4 |
| PWM Pull-Down Current (IPWMDN) | IPWMDN | 68 | 88 | 110 | µA | PWM = 1.5V, IDIM/SS = 0µA | 4 |
| PWMOUT Duty Ratio for PWM Signal Generator | | 3.1 | 4.1 | 5.2 | % | IDIM/SS = -6.5µA | 4 |
| PWMOUT Duty Ratio for PWM Signal Generator | | 6.8 | 7.9 | 9.2 | % | IDIM/SS = 0µA | 4 |
| PWMOUT Duty Ratio for PWM Signal Generator | | 40 | 47.8 | 56 | % | IDIM/SS = 21.5µA | 4 |
| PWMOUT Duty Ratio for PWM Signal Generator | | 95 | 96.5 | 98 | % | IDIM/SS = 52µA | 4 |
| PWMOUT Signal Generator Frequency | | 215 | 300 | 435 | Hz | PWM = 47nF to GND, IDIM/SS = 0µA | 4 |
## CAD (KiCad official)
- Symbol: `LT3761IMSE#TRPBF`
- Footprint: `Package_SO:MSOP-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm`
- 3D model: MSOP-16-EP (KiCad packages3D, STEP)
- 3D model files: `lt3761imse-trpbf-etched.step` / `lt3761imse-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt3761imse-trpbf.step` / `lt3761imse-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/37611fb.pdf) (32 pp, sha256 `733340007eac0a67`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt3761imse-trpbf-datasheet.pdf)