3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT3758AEMSE#TRPBF
Analog Devices · DC-DC Controllers · MSOP-10-EP
LT3758AEMSE#TRPBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VC | passive | Error amplifier compensation pin used to stabilize the voltage loop with an external RC network. |
| 2 | FBX | input | Positive and negative feedback pin that receives the divider voltage from the output, regulating to 1.6V (FBX > 0V) or -0.8V (FBX < 0V), and modulates switching frequency during start-up and faults when FBX is close to GND. |
| 3 | SS | passive | Soft-start pin whose external capacitor sets the soft-start interval, with a 10µA (typical) pull-up to an internal 2.5V rail, reset to GND by undervoltage at SHDN/UVLO, INTVCC undervoltage or overvoltage, or internal thermal lockout. |
| 4 | RT | passive | Switching frequency adjustment pin set by a resistor to GND, which must not be left open; the datasheet specifies 100kHz to 1MHz operation. |
| 5 | SYNC | input | Frequency synchronization pin; the RT resistor should program a switching frequency 20% slower than the SYNC pulse frequency, and it must be tied to GND if the feature is not used. |
| 6 | SENSE | input | Current sense input for the control loop that must be Kelvin connected to the positive terminal of the switch current sense resistor, with its negative terminal connected to the GND plane close to the IC. |
| 7 | GATE | output | N-channel MOSFET gate driver output that switches between INTVCC and GND and is driven to GND when the IC is shut down, in thermal lockout, or when INTVCC is outside its over- or undervoltage thresholds. |
| 8 | INTVCC | power_out | Regulated supply for internal loads and the gate driver, regulated to 7.2V (typical) and requiring a minimum 4.7µF bypass capacitor close to the pin; it may be tied directly to VIN only if VIN is below 17.5V. |
| 9 | SHDN/UVLO | input | Shutdown and undervoltage detect pin with an accurate 1.22V (nominal) falling threshold, where tying it to 0.4V or less disables the device and reduces VIN quiescent current below 1µA. |
| 10 | VIN | power_in | Input supply pin that must be locally bypassed with a 0.22µF or larger capacitor placed close to the pin, with the part operating from a 5.5V to 100V input range. |
| 11 | GND | power_in | Exposed pad ground that also serves as the negative terminal of the current sense resistor and must be soldered directly to the local ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10-EP |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Operating Range | VIN | 5.5 | 100 | V | 3 | ||
| VIN Shutdown IQ | IQ | 0.1 | 1 | µA | SHDN/UVLO = 0V | 3 | |
| VIN Shutdown IQ | IQ | 6 | µA | SHDN/UVLO = 1.15V | 3 | ||
| VIN Operating IQ | IQ | 1.75 | 2.2 | mA | VC = 0.3V, RT = 41.2k | 3 | |
| VIN Operating IQ with Internal LDO Disabled | IQ | 350 | 400 | µA | VC = 0.3V, RT = 41.2k, INTVCC = 7.5V | 3 | |
| SENSE Current Limit Threshold | VSENSE(MAX) | 100 | 110 | 120 | mV | l (full operating temperature range) | 3 |
| FBX Regulation Voltage (positive) | VFBX(REG) | 1.569 | 1.6 | 1.631 | V | FBX > 0V (Note 3); l | 3 |
| FBX Regulation Voltage (negative) | VFBX(REG) | -0.816 | -0.8 | -0.784 | V | FBX < 0V (Note 3); l | 3 |
| FBX Overvoltage Lockout | 6 | 8 | 10 | % | FBX > 0V (Note 4) | 3 | |
| FBX Overvoltage Lockout | 7 | 11 | 14 | % | FBX < 0V (Note 4) | 3 | |
| FBX Pin Input Current | -10 | 10 | nA | FBX = 1.6V (Note 3) | 3 | ||
| FBX Pin Input Current | 70 | 100 | nA | FBX = -0.8V (Note 3) | 3 | ||
| VFBX Line Regulation (positive) | ∆VFBX/[∆VIN • VFBX(REG)] | 0.006 | 0.025 | %/V | FBX > 0V, 5.5V < VIN < 100V (Notes 3, 6) | 3 | |
| VFBX Line Regulation (negative) | ∆VFBX/[∆VIN • VFBX(REG)] | 0.005 | 0.03 | %/V | FBX < 0V, 5.5V < VIN < 100V (Notes 3, 6) | 3 | |
| Switching Frequency | fSW | 270 | 300 | 330 | kHz | RT = 41.2k to GND, FBX = 1.6V | 3 |
| SYNC Input Low | 0.4 | V | 3 | ||||
| SYNC Input High | 1.5 | V | 3 | ||||
| INTVCC Regulation Voltage | INTVCC | 7 | 7.2 | 7.4 | V | l (full operating temperature range) | 4 |
| INTVCC Undervoltage Lockout Threshold | 4.3 | 4.5 | 4.7 | V | Falling INTVCC | 4 | |
| INTVCC Current Limit | 11 | 16 | 22 | mA | VIN = 100V | 4 | |
| INTVCC Load Regulation | (∆VINTVCC /VINTVCC) | -1 | -0.4 | % | 0 < IINTVCC < 10mA, VIN = 8V | 4 | |
| INTVCC Line Regulation | (∆VINTVCC /[∆VIN • VINTVCC]) | 0.005 | 0.02 | %/V | 8V < VIN < 100V | 4 | |
| Dropout Voltage (VIN, VINTVCC) | 500 | mV | VIN = 6V, IINTVCC = 10mA | 4 | |||
| INTVCC Voltage to Bypass Internal LDO | 7.5 | V | 4 | ||||
| SHDN/UVLO Threshold Voltage Falling | 1.17 | 1.22 | 1.27 | V | VIN = INTVCC = 8V; l (full operating temperature range) | 4 | |
| SHDN/UVLO Input Low Voltage | 0.4 | V | IVIN drops below 1µA | 4 | |||
| SHDN/UVLO Pin Bias Current Low | 1.7 | 2 | 2.5 | µA | SHDN/UVLO = 1.15V | 4 | |
| SHDN/UVLO Pin Bias Current High | 10 | 100 | nA | SHDN/UVLO = 1.33V | 4 | ||
| Gate Output Low (VOL) | VOL | 0.05 | V | 4 | |||
| Operating Junction Temperature Range (E grade) | TJ | -40 | 125 | °C | LT3758E/LT3758AE | 2 | |
| VIN, SHDN/UVLO (absolute maximum) | VIN | 100 | V | Note 7 | 2 | ||
| INTVCC (absolute maximum) | INTVCC | 20 | V | 2 | |||
| SYNC (absolute maximum) | SYNC | 8 | V | 2 | |||
| VC, SS (absolute maximum) | VC, SS | 3 | V | 2 | |||
| RT (absolute maximum) | RT | 1.5 | V | 2 | |||
| SENSE (absolute maximum) | SENSE | -0.3 | 0.3 | V | 2 | ||
| FBX (absolute maximum) | FBX | -6 | 6 | V | 2 | ||
| Storage Temperature Range (MSOP) | TSTG | -65 | 150 | °C | MSOP package | 2 | |
| Lead Temperature (Soldering) | 300 | °C | 10 sec, MSOP | 2 | |||
| Maximum Junction Temperature (MSE package) | TJMAX | 150 | °C | MSE package | 2 | ||
| Junction-to-Ambient Thermal Resistance (MSE package) | θJA | 40 | °C/W | MSE package, exposed pad soldered to full copper plane | 2 |
CAD (KiCad official)
- Symbol:
LT3758AEMSE#TRPBF - Footprint:
Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm - 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files:
lt3758aemse-trpbf-etched.step/lt3758aemse-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3758aemse-trpbf.step/lt3758aemse-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (38 pp, sha256
5c10ae6fde7c3a83, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).