main
Ray
Publish 0.1.0
52e7ba4
LT3502IDC#TRMPBF
Analog Devices · DC-DC Converters · DFN-8-EP(2x2)
LT3502IDC#TRMPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Supplies current to the internal regulator and internal power switch, must be locally bypassed; input range 3V to 40V (absolute max 40V). |
| 2 | BD | power_in | Provides current to the internal boost Schottky diode; absolute maximum voltage 7V. |
| 3 | FB | input | Feedback pin regulated to 0.8V; connect the feedback resistor divider tap here, VOUT = 0.8(1 + R1/R2) with R2 of about 10k. |
| 4 | SHDN | input | Shutdown pin: tie to ground to shut down, tie to 2V or more for normal operation, tie to VIN if unused, also provides soft-start and frequency foldback, and must not exceed VIN. |
| 5 | GND | power_in | Ground pin. |
| 6 | DA | input | Connect the catch diode (D1) anode to this pin; used to provide frequency foldback in extreme situations. |
| 7 | BOOST | power_in | Provides a drive voltage higher than the input voltage to the internal NPN power switch; connect a boost capacitor from this pin to SW; absolute max 50V. |
| 8 | SW | output | Output of the internal power switch; connect to the inductor, catch diode and boost capacitor. |
| 9 | EP | power_in | Exposed pad (pin 9) is GND and must be soldered to the PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-8-EP(2x2) |
| Category | Power Supply Chip |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Undervoltage Lockout | 2.6 | 2.8 | 3 | V | 3 | ||
| Quiescent Current at Shutdown | 0.5 | 2 | µA | VSHDN = 0V | 3 | ||
| Quiescent Current Not Switching | 1.5 | 2 | mA | 3 | |||
| Feedback Voltage (2mm × 2mm DFN) | 0.79 | 0.8 | 0.81 | V | 2mm × 2mm DFN, TA = 25°C | 3 | |
| Feedback Voltage (2mm × 2mm DFN, full range) | 0.785 | 0.8 | 0.813 | V | 2mm × 2mm DFN, over full operating temperature range | 3 | |
| Reference Voltage Line Regulation | 0.005 | %/V | 3 | ||||
| FB Pin Bias Current | 15 | 50 | nA | Note 5 | 3 | ||
| Switching Frequency | 0.9 | 1.1 | 1.3 | MHz | IDA < 500mA (LT3502), full temperature range | 3 | |
| Maximum Duty Cycle | 80 | 90 | % | 100mA Load (LT3502) | 3 | ||
| Switch VCESAT | 450 | mV | ISW = 500mA | 3 | |||
| Switch Current Limit | 0.75 | 0.9 | 1.1 | A | Note 3 | 3 | |
| Switch Active Current | 95 | 130 | µA | SW = 10V (Note 4) | 3 | ||
| Switch Active Current | 8 | 30 | µA | SW = 0V (Note 5) | 3 | ||
| BOOST Pin Current | 10 | 13 | mA | ISW = 500mA | 3 | ||
| Minimum BOOST Voltage Above Switch | 1.9 | 2.2 | V | ISW = 500mA | 3 | ||
| BOOST Schottky Forward Drop | 0.8 | 1 | V | IOUT = 100mA | 3 | ||
| DA Pin Current to Stop OSC | 500 | 650 | mA | 3 | |||
| SHDN Bias Current | 55 | 80 | µA | VSHDN = 5V | 3 | ||
| SHDN Bias Current | 1 | µA | VSHDN = 0V | 3 | |||
| SHDN Input Voltage High | 2 | V | 3 | ||||
| SHDN Input Voltage Low | 0.3 | V | 3 | ||||
| Input Voltage | VIN | 40 | V | 2 | |||
| BOOST Voltage | 50 | V | 2 | ||||
| BOOST Pin Above SW Pin | 7 | V | 2 | ||||
| FB Voltage | 6 | V | 2 | ||||
| SHDN Voltage | 40 | V | 2 | ||||
| BD Voltage | 7 | V | 2 | ||||
| Operating Junction Temperature Range | -40 | 125 | °C | LT3502I | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Thermal Resistance Junction to Ambient | θJA | 102 | °C/W | 8-lead 2mm × 2mm DFN | 2 |
CAD (KiCad official)
- Symbol:
LT3502IDC#TRMPBF - Footprint:
Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.45mm_EP0.64x1.37mm - 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files:
lt3502idc-trmpbf-etched.step/lt3502idc-trmpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3502idc-trmpbf.step/lt3502idc-trmpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (24 pp, sha256
ee1026fdeba3ecdd, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT3502IDC#TRMPBF
**Analog Devices** · DC-DC Converters · DFN-8-EP(2x2)
LT3502IDC#TRMPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Supplies current to the internal regulator and internal power switch, must be locally bypassed; input range 3V to 40V (absolute max 40V). |
| 2 | BD | power_in | Provides current to the internal boost Schottky diode; absolute maximum voltage 7V. |
| 3 | FB | input | Feedback pin regulated to 0.8V; connect the feedback resistor divider tap here, VOUT = 0.8(1 + R1/R2) with R2 of about 10k. |
| 4 | SHDN | input | Shutdown pin: tie to ground to shut down, tie to 2V or more for normal operation, tie to VIN if unused, also provides soft-start and frequency foldback, and must not exceed VIN. |
| 5 | GND | power_in | Ground pin. |
| 6 | DA | input | Connect the catch diode (D1) anode to this pin; used to provide frequency foldback in extreme situations. |
| 7 | BOOST | power_in | Provides a drive voltage higher than the input voltage to the internal NPN power switch; connect a boost capacitor from this pin to SW; absolute max 50V. |
| 8 | SW | output | Output of the internal power switch; connect to the inductor, catch diode and boost capacitor. |
| 9 | EP | power_in | Exposed pad (pin 9) is GND and must be soldered to the PCB. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-8-EP(2x2) |
| Category | Power Supply Chip |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Undervoltage Lockout | | 2.6 | 2.8 | 3 | V | | 3 |
| Quiescent Current at Shutdown | | | 0.5 | 2 | µA | VSHDN = 0V | 3 |
| Quiescent Current Not Switching | | | 1.5 | 2 | mA | | 3 |
| Feedback Voltage (2mm × 2mm DFN) | | 0.79 | 0.8 | 0.81 | V | 2mm × 2mm DFN, TA = 25°C | 3 |
| Feedback Voltage (2mm × 2mm DFN, full range) | | 0.785 | 0.8 | 0.813 | V | 2mm × 2mm DFN, over full operating temperature range | 3 |
| Reference Voltage Line Regulation | | | 0.005 | | %/V | | 3 |
| FB Pin Bias Current | | | 15 | 50 | nA | Note 5 | 3 |
| Switching Frequency | | 0.9 | 1.1 | 1.3 | MHz | IDA < 500mA (LT3502), full temperature range | 3 |
| Maximum Duty Cycle | | 80 | 90 | | % | 100mA Load (LT3502) | 3 |
| Switch VCESAT | | | 450 | | mV | ISW = 500mA | 3 |
| Switch Current Limit | | 0.75 | 0.9 | 1.1 | A | Note 3 | 3 |
| Switch Active Current | | | 95 | 130 | µA | SW = 10V (Note 4) | 3 |
| Switch Active Current | | | 8 | 30 | µA | SW = 0V (Note 5) | 3 |
| BOOST Pin Current | | | 10 | 13 | mA | ISW = 500mA | 3 |
| Minimum BOOST Voltage Above Switch | | | 1.9 | 2.2 | V | ISW = 500mA | 3 |
| BOOST Schottky Forward Drop | | | 0.8 | 1 | V | IOUT = 100mA | 3 |
| DA Pin Current to Stop OSC | | 500 | 650 | | mA | | 3 |
| SHDN Bias Current | | | 55 | 80 | µA | VSHDN = 5V | 3 |
| SHDN Bias Current | | | | 1 | µA | VSHDN = 0V | 3 |
| SHDN Input Voltage High | | 2 | | | V | | 3 |
| SHDN Input Voltage Low | | | | 0.3 | V | | 3 |
| Input Voltage | VIN | | | 40 | V | | 2 |
| BOOST Voltage | | | | 50 | V | | 2 |
| BOOST Pin Above SW Pin | | | | 7 | V | | 2 |
| FB Voltage | | | | 6 | V | | 2 |
| SHDN Voltage | | | | 40 | V | | 2 |
| BD Voltage | | | | 7 | V | | 2 |
| Operating Junction Temperature Range | | -40 | | 125 | °C | LT3502I | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| Thermal Resistance Junction to Ambient | θJA | | 102 | | °C/W | 8-lead 2mm × 2mm DFN | 2 |
## CAD (KiCad official)
- Symbol: `LT3502IDC#TRMPBF`
- Footprint: `Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.45mm_EP0.64x1.37mm`
- 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files: `lt3502idc-trmpbf-etched.step` / `lt3502idc-trmpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt3502idc-trmpbf.step` / `lt3502idc-trmpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/3502fd.pdf) (24 pp, sha256 `ee1026fdeba3ecdd`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt3502idc-trmpbf-datasheet.pdf)