main
Ray
Publish 0.1.0
78332eb
LT3437IDD#TRPBF
Analog Devices · DC-DC Converters · DFN-10-EP(3x3)
LT3437IDD#TRPBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | SW is the emitter of the on-chip power NPN switch, driven up to the input voltage during on-time, and needs an external Schottky catch diode to clamp negative excursions; SW operating rating is 60V. |
| 2 | VIN | power_in | VIN is the collector of the on-chip power switch and powers the internal control circuitry when BIAS is not present; operating maximum is 60V, with 80V allowed for 100ms transients at less than 15% duty cycle. |
| 3 | BOOST | power_in | BOOST supplies the drive voltage above VIN for the internal switch, with BOOST pin voltage above SW limited to 35V and operating voltage limited to 75V. |
| 4 | GND | power_in | GND is the reference for the regulated output and also the heat sink, and should be soldered together with the exposed pad to a copper ground plane. |
| 5 | CSS | passive | A capacitor from CSS to the regulated output sets the output voltage ramp rate at start-up, and the soft-start is defeated for FB above 0.9V (typical); CSS absolute maximum is 6V. |
| 6 | BIAS | input | BIAS connected to the regulated output reduces input current and improves efficiency, with a minimum output setting for this mode typically 2.7V; BIAS operating maximum is 60V. |
| 7 | VC | passive | VC is the error amplifier output and peak switch current comparator input used for compensation, sitting at about 0.45V at light load and 1.5V at maximum load, and driving it to ground disables switching. |
| 8 | FB | input | FB is the feedback input regulated to 1.25V through an external divider, and when it drops below 0.9V the switching frequency is reduced, SYNC is disabled and soft-start is enabled; FB absolute maximum is 6V. |
| 9 | SYNC | input | SYNC synchronizes the internal oscillator to an external logic signal of 25% to 75% duty cycle over a range up to 700kHz, and a level above 2V disables Burst Mode operation; SYNC absolute maximum is 6V. |
| 10 | SHDN | input | SHDN turns the regulator off and reduces input current to less than 1µA when below its 1.3V typical threshold, requiring above 1.3V to enable; SHDN operating maximum is 60V, with 80V allowed for 100ms transients at less than 15% duty cycle. |
| 11 | GND (EXPOSED PAD) | power_in | The exposed pad is ground and must be soldered to the PCB and to GND (pin 4) for low thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| SHDN Threshold | VSHDN | 1.15 | 1.3 | 1.45 | V | 2 | |
| SHDN Input Current | ISHDN | 5 | 30 | µA | SHDN = 12V | 2 | |
| Minimum Input Voltage | 2.5 | 3 | V | Note 3 | 2 | ||
| Supply Shutdown Current | IVINS | 0.1 | 2 | µA | SHDN = 0V, BOOST = 0V, FB/PGFB = 0V, BIAS = 0V | 2 | |
| Supply Sleep Current | 150 | 300 | µA | BIAS = 0V, FB = 1.35V | 2 | ||
| Supply Sleep Current | 45 | 75 | µA | FB = 1.35V | 2 | ||
| Supply Quiescent Current | IVIN | 1.35 | 2 | mA | BIAS = 0V, FB = 1.15V, VC = 0.8V, SYNC = 2V | 3 | |
| Supply Quiescent Current | IVIN | 0.475 | 1 | mA | BIAS = 5V, FB = 1.15V, VC = 0.8V, SYNC = 2V | 3 | |
| Minimum BIAS Voltage | 2.7 | 3.15 | V | Note 5 | 3 | ||
| BIAS Sleep Current | IBIASS | 110 | 180 | µA | Note 4 | 3 | |
| BIAS Quiescent Current | IBIAS | 0.75 | 1 | mA | SYNC = 2V | 3 | |
| Minimum Boost Voltage | 1.8 | 2.5 | V | ISW = 500mA, Note 6 | 3 | ||
| Input Boost Current | 11 | 16 | mA | ISW = 0.5A, Note 7 | 3 | ||
| Input Boost Current | 8 | 13 | mA | ISW = 0.25A, Note 7 | 3 | ||
| Reference Voltage | VREF | 1.225 | 1.25 | 1.275 | V | 3.3V < VVIN < 80V | 3 |
| FB Input Bias Current | IFB | 50 | 200 | nA | 3 | ||
| EA Source Current | 15 | 35 | 55 | µA | FB = 1.15V | 3 | |
| EA Sink Current | 15 | 30 | 55 | µA | FB = 1.35V | 3 | |
| VC High Clamp | 1.5 | 1.75 | 2.1 | V | 3 | ||
| IPK SW Current Limit | IPK | 500 | 650 | 900 | mA | 3 | |
| SW VCESAT Switch Saturation Voltage | VCESAT | 200 | 400 | mV | ISW = 250mA, Note 9 | 3 | |
| SW VCESAT Switch Saturation Voltage | VCESAT | 400 | 800 | mV | ISW = 500mA, Note 9 | 3 | |
| Switching Frequency | 165 | 200 | 240 | kHz | 3 | ||
| SYNC Frequency Range | 240 | 700 | kHz | 3 | |||
| Minimum SYNC Amplitude | 1.5 | 2 | V | 3 | |||
| CSS Current Threshold | ICSS | 4 | 10 | 16 | µA | FB = 0V, Note 10 | 3 |
| Maximum Duty Cycle | 95 | % | 3 | ||||
| EA Voltage Gain | 900 | V/V | Note 8 | 3 | |||
| EA Transconductance | gm | 650 | µMho | dI(VC) = ±10µA | 3 | ||
| VC to SW Transconductance | gm | 1 | A/V | 3 | |||
| VC Switching Threshold | 500 | mV | VSYNC = 2V | 3 | |||
| SYNC Input Impedance | 50 | kΩ | 3 | ||||
| VIN, SHDN, BIAS, SW Operating | 60 | V | Operating | 2 | |||
| VIN, SHDN 100ms Transient | 80 | V | 100ms transient, <15% duty cycle | 2 | |||
| BOOST Pin Above SW | 35 | V | 2 | ||||
| BOOST Pin Voltage Operating | 75 | V | Operating | 2 | |||
| BOOST Pin 100ms Transient | 85 | V | 100ms transient, <15% duty cycle | 2 | |||
| SYNC, CSS, FB | 6 | V | 2 | ||||
| Storage Temperature Range (DD Package) | Tstg | -65 | 125 | °C | DD package | 2 | |
| Operating Junction Temperature Range (LT3437IDD) | -40 | 125 | °C | Note 2 | 2 | ||
| Thermal Resistance Junction to Ambient | θJA | 45 | °C/W | 2 | |||
| Thermal Resistance Junction to Exposed Pad | θJC(PAD) | 10 | °C/W | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | resistance. Pin 4/Pin 8 and the exposed die pad, Pin 11/Pin 17, are connected by a continuous copper plate that runs | 20 |
CAD (KiCad official)
- Symbol:
LT3437IDD#TRPBF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lt3437idd-trpbf-etched.step/lt3437idd-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3437idd-trpbf.step/lt3437idd-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
e2cb79c469ba5793, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT3437IDD#TRPBF
**Analog Devices** · DC-DC Converters · DFN-10-EP(3x3)
LT3437IDD#TRPBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | SW is the emitter of the on-chip power NPN switch, driven up to the input voltage during on-time, and needs an external Schottky catch diode to clamp negative excursions; SW operating rating is 60V. |
| 2 | VIN | power_in | VIN is the collector of the on-chip power switch and powers the internal control circuitry when BIAS is not present; operating maximum is 60V, with 80V allowed for 100ms transients at less than 15% duty cycle. |
| 3 | BOOST | power_in | BOOST supplies the drive voltage above VIN for the internal switch, with BOOST pin voltage above SW limited to 35V and operating voltage limited to 75V. |
| 4 | GND | power_in | GND is the reference for the regulated output and also the heat sink, and should be soldered together with the exposed pad to a copper ground plane. |
| 5 | CSS | passive | A capacitor from CSS to the regulated output sets the output voltage ramp rate at start-up, and the soft-start is defeated for FB above 0.9V (typical); CSS absolute maximum is 6V. |
| 6 | BIAS | input | BIAS connected to the regulated output reduces input current and improves efficiency, with a minimum output setting for this mode typically 2.7V; BIAS operating maximum is 60V. |
| 7 | VC | passive | VC is the error amplifier output and peak switch current comparator input used for compensation, sitting at about 0.45V at light load and 1.5V at maximum load, and driving it to ground disables switching. |
| 8 | FB | input | FB is the feedback input regulated to 1.25V through an external divider, and when it drops below 0.9V the switching frequency is reduced, SYNC is disabled and soft-start is enabled; FB absolute maximum is 6V. |
| 9 | SYNC | input | SYNC synchronizes the internal oscillator to an external logic signal of 25% to 75% duty cycle over a range up to 700kHz, and a level above 2V disables Burst Mode operation; SYNC absolute maximum is 6V. |
| 10 | SHDN | input | SHDN turns the regulator off and reduces input current to less than 1µA when below its 1.3V typical threshold, requiring above 1.3V to enable; SHDN operating maximum is 60V, with 80V allowed for 100ms transients at less than 15% duty cycle. |
| 11 | GND (EXPOSED PAD) | power_in | The exposed pad is ground and must be soldered to the PCB and to GND (pin 4) for low thermal resistance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| SHDN Threshold | VSHDN | 1.15 | 1.3 | 1.45 | V | | 2 |
| SHDN Input Current | ISHDN | | 5 | 30 | µA | SHDN = 12V | 2 |
| Minimum Input Voltage | | | 2.5 | 3 | V | Note 3 | 2 |
| Supply Shutdown Current | IVINS | | 0.1 | 2 | µA | SHDN = 0V, BOOST = 0V, FB/PGFB = 0V, BIAS = 0V | 2 |
| Supply Sleep Current | | | 150 | 300 | µA | BIAS = 0V, FB = 1.35V | 2 |
| Supply Sleep Current | | | 45 | 75 | µA | FB = 1.35V | 2 |
| Supply Quiescent Current | IVIN | | 1.35 | 2 | mA | BIAS = 0V, FB = 1.15V, VC = 0.8V, SYNC = 2V | 3 |
| Supply Quiescent Current | IVIN | | 0.475 | 1 | mA | BIAS = 5V, FB = 1.15V, VC = 0.8V, SYNC = 2V | 3 |
| Minimum BIAS Voltage | | | 2.7 | 3.15 | V | Note 5 | 3 |
| BIAS Sleep Current | IBIASS | | 110 | 180 | µA | Note 4 | 3 |
| BIAS Quiescent Current | IBIAS | | 0.75 | 1 | mA | SYNC = 2V | 3 |
| Minimum Boost Voltage | | | 1.8 | 2.5 | V | ISW = 500mA, Note 6 | 3 |
| Input Boost Current | | | 11 | 16 | mA | ISW = 0.5A, Note 7 | 3 |
| Input Boost Current | | | 8 | 13 | mA | ISW = 0.25A, Note 7 | 3 |
| Reference Voltage | VREF | 1.225 | 1.25 | 1.275 | V | 3.3V < VVIN < 80V | 3 |
| FB Input Bias Current | IFB | | 50 | 200 | nA | | 3 |
| EA Source Current | | 15 | 35 | 55 | µA | FB = 1.15V | 3 |
| EA Sink Current | | 15 | 30 | 55 | µA | FB = 1.35V | 3 |
| VC High Clamp | | 1.5 | 1.75 | 2.1 | V | | 3 |
| IPK SW Current Limit | IPK | 500 | 650 | 900 | mA | | 3 |
| SW VCESAT Switch Saturation Voltage | VCESAT | | 200 | 400 | mV | ISW = 250mA, Note 9 | 3 |
| SW VCESAT Switch Saturation Voltage | VCESAT | | 400 | 800 | mV | ISW = 500mA, Note 9 | 3 |
| Switching Frequency | | 165 | 200 | 240 | kHz | | 3 |
| SYNC Frequency Range | | 240 | | 700 | kHz | | 3 |
| Minimum SYNC Amplitude | | | 1.5 | 2 | V | | 3 |
| CSS Current Threshold | ICSS | 4 | 10 | 16 | µA | FB = 0V, Note 10 | 3 |
| Maximum Duty Cycle | | | 95 | | % | | 3 |
| EA Voltage Gain | | | 900 | | V/V | Note 8 | 3 |
| EA Transconductance | gm | | 650 | | µMho | dI(VC) = ±10µA | 3 |
| VC to SW Transconductance | gm | | 1 | | A/V | | 3 |
| VC Switching Threshold | | | 500 | | mV | VSYNC = 2V | 3 |
| SYNC Input Impedance | | | 50 | | kΩ | | 3 |
| VIN, SHDN, BIAS, SW Operating | | | | 60 | V | Operating | 2 |
| VIN, SHDN 100ms Transient | | | | 80 | V | 100ms transient, <15% duty cycle | 2 |
| BOOST Pin Above SW | | | | 35 | V | | 2 |
| BOOST Pin Voltage Operating | | | | 75 | V | Operating | 2 |
| BOOST Pin 100ms Transient | | | | 85 | V | 100ms transient, <15% duty cycle | 2 |
| SYNC, CSS, FB | | | | 6 | V | | 2 |
| Storage Temperature Range (DD Package) | Tstg | -65 | | 125 | °C | DD package | 2 |
| Operating Junction Temperature Range (LT3437IDD) | | -40 | | 125 | °C | Note 2 | 2 |
| Thermal Resistance Junction to Ambient | θJA | | 45 | | °C/W | | 2 |
| Thermal Resistance Junction to Exposed Pad | θJC(PAD) | | 10 | | °C/W | | 2 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | resistance. Pin 4/Pin 8 and the exposed die pad, Pin 11/Pin 17, are connected by a continuous copper plate that runs | 20 |
## CAD (KiCad official)
- Symbol: `LT3437IDD#TRPBF`
- Footprint: `Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm`
- 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files: `lt3437idd-trpbf-etched.step` / `lt3437idd-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt3437idd-trpbf.step` / `lt3437idd-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/3437fc.pdf) (28 pp, sha256 `e2cb79c469ba5793`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt3437idd-trpbf-datasheet.pdf)