Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
LT3065EDD#PBF
Analog Devices · Linear Voltage Regulators (LDO) · DFN-10(3x3)
LT3065EDD#PBF from Analog Devices, in a DFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IN | power_in | Input supply pin for the 1.6V to 45V input range; withstands reverse voltage and needs a local 1µF to 10µF bypass capacitor if far from the main input filter. |
| 2 | IN | power_in | Second input supply pin, tied with pin 1, for the 1.6V to 45V input range with reverse-battery protection. |
| 3 | SHDN | input | Shutdown input that turns the output off when pulled low; connect to IN if unused, since the device does not function if SHDN is left unconnected. |
| 4 | PWRGD | output | Open-drain power-good output that pulls low when the output is below 90% of nominal, sinks 50µA, and needs an external pull-up resistor. |
| 5 | IMAX | passive | Precision current limit programming pin set by a resistor to GND, requires a 22nF decoupling capacitor to ground, and is tied to GND if unused. |
| 6 | REF/BYP | passive | Bypass/soft-start pin where a capacitor to GND (10nF gives 25µVRMS noise) lowers reference noise and sets soft-start time; leave floating if unused and do not drive it with active circuitry. |
| 7 | GND | power_in | Ground pin for the adjustable LT3065; connect the bottom of the external output-voltage resistor divider directly here and tie it to exposed pad pin 11. |
| 8 | ADJ | input | Error amplifier inverting input regulated to 600mV with typical 16nA bias current flowing out of the pin; connect the external resistor divider here to set output voltage from 0.6V to 40V. |
| 9 | OUT | power_out | Regulated output supplying the load, requiring a minimum 3.3µF ceramic output capacitor with ESR < 1Ω (4.7µF for outputs below 1.2V). |
| 10 | OUT | power_out | Second output pin, tied with pin 9, with the same minimum 3.3µF ceramic capacitor requirement and 0.6V to 40V permissible output range. |
| 11 | GND | power_in | Exposed pad is electrically GND and must be soldered to the PCB ground for proper electrical and thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-10(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| ADJ Pin Voltage (full temp) | VADJ | 588 | 600 | 612 | mV | 2.2V < VIN < 45V, 1mA < ILOAD < 500mA | 5 |
| ADJ Pin Voltage | VADJ | 594 | 600 | 606 | mV | VIN = 2.2V, ILOAD = 1mA | 5 |
| Minimum Input Voltage | VIN | 1.6 | 2.2 | V | ILOAD = 500mA | 5 | |
| Line Regulation | 0.1 | 3 | mV | ILOAD = 1mA, ΔVIN = 2.2V to 45V | 5 | ||
| Load Regulation | 0.1 | 4 | mV | ΔILOAD = 1mA to 500mA, VIN = 2.2V | 5 | ||
| Dropout Voltage | 110 | 210 | mV | ILOAD = 10mA | 5 | ||
| Dropout Voltage | 145 | 310 | mV | ILOAD = 50mA | 5 | ||
| Dropout Voltage | 175 | 330 | mV | ILOAD = 100mA | 5 | ||
| Dropout Voltage | 300 | 510 | mV | ILOAD = 500mA | 5 | ||
| GND Pin Current | 55 | 110 | µA | ILOAD = 0mA | 5 | ||
| GND Pin Current | 100 | 200 | µA | ILOAD = 1mA | 5 | ||
| GND Pin Current | 270 | 550 | µA | ILOAD = 10mA | 5 | ||
| GND Pin Current | 1.8 | 4.5 | mA | ILOAD = 100mA | 5 | ||
| GND Pin Current | 11 | 25 | mA | ILOAD = 500mA | 5 | ||
| Quiescent Current in Shutdown | 0.2 | 1 | µA | VIN = 45V, VSHDN = 0V | 5 | ||
| ADJ Pin Bias Current | 16 | 60 | nA | VIN = 2.2V | 5 | ||
| Shutdown Threshold On to Off | 0.9 | 1.1 | V | VOUT = On to Off | 5 | ||
| SHDN Pin Current | -1 | 1 | µA | VSHDN = 0V, VIN = 45V | 6 | ||
| SHDN Pin Current | 0.5 | 3 | µA | VSHDN = 45V, VIN = 45V | 6 | ||
| Ripple Rejection | 70 | 85 | dB | VIN, VOUT = 2V, VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 500mA | 6 | ||
| Input Reverse Leakage Current | 300 | µA | VIN = -45V, VOUT = 0 | 6 | |||
| Reverse Output Current | 0 | 10 | µA | VOUT = 1.2V, VIN = VSHDN = 0 | 6 | ||
| Internal Current Limit | 520 | mA | VIN = 2.2V, ∆VOUT = -5% | 6 | |||
| Internal Current Limit | 900 | mA | VIN = 2.2V, VOUT = 0, VIMAX = 0 | 6 | |||
| External Programmed Current Limit | 180 | 200 | 220 | mA | 5.6V < VIN < 10V, VOUT = 95% of VOUT (Nominal), RIMAX = 1.5k | 6 | |
| External Programmed Current Limit | 445 | 495 | 545 | mA | 5.6V < VIN < 7V, VOUT = 95% of VOUT (Nominal), RIMAX = 604Ω | 6 | |
| PWRGD Logic Low Voltage | 0.07 | 0.25 | V | Pull-Up Current = 50µA | 6 | ||
| PWRGD Leakage Current | 0.01 | 1 | µA | VPWRGD = 45V | 6 | ||
| PWRGD Trip Point | 86 | 90 | 94 | % | % of Nominal Output Voltage, Output Rising | 6 | |
| PWRGD Trip Point Hysteresis | 1.6 | % | % of Nominal Output Voltage | 6 | |||
| Output Voltage Noise | 90 | µVRMS | COUT = 10µF, ILOAD = 500mA, VOUT = 600mV, BW = 10Hz to 100kHz | 5 | |||
| Output Voltage Noise | 25 | µVRMS | COUT = 10µF, CBYP = 10nF, ILOAD = 500mA, VOUT = 600mV, BW = 10Hz to 100kHz | 5 | |||
| IN Pin Voltage | -50 | 50 | V | 2 | |||
| OUT Pin Voltage | -50 | 40 | V | 2 | |||
| Input-to-Output Differential Voltage | -40 | 50 | V | Note 2 | 2 | ||
| ADJ Pin Voltage | -50 | 50 | V | 2 | |||
| SHDN Pin Voltage | -50 | 50 | V | 2 | |||
| PWRGD Pin Voltage | -0.3 | 50 | V | 2 | |||
| IMAX Pin Voltage | -0.3 | 7 | V | 2 | |||
| REF/BYP Pin Voltage | 1 | V | 2 | ||||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | E-grade | 2 | |
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Maximum Junction Temperature | TJMAX | 150 | °C | DD package | 2 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 31 | °C/W | DD package | 2 | ||
| Thermal Resistance Junction-to-Case | θJC | 9 | °C/W | DD package | 2 |
CAD (KiCad official)
- Symbol:
LT3065EDD#PBF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10(3x3) (KiCad packages3D, STEP)
- 3D model files:
lt3065edd-pbf-etched.step/lt3065edd-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3065edd-pbf.step/lt3065edd-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
9bdafd2ba807157d, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).